MDD112C-N-030-N5M-130GB0伺服电机 PDF资料
1.产 品 资 料 介 绍：
MDD112C-N-030-N5M-130GB0 伺服电机简介
该型号属于 Bosch Rexroth / Indramat MDD 系列无刷交流伺服电机，特点是高动态响应、低转动惯量和高精度闭环控制，适用于 CNC 机床、自动化装配线、机器人关节以及高速精密运动平台。
结构与性能特点
稀土永磁同步电机设计
高效率、高转矩密度，保证运动响应速度与精度。低转动惯量（Low Inertia）
快速加减速能力强，适合短周期、高动态的工业运动。高分辨率反馈系统
“N5M” 表示配套数字编码器，可与 Indramat 驱动器实现闭环控制，确保位置、速度和扭矩的精确控制。坚固机械结构
高品质轴承与散热设计，适合长时间连续运行，抗工业环境干扰。标准法兰安装
方便与机械设备整合，接口标准化。
型号代码解析
MDD112C：机座号 112，C 级长度，适合高速、高动态性能应用
N-030：电气绕组代码，对应额定转速约 3000 rpm
N5M：数字式反馈编码器类型
130GB0：轴伸长度、安装法兰尺寸及机械接口配置
典型技术参数范围（基于 MDD112 系列）
具体数值可能随子型号略有差异，仅供参考：
额定扭矩：约 4–8 N·m
峰值扭矩：额定扭矩的 2–3 倍
额定转速：约 3000 rpm
最高转速：可达 4500–6000 rpm
绝缘等级：F 级
防护等级：IP54–IP65
冷却方式：自然散热 / 风冷
MDD112C-N-030-N5M-130GB0伺服电机 英文介绍
Introduction to MDD112C-N-030-N5M-130GB0 servo motor
This model belongs to the Bosch Rexroth/Indramat MDD series brushless AC servo motor, characterized by high dynamic response, low moment of inertia, and high-precision closed-loop control. It is suitable for CNC machine tools, automated assembly lines, robot joints, and high-speed precision motion platforms.
Structure and Performance Characteristics
Design of Rare Earth Permanent Magnet Synchronous Motor
High efficiency, high torque density, ensuring motion response speed and accuracy.
Low Inertia
Strong acceleration and deceleration ability, suitable for short cycle and high dynamic industrial movements.
High resolution feedback system
N5M "represents a matching digital encoder that can achieve closed-loop control with Indramat drivers, ensuring precise control of position, speed, and torque.
Durable mechanical structure
High quality bearings and heat dissipation design, suitable for long-term continuous operation, resistant to industrial environmental interference.
Standard flange installation
Facilitate integration with mechanical equipment and standardize interfaces.
Model code analysis
MDD112C: Machine base size 112, C-class length, suitable for high-speed and high dynamic performance applications
N-030: Electrical winding code, corresponding to a rated speed of approximately 3000 rpm
N5M: Digital Feedback Encoder Type
130GB0: Shaft extension length, installation flange size, and mechanical interface configuration
Typical technical parameter range (based on MDD112 series)
The specific values may vary slightly depending on the sub model, for reference only:
Rated torque: approximately 4-8 N · m
Peak torque: 2-3 times the rated torque
Rated speed: approximately 3000 rpm
Maximum speed: up to 4500-6000 rpm
Insulation level: F level
Protection level: IP54-IP5
Cooling method: natural heat dissipation/air cooling
MDD112C-N-030-N5M-130GB0伺服电机 产品展示
3.其他产品
3BHE017628R0002 PPD115A02 SG579989013 控制器模块
GE VMIVME-5565-010000 332-015565-010000 P反光内存模块
GE IS210MACCH1AKH控制器模块
4.其他英文产品
5SHY3545L0016 3BHB020720R0002 module
DS200DSPCH1ADA combustion engine card
IS215UCVEM01A IS215UCVEH2AF Gas turbine card
| IC3600LSRB1 | 531X184IPTAEG1 | IC3600EPSC1 |
| IC3600LSRA1 | 531X184IPTADG1 | IC3600EPSB1C |
| IC3600LSOC1B | 531X182IFGAJG1 | IC3600EPSB1B |
| IC3600LSOC1 | 531X182IFGAHG1 | IC3600EPSB1A |
| IC3600LSFD1B1B | 531X182IFGAEG1 | IC3600EPSB1 |
| IC3600LSFD1B | 531X1821FGAGG1 | IC3600EPSA1B1B |
| IC3600LSFD1 | 531X179PLMAKG1 | IC3600EPSA1B |
本篇文章出自瑞昌明盛自动化设备有限公司官网，转载请附上此链接:http://www.jiangxidcs
