SANYO DENKI PV1C015MXXXC00超级伺服放大器 PDF资料
1.产 品 资 料 介 绍：
一、产品概述
该型号属于 SANYO DENKI “PV Super”系列伺服放大器，适用于驱动高响应、高精度伺服电机，专为中等功率伺服系统设计。
二、典型技术规格（概略值）
额定输出功率：约 1.5 kW（驱动功率等级）
额定输出电流：约 9.4 A（在典型规格中）
供电电压：约 200 VAC 级别
冷却方式：空气冷却
通信接口：支持 DeviceNet 或 RS‑232 接口（视版本而定）
容量：适用于中功率伺服电机配合使用
重量：约 10 kg 级别
其他保护功能：过流、短路、过热保护等常见工业保护机制
三、产品特点
中等功率、高性能：1.5 kW 级别，适合中负载定位或驱动应用。
响应能力好：空气冷却、较快的电流转换能力，适合频繁启动／停止场景。
控制与接口灵活：支持多种通信协议，便于与现代自动化系统对接。
结构适工业环境：设计考虑散热、耐用、可靠性高。
维护方便：模块化、标准化设计，有利于系统维护或替换升级。
四、使用建议与选型注意事项
驱动器与伺服电机必须匹配功率、电压与额定电流，避免过载或性能不足。
确保供电电源干净、稳定，电压波动应在规格允许范围内。
安装位置应保证通风散热，避免热积累。
信号与编码器接线应采用屏蔽线，避免噪声影响反馈精度。
初次调试应从低速轻载状态开始，逐步调整增益、滤波、限幅等参数。
若系统产生再生能量或返馈电压，应考虑配套制动／再生模块。
SANYO DENKI PV1C015MXXXC00超级伺服放大器 英文介绍
1、 Product Overview
This model belongs to the SANYO DENKI "PV Super" series servo amplifier, suitable for driving high response, high-precision servo motors, designed specifically for medium power servo systems.
2、 Typical technical specifications (approximate values)
Rated output power: approximately 1.5 kW (driving power level)
Rated output current: approximately 9.4 A (in typical specifications)
Power supply voltage: approximately 200 VAC level
Cooling method: air cooling
Communication interface: Supports DeviceNet or RS-232 interface (depending on version)
Capacity: Suitable for use with medium power servo motors
Weight: Approximately 10 kg level
Other protection functions: common industrial protection mechanisms such as overcurrent, short circuit, overheating protection, etc
3、 Product Features
Medium power, high performance: 1.5 kW level, suitable for medium load positioning or drive applications.
Good responsiveness: air cooling, fast current conversion ability, suitable for frequent start/stop scenarios.
Flexible control and interface: Supports multiple communication protocols for easy integration with modern automation systems.
The structure is suitable for industrial environments: the design considers heat dissipation, durability, and high reliability.
Easy maintenance: Modular and standardized design, conducive to system maintenance or replacement upgrades.
4、 Usage suggestions and selection precautions
Drivers and servo motors must be matched with power, voltage, and rated current to avoid overload or insufficient performance.
Ensure that the power supply is clean and stable, and that voltage fluctuations are within the allowable range of specifications.
The installation location should ensure ventilation and heat dissipation to avoid heat accumulation.
Shielded wires should be used for signal and encoder wiring to avoid noise affecting feedback accuracy.
The initial debugging should start from a low-speed light load state, gradually adjusting parameters such as gain, filtering, and limiting.
If the system generates regenerative energy or feedback voltage, matching braking/regenerative modules should be considered.
SANYO DENKI PV1C015MXXXC00超级伺服放大器 产品展示
3.其他产品
ABB DSMB-01C 处理器
ABB AO2000 LS25 模拟输出模块
ABB UFC921A101 3BHE024855R0101控制主板模块
4.其他英文产品
ROLLS-ROYCE 5801-RRDIO15 WB I/O Alarm Module
NI CRI0-9073 Controller Module
A-B 1326AS-B440G-21 electric servo motor
| 4VM82-000-8 | 3090-SRK-2 | IC3600SVSA1 |
| 4VM81-220-5 | 3090-SPM2000 | IC3600SVFA1B |
| 4VM62-200-7 | HP56S261Z6 | IC3600SVFA1A |
| 4N63-100-2 | HG107A6 | IC3600SVFA1 |
| 4N63-100-1 | PXSWLPRCYL2062PRNO3WDCEURO | IC3600SVDE1 |
| 4N63-000-2 | HM606A6 | IC3600SVDD1C |
本篇文章出自瑞昌明盛自动化设备有限公司官网，转载请附上此链接:http://www.jiangxidcs
