SANYO DENKI 67ZA030A821S00伺服放大器 PDF资料
1.产 品 资 料 介 绍：
一、产品定位
型号带有 “67ZA030A” 标识，属于 SANYO DENKI BL Super / 放大器系列，是用于驱动交流伺服电机的功率放大器。
放大器用于将控制信号（脉冲、速度/位置指令）转换为电机所需的大功率电流与电压，以驱动伺服电机运行。
常见于中高功率的工业自动化系统，配合 SANYO DENKI 的 SANMOTION 伺服电机使用。
二、典型功能与特性
功率放大输出
能输出较大的电流和电压，从而驱动中至大型伺服电机，满足高扭矩负载需求。多种控制模式支持
可适应位置控制、速度控制、转矩控制等模式，以应对不同的应用需求。保护机制完善
包括过流、过压、欠压、短路、过热、反馈异常等多种保护功能，确保电机与系统安全。反馈兼容性
支持电机所需的反馈装置（如增量编码器、绝对编码器等），以实现精确的闭环控制。自动调谐 / 参数设定
放大器具备自动识别电机 / 负载特性、自动调整增益与滤波参数的能力，简化调试。散热与结构设计
采用良好散热结构（散热片 / 通风设计），保障大功率运行时温升受控。
三、使用注意点与校验建议
匹配性判断：必须确认该放大器的额定输出电流、电压与所驱动电机的额定参数匹配，避免过载或功率不足。
供电要求：除主电源外，该型号放大器可能需要额外的控制电源（逻辑电源）供给。
布线规范：电源线、编码器信号线必须采用屏蔽线、短线长度、避免干扰。
初次调试：建议低速空载运行检验信号及保护功能后，逐步加载、调参。
散热与环境：安装时确保有足够的通风／散热空间，避免高温、潮湿、灰尘聚集。
定期维护：定期检查风扇、散热片、连接端子与线路状况。
SANYO DENKI 67ZA030A821S00伺服放大器 英文介绍
1、 Product positioning
The model is labeled with "67ZA030A" and belongs to the SANYO DENKI BL Super/amplifier series. It is a power amplifier used to drive AC servo motors.
An amplifier is used to convert control signals (pulses, speed/position commands) into high-power current and voltage required by the motor to drive the servo motor to operate.
Commonly used in medium to high power industrial automation systems, in conjunction with SANYO DENKI's SANMOTION servo motors.
2、 Typical functions and features
Power amplification output
Capable of outputting large currents and voltages to drive medium to large servo motors, meeting high torque load requirements.
Multiple control modes supported
It can adapt to position control, speed control, torque control and other modes to meet different application requirements.
Improved protection mechanism
It includes multiple protection functions such as overcurrent, overvoltage, undervoltage, short circuit, overheating, and feedback abnormalities to ensure the safety of the motor and system.
Feedback compatibility
Support feedback devices required for motors (such as incremental encoders, absolute encoders, etc.) to achieve precise closed-loop control.
Automatic tuning/parameter setting
The amplifier has the ability to automatically identify motor/load characteristics, adjust gain and filtering parameters, and simplify debugging.
Heat dissipation and structural design
Adopting a good heat dissipation structure (heat sink/ventilation design) to ensure controlled temperature rise during high-power operation.
3、 Usage precautions and verification suggestions
Match judgment: It is necessary to confirm that the rated output current and voltage of the amplifier match the rated parameters of the driven motor to avoid overload or insufficient power.
Power supply requirements: In addition to the main power supply, this model of amplifier may require additional control power (logic power supply) supply.
Wiring specifications: Power lines and encoder signal lines must use shielded wires, short wire lengths, and avoid interference.
Initial debugging: It is recommended to test the signal and protection function during low-speed no-load operation, and then gradually load and adjust the parameters.
Heat dissipation and environment: Ensure sufficient ventilation/heat dissipation space during installation to avoid high temperatures, humidity, and dust accumulation.
Regular maintenance: Regularly check the condition of the fan, heat sink, connection terminals, and wiring.
SANYO DENKI 67ZA030A821S00伺服放大器 产品展示
3.其他产品
GE HWA143-TDM-PMC-V20 输入输出控制器模块
AB 1756-PA72 C直流电源模块
A-B 1756-OW16I/A 通道离散输出模块
4.其他英文产品
ABB G2000A5.7ST operation panel
HIMA H6200A Circuit Transmitter
Watlow Anafaze CLS208 208-1100110 Temperature Controller
| AMAT 0190-35217 | TP-2196-0 | PR6423/003-030+CON021 |
| AMAT 0100-90855 | TP-2204-2 | GPU/2/GS |
| AMAT 0100-09133 | TP-2242-1 | REF615 HBFFAEAGNBC6BNA |
| AMAT 0100-09034 | TP-2288-1 | SM811K01 3BSE018173R1 |
| AMAT 0100-18065 | TP-2326-1 | PM825 3BSE010796R1 |
| AMAT 0100-71175 | TP-5114-1 | 7625013-S |
本篇文章出自瑞昌明盛自动化设备有限公司官网，转载请附上此链接:http://www.jiangxidcs
