ABB 87TS01I-E GJR2368900R2340工控DCS系统
1.产 品 详 情 资 料：
R（un）和F（ault）LED均不亮。ABB 87TS01I-E GJR2368900R2340装置正在配置中。请留出时间以便最终确定。如果这种情况持续存在，并且CEX总线上没有其他单元LED亮起：•检查是否将包括ABB 87TS01I-E GJR2368900R2340在内的有效硬件配置下载到控制器。•检查PM8xx处理器单元内的CEX总线保险丝。•从PM8xx处理器单元启动复位信号（INIT）。•更换ABB 87TS01I-E GJR2368900R2340装置。•未下载任何应用程序。故障指示灯亮起ABB 87TS01I-E GJR2368900R2340装置正在重新启动过程中。请留出时间以便最终确定。如果情况依然存在，请更换单元。RxTx1/RxTx2（1）LED熄灭（1）由于信道CH2禁用，各以太网信道无接收或发送活动，LED将始终熄灭。RxTx1/RxTx2（1）LED闪烁各个以太网信道的接收或发送活动正常。由于ABB 87TS01I-E GJR2368900R2340不支持冗余，因此不使用DUAL LED。然而，在ABB 87TS01I-E GJR2368900R2340的单个配置中，PRIM LED亮起。ABB 87TS01I-E GJR2368900R2340支持热插拔。
Neither R(un) nor F(ault) LED's are ON The ABB 87TS01I-E GJR2368900R2340 unit is in the process of being configured. Allow time for this to finalize. If the condition persist, and no other unit LED on the CEX-Bus is ON: • Check that a valid HW configuration including the ABB 87TS01I-E GJR2368900R2340 is downloaded to the controller. • Check the CEX-Bus fuse inside the PM8xx processor unit. • Initiate a reset signal (INIT) from the PM8xx processor unit. • Replace the ABB 87TS01I-E GJR2368900R2340 unit. • None application is downloaded. F(ault) LED is ON The ABB 87TS01I-E GJR2368900R2340 unit is in the process of being restarted. Allow time for this to finalize. Replace unit if the condition persists. RxTx1/RxTx2(1) LED is OFF (1) LED will always be switched off due to disabling of channel CH2 No Receive or transmit activity for respective Ethernet channels. RxTx1/RxTx2(1) LED is flashing Receive or transmit activity for respective Ethernet channels is normal.Since ABB 87TS01I-E GJR2368900R2340 does not support redundancy, the DUAL LED is not used. However, the PRIM LED is ON in a single configuration of ABB 87TS01I-E GJR2368900R2340. ABB 87TS01I-E GJR2368900R2340 supports hot swap.
2.产 品 展 示
3.公 司 优 势 主 营 产 品
4.相 关 产 品 展 示
本篇文章出自瑞昌明盛自动化设备有限公司官网，转载请附上此链接:http://www.jiangxidcs.com
