BENTLY 3500/42M-01-00振动监测模块
1.产 品 介 绍
品牌：BENTLY
型号说明：BENTLY 3500/42M-01-00振动监测模块
优势：供应进口原装正品，专业停产配件。
公司主营特点：主营产品各种模块/卡件，控制器，触摸屏，伺服驱动器。
2.产 品 详 情 资 料：
BENTLY 3500/42M-01-00是一款机械震动测量模块，可以用于监测旋转机械设备（如发电机、压缩机、泵等）的机械振动和震动信号。以下是该产品的特点、使用方法和参数规格的简要介绍：
特点：
- 可以测量机械振动速度、加速度、位移和峰峰值等参数
- 具有高速数据采集和处理能力，能够实时监测设备的机械状态
- 支持多通道数据采集和传输
- 可以与BENTLY的其他监测设备（如3500/40M、3500/45等）组合使用，形成完整的机械监测系统
使用方法：
- 安装模块：将3500/42M-01-00模块插入到BENTLY 3500监测系统的插槽中，并连接到要监测的设备上。
- 配置参数：使用3500监测系统的配置软件，设置模块的采样率、滤波器、警报和故障阈值等参数。
- 监测设备状态：启动监测系统并开始采集数据，可以通过监测系统的显示屏或软件界面来查看设备的振动状态和警报信息。
参数规格：
- 通道数量：4个
- 采样率：1024 Hz
- 量程范围：振动速度（0-25mm/s）、振动加速度（0-30g）、振动位移（0-250μm）
- 滤波器类型：低通、高通、带通、带阻
- 阈值设置范围：警报阈值（0-20mm/s）、危险阈值（0-50mm/s）
- 输入阻抗：100MΩ
- 输出阻抗：100Ω
- 工作温度范围：-40°C到+70°C
需要注意的是，BENTLY 3500/42M-01-00模块是作为BENTLY 3500监测系统的一部分来使用的，所以在使用之前需要确保已经正确安装了整个监测系统并进行了相应的配置。
BENTLY 3500/42M-01-00 is a mechanical vibration measurement module that can be used to monitor the mechanical vibration and vibration signals of rotating mechanical equipment (such as generators, compressors, pumps, etc.). The following is a brief introduction of the product's features, use methods and parameter specifications:
characteristic:
It can measure mechanical vibration speed, acceleration, displacement, peak value and other parameters
With high-speed data acquisition and processing capability, it can monitor the mechanical status of equipment in real time
Support multi-channel data acquisition and transmission
It can be combined with other BENTLY monitoring equipment (such as 3500/40M, 3500/45, etc.) to form a complete mechanical monitoring system
usage method:
Install the module: Insert the 3500/42M-01-00 module into the slot of the BENTLY 3500 Monitoring System and connect it to the equipment to be monitored.
Configuration parameters: use the configuration software of the 3500 monitoring system to set the sampling rate, filter, alarm, fault threshold and other parameters of the module.
Monitoring equipment status: start the monitoring system and start collecting data. You can view the vibration status and alarm information of the equipment through the display screen or software interface of the monitoring system.
Parameter specification:
Number of channels: 4
Sample rate: 1024 Hz
Range: vibration speed (0-25mm/s), vibration acceleration (0-30g), vibration displacement (0-250 μ m）
Filter type: low-pass, high-pass, band-pass, band-stop
Threshold setting range: alarm threshold (0-20mm/s), hazard threshold (0-50mm/s)
Input impedance: 100M Ω
Output impedance: 100 Ω
Operating temperature range: - 40 ° C to+70 ° C
It should be noted that the BENTLY 3500/42M-01-00 module is used as a part of the BENTLY 3500 monitoring system, so it is necessary to ensure that the entire monitoring system has been correctly installed and configured before use
3.产 品 展 示
4.公 司 优 势 主 营 产 品
5.相 关 产 品 展 示
本篇文章出自瑞昌明盛自动化设备有限公司官网，转载请附上此链接:http://www.jiangxidcs.com
