REXROTH HDS04.2-W200N-HA36-01-FW电机驱动器
1.产 品 介 绍
品牌：REXROTH
型号说明：REXROTH HDS04.2-W200N-HA36-01-FW电机驱动器
优势：供应进口原装正品，专业停产配件。
公司主营特点：主营产品各种模块/卡件，控制器，触摸屏，伺服驱动器。
2.产 品 详 情 资 料：
REXROTH HDS04.2-W200N-HA36-01-FW如果用户设置损坏或不符合健全性检查，则可以使用此功能。有关Flash/PROM默认值，请参阅ENV命令（第5章）。位#2（GPI2）11-12保留供将来使用。位#3（GPI3）9-10设置为0（低）时，通知调试器它正在闪存中执行。当设置为1（高）时，如在没有VMEbus模型中设置的那样，通知调试器它正在PROM之外执行。Bit#4（GPI4）7-8对应用程序开放。Bit#5（GPI5）5-6对应用程序开放。Bit#6（GPI6）3-4对应用程序开放。Bit#7（GPI7）1-2对您的应用程序开放。请注意，当REXROTH HDS04.2-W200N-HA36-01-FW控制器冷复位时，162Bug将在Board Mode（板模式）下运行。使用环境（ENV）或菜单命令可以使162Bug在系统模式下运行。有关更多信息，请参阅第5章。2.通过在针脚1和针脚2之间安装/拆卸跳线来配置收割台J1。安装/拆除跳线可启用/禁用REXROTH HDS04.2-W200N-HA36-01-FW的系统控制器功能。在收割台J1的针脚1和针脚2之间安装/拆卸跳线可选择“自动”系统控制器功能。
This feature can be used in the event the user setup is corrupted or does not meet a sanity check. Refer to the ENV command (Chapter 5) for the Flash/PROM defaults. Bit #2 (GPI2) 11-12 Reserved for future use. Bit #3 (GPI3) 9-10 When set to 0 (low), informs the debugger that it is executing out of the Flash memory. When set to 1 (high), as set in no-VMEbus models, informs the debugger that it is executing out of the PROM. Bit #4 (GPI4) 7-8 Open to your application. Bit #5 (GPI5) 5-6 Open to your application. Bit #6 (GPI6) 3-4 Open to your application. Bit #7 (GPI7) 1-2 Open to your application.Note that when the REXROTH HDS04.2-W200N-HA36-01-FW controller comes up in a cold reset, 162Bug runs in Board Mode. Using the Environment (ENV) or MENU commands can make 162Bug run in System Mode. Refer to Chapter 5 for additional information. 2. Configure header J1 by installing/removing a jumper between pins 1 and 2. A jumper installed/removed enables/disables the system controller function of the REXROTH HDS04.2-W200N-HA36-01-FW. Installing/removing a jumper between pins 1 and 2 of header J1 selects the “automatic” system controller function.
3.产 品 展 示
4.公 司 优 势 主 营 产 品
5.相 关 产 品 展 示
本篇文章出自瑞昌明盛自动化设备有限公司官网，转载请附上此链接:http://www.jiangxidcs.com
