GE DS3820PIMB燃机系统板
例如，如果其中一个继电器被分配给报警功能，并且它也被分配给一个脉冲输出参数，则继电器将仅响应脉冲输出功能，是相欠电流水平d 100 A相欠电流延迟：10.0 s在0A时检测到欠电流：无相过电流继电器：断相过电流水平t 100 A相过电流延迟：10.0s相过电流激活：平均中性过电流继电器；断开中性过电流水平t100 A中性过电流延迟；10.0 s范围：0.5至600.0 s；步骤0.5 s范围：ALARM，AUX1，AUX2，AUX3，OFF[电流/电压]范围：NO，YES范围：0.5至600.0 s；步骤0.5 s范围：1至12000（步进1），或1至150%的CT（步进为1），由DETECT I/V ALARMS USE PERCENTAGE（使用百分比检测）值设置范围：AVERAGE（平均值），MAXIMUM CONTINUE ON NEXT PAGE（下一页最大值）范围：ALARM（报警），AUX1，AUX2，AUX3，OFF Range（关闭范围）：1至12000A（步进），或150%的CT insteps1，由DECT I/V ALARMS USE PERENTAGE（使用百分比）值设置，范围：0.5至600.0 s；步骤0.5 s范围：警报、AUX1、AUX2、AUX3、关闭消息消息消息范围：1到12000 A，步长为1，或1到100%CT，步长为为1，由DETECT I/V ALARMS USING PERCENTAGE（检测I/V警报使用百分比）值设置。
For example, if one of the relays is assigned to an alarm function and it is also assigned to one of the pulse output parameters, the relay will respond only to the pulse output function.nge: NO, YES PHASE UNDERCURRENT LEVEL d 100 A PHASE UNDERCURRENT DELAY: 10.0 s DETECT UNDERCURRENT WHEN 0A: NO PHASE OVERCURRENT RELAY: OFF PHASE OVERCURRENT LEVEL t 100 A PHASE OVERCURRENT DELAY: 10.0 s PHASE OVERCURRENT ACTIVATION: AVERAGE NEUTRAL OVERCURRENT RELAY: OFF NEUTRAL OVERCURRENT LEVEL t 100 A NEUTRAL OVERCURRENT DELAY: 10.0 s Range: 0.5 to 600.0 s; Step 0.5 s Range: ALARM, AUX1, AUX2, AUX3, OFF ] CURRENT/VOLTAGE ] Range: NO, YES Range: 0.5 to 600.0 s; Step 0.5 s Range: 1 to 12000 in steps of 1, or 1 to 150% of CT in steps of 1, set by the DETECT I/V ALARMS USING PERCENTAGE value Range: AVERAGE, MAXIMUM CONTINUED ON NEXT PAGE Range: ALARM, AUX1, AUX2, AUX3, OFF Range: 1 to 12000 A in steps of 1, or to 150% of CT instepsof1,set by the DETECT I/V ALARMS USING PERCENTAGE value Range: 0.5 to 600.0 s; Step 0.5 s Range: ALARM, AUX1, AUX2, AUX3, OFF MESSAGE MESSAGE MESSAGE Range: 1 to 12000 A in steps of 1, or 1 to 100% of CT in steps of 1, set by the DETECT I/V ALARMS USING PERCENTAGE value.
转载请附上此链接：http://www.jiangxidcs.com/
