HIEE200048R1工控备件机器人模块
安装-RX3i基于机架的以太网接口模块▪ 以太网端口连接器-嵌入式交换机-连接到10Base-T/100Base-TX/1000Base-T网络▪ Station Manager端口▪ 配置后验证以太网接口是否正确通电▪ 在网络PACSystems上ping TCP/IP以太网接口™ RX3i和RSTi EP TCP/IP以太网通信用户手册第3节GFK-2224Y 2019年8月安装和启动：以太网模块接口28 3.1以太网模块接口特性RX3i基于机架的以太网模块有两个版本。请注意下表中的差异：ETM001 Jx ETM001 Kxxx ETM001 Jx以太网模块提供：•一个以太网10Base-T/100Base TX接口•两个RJ-45以太网端口。这些端口中的一个或两个可以连接到其他以太网设备。每个端口自动检测所连接链路的数据速率（10 Mbps或100 Mbps）、双工（半双工或全双工）和布线布置（直通或交叉）。•一种嵌入式自动检测/自动切换以太网交换机，它提供了一种切换以太网数据和允许以太网电缆菊花链的方法，并提供了一个自动检测以太网电缆导线交叉的方法。ETM001 Kxxx以太网模块提供：•一个以太网10Base-T/1000BaseTX/1000Base-T接口•位于模块下侧的两个RJ45以太网端口。任何一个或两个端口都可以连接到其他以太网设备。每个端口自动检测所连接链路的数据速率（10 Mbps/100 Mbps/1000 Mbps）、双工（半双工或全双工）和布线布置（直通或交叉）。•一种嵌入式自动检测/自动切换以太网交换机，它提供了一种切换以太网数据和允许以太网电缆菊花链的方法，并提供了一个自动检测以太网电缆导线交叉的方法。图6:ETM001 Jx面板图7:ETM001 Kxxx面板PACSystems™ RX3i和RSTi EP TCP/IP以太网通信用户手册第3节GFK-2224Y 2019年8月安装和启动：以太网模块接口29 3.1.1前面板端口经修订的以太网模块ETM001 Kxxx已更新为RJ45端口。以太网端口支持IP上的Station Manager。前面板端口上的默认IP设置为10.10.0.100子网255.255.255.0，网关0.0.0.0。注意：前面板端口不支持仅限PACSAnalyzer Station Manager。3.1.2以太网端口连接ETM001或ETM001 Kxxx上的每个端口都独立运行，因此可以将以不同速度和/或双工模式运行的设备连接到端口。默认情况下，所有端口（甚至为空）都设置为“自动”，这将启用端口支持的最广泛选项的自动协商。可以在PME中的LAN1选项卡上手动配置端口连接速度，以实现较慢的速度（10/100 Mbps）。端口可以在全双工或半双工时自动协商至10/100/1000 Mbps。速度可通过硬件配置（ETM001 Kxxx）或AUP设置（ETM01）限制为10 Mbps或100 Mbps。1000 Mbps操作仅适用于ETM001 Kxxx上的自动协商。在ETM001 Kxxx上，半双工操作不会重新发送在硬件级别发生冲突的数据包。冲突报告为发送或接收错误，TCP重试或其他重试机制必须重新发送数据。嵌入式交换机存储数据包的内存有限。如果传入流量和传出流量之间存在速度差异，则由于资源限制，网络流量被丢弃的可能性会增加。例如，如果端口1具有建立的1000 Mbps链路，而端口2具有建立的100 Mbps链路，则必须缓冲从端口1传入和从端口2传出的流量，因为流量以比最大传入速率慢10倍的最大速率离开。随着网络负载的增加
Installation - RX3i Rack-Based Ethernet Interface Modules ▪ Ethernet Port Connectors - Embedded Switch - Connection to a 10Base-T/100Base-TX/1000Base-T Network ▪ Station Manager Port ▪ Verifying Proper Power-Up of the Ethernet interface After Configuration ▪ Pinging TCP/IP Ethernet interfaces on the Network PACSystems™ RX3i and RSTi-EP TCP/IP Ethernet Communications User Manual Section 3 GFK-2224Y August 2019 Installation and Start-up: Ethernet Module Interfaces 28 3.1 Ethernet Module Interface Characteristics There are two versions of the RX3i rack-based Ethernet module. Please note the differences in the table below: ETM001-Jx ETM001-Kxxx The ETM001-Jx Ethernet module provides: • An Ethernet 10Base-T/100Base-TX interface • Two RJ-45 Ethernet ports. Either or both of these ports can be attached to other Ethernet devices. Each port automatically sense the data rate (10 Mbps or 100 Mbps), duplex (half duplex or full duplex), and cabling arrangement (straight through or crossover) of the attached link. • An embedded autodetect/autoswitch Ethernet switch, which provides a means to switch Ethernet data and allow daisy chaining of Ethernet cabling, and provides a method to automatically detect Ethernet cable wire crossover. The ETM001-Kxxx Ethernet module provides: • An Ethernet 10Base-T/100BaseTX/1000Base-T interface • Two RJ45 Ethernet ports located on underside of module. Either or both ports can attach to other Ethernet devices. Each port automatically senses the data rate (10 Mbps/ 100 Mbps / 1000 Mbps), duplex (half duplex or full duplex), and cabling arrangement (straight through or crossover) of the attached link. • An embedded autodetect/autoswitch Ethernet switch, which provides a means to switch Ethernet data and allow daisy chaining of Ethernet cabling, and provides a method to automatically detect Ethernet cable wire crossover. Figure 6: ETM001-Jx Faceplate Figure 7: ETM001-Kxxx Faceplate PACSystems™ RX3i and RSTi-EP TCP/IP Ethernet Communications User Manual Section 3 GFK-2224Y August 2019 Installation and Start-up: Ethernet Module Interfaces 29 3.1.1 Front Panel Port The revised Ethernet module ETM001-Kxxx has been updated with an RJ45 port. The Ethernet port supports Station Manager over IP. The default IP settings on the front panel port are 10.10.0.100 subnet 255.255.255.0, gateway 0.0.0.0. Note: The Front panel port does not support PACSAnalyzer only Station Manager. 3.1.2 Ethernet Port Connections Each port on an ETM001 or ETM001-Kxxx operates independently, so devices that operate at different speeds and/or duplex modes may be attached to the ports. By default, all ports (even empty) are set for Automatic, which enables auto-negotiation for the widest range of options supported by the port. The port connection speed can be manually configured for slower speeds (10/100 Mbps) on the LAN1 tab in PME. The ports can auto-negotiate to 10/100/1000 Mbps at full or half duplex. The speed can be limited through Hardware Configuration (ETM001-Kxxx) or AUP settings (ETM001) to 10 Mbps or 100 Mbps. 1000 Mbps operation is only available with auto-negotiation on an ETM001-Kxxx. On the ETM001-Kxxx, half-duplex operation does not resend a packet that experiences a collision at the hardware level. A collision is reported as a send or receive error and TCP retries or other retry mechanisms must resend the data. Embedded switches have limited memory to store packets. If there is a speed difference between incoming traffic and outgoing traffic, there is an increased probability of network traffic being dropped due to resource limitations. For example, if Port 1 has an established 1000 Mbps link and Port 2 has an established 100 Mbps link, then traffic traveling in from Port 1 and out Port 2 must be buffered since traffic is leaving at a maximum rate 10 times slower than the maximum incoming rate. As the network loading increases, the likelihood
