HIEE300766R1工控模块机器人备件
–55dB最小隔离端口至背板和机架接地：250 Vac连续；1500 Vac持续1分钟，2550 Vdc持续1秒。有关产品标准和一般规范，请参阅附录A。为了满足EMC指令（CE标志）的发射和抗扰度要求，必须将屏蔽电缆与此模块一起使用。16.23.3 PRS015配置16.23.3.1模块参数参数默认描述信道值参考地址%AIxxxxx模块输入数据的起始地址。这默认为下一个可用的%AI块。通道值参考长度30（面向字的存储器）480（面向位的存储器）用于模块输入数据的字或位的数量。无论信道是否被使用，每个信道都被映射到2个字或32位。输入默认保持最后状态在模块故障或移除的情况下，此参数指定通道值参考的状态。强制关闭：将输入通道值设置为0并清除所有报警标志。保持最后状态：通道值保持其最后状态。诊断参考地址%Ixxxxx通道诊断状态数据的起始地址。这默认为下一个可用的%I块。诊断参考长度0信道诊断数据所需的位数或字数。默认值为0，这意味着禁用通道诊断映射。将其更改为非零值以启用通道诊断映射。0或30（面向字的存储器）0或480（面向位的存储器）命令输入数据参考地址%AIxxxxx模块命令输入数据的起始地址。这默认为下一个可用的%AI块。PACSystems*RX3i系统手册第16节GFK-2314T 2019年9月专用模块811参数默认描述命令输入数据参考长度6（面向字的存储器）96（面向位的存储器）模块命令输入数据所需的位数或字数。命令输出数据参考地址%AQxxxxx模块命令输出数据的起始地址。这默认为下一个可用的%AQ块。命令输出数据参考长度6（面向字的存储器）96（面向位的存储器）模块的命令输出数据所需的位或字的数量。模块状态参考地址%Ixxxxx模块状态数据的起始地址。这默认为选定内存区域中的下一个可用块。模块状态参考长度0模块状态数据所需的位数。默认值为0，这意味着模块状态数据的映射被禁用。将其更改为非零值以启用模块状态数据映射。2（面向字的存储器）32（面向位的存储器）I/O扫描集1在CPU扫描集选项卡中定义的要分配给此模块的扫描集。扫描集确定CPU轮询数据的频率。有效范围：1到32。16.23.3.2信道参数（信道1至15）参数默认描述信道启用禁用禁用、启用、模拟模式启用时，信道值将用相关LG1237的值更新。当选择模拟模式时，相关的LG1237将模拟指定的压力读数。模拟值10.0当通道启用设置为模拟模式时，以A/D单位报告的压力值。有效范围：-3.40282E+38至3.40282E+38。PACSystems*RX3i系统手册第16节GFK-2314T 2019年9月专用模块812参数默认描述信道值格式32位浮点只读：32位浮点高标度值（工程单位）1024.0用于缩放的上限值，以工程单位表示。有效范围：-3.40282E+38至3.40282E+38工程单位。注：如果高量程工程单位等于高量程A/D单位，而低量程工程单位则等于低量程A/D单位时，则禁用缩放。低比例值（工程单位）0.0用于缩放的以工程单位表示的较低值。有效范围：-3.40282E+38至3.40282E+38工程单位。低量程值（英制单位）参数不能等于高量程值（公制单位）参数。它可以更高
–55dB minimum Isolation Port to Backplane and to frame ground: 250 Vac continuous; 1500 Vac for 1 minute, 2550 Vdc for one second For product standards and general specifications, refer to Appendix A. To meet emission and immunity requirements for the EMC directive (CE mark), shielded cable must be used with this module. 16.23.3 PRS015 Configuration 16.23.3.1 Module Parameters Parameter Default Description Channel Value Reference Address %AIxxxxx Starting address for the input data of the module. This defaults to the next available %AI block. Channel Value Reference Length 30 (word oriented memory) 480 (bit oriented memory) The number of words or bits used for the input data of the module. Each channel is mapped to 2 words or 32 bits, whether the channel is used or not. Inputs Default Hold Last State In the event of module failure or removal, this parameter specifies the state of the Channel Value References. Force Off: Sets input channel values to 0 and clears all alarm flags. Hold Last State: Channel Values hold their last state. Diagnostic Reference Address %Ixxxxx Starting address for the channel diagnostics status data. This defaults to the next available %I block. Diagnostic Reference Length 0 The number of bits or words required for the Channel Diagnostics data. Default is 0, which means mapping of Channel Diagnostics is disabled. Change this to a non-zero value to enable Channel Diagnostics mapping. 0 or 30 (Word oriented memory) 0 or 480 (bit oriented memory) Command Input Data Reference Address %AIxxxxx Starting address for the command input data of the module. This defaults to the next available %AI block. PACSystems* RX3i System Manual Section 16 GFK-2314T Sept. 2019 Special Purpose Modules 811 Parameter Default Description Command Input Data Reference Length 6 (word oriented memory) 96 (bit oriented memory) The number of bits or words required for the command input data of the module. Command Output Data Reference Address %AQxxxxx Starting address for the command output data of the module. This defaults to the next available %AQ block. Command Output Data Reference Length 6 (word oriented memory) 96 (bit oriented memory) The number of bits or words required for the command output data of the module. Module Status Reference Address %Ixxxxx Starting address for the status data of the module. This defaults to the next available block in the selected memory area. Module Status Reference Length 0 The number of bits required for the Module Status data. Default is 0, which means mapping of Module Status data is disabled. Change this to a non-zero value to enable Module Status data mapping. 2 (word oriented memory) 32 (bit oriented memory) I/O Scan Set 1 The scan set, as defined in the CPU Scan Sets tab, to be assigned to this module. The scan set determines how often the CPU polls the data. Valid range: 1 through 32. 16.23.3.2 Channel Parameters (Channels 1 through 15) Parameter Default Description Channel Enable Disabled Disabled, Enabled, Simulation Mode When Enabled, the Channel Value will be updated with the value of the associated LG1237. When Simulation Mode is selected the associated LG1237 will simulate a specified pressure reading. Simulated Value 10.0 Pressure value to be reported, in A/D units when Channel Enable is set to Simulation Mode. Valid range: -3.40282E+38 through 3.40282E+38. PACSystems* RX3i System Manual Section 16 GFK-2314T Sept. 2019 Special Purpose Modules 812 Parameter Default Description Channel Value Format 32-bit Floatingpoint Read only: 32-bit floating-point High Scale Value (Eng Units) 1024.0 The upper value, in engineering units, used for scaling. Valid range: -3.40282E+38 through 3.40282E+38 engineering units. Note: Scaling is disabled if High Scale Eng. Units equals High Scale A/D Units and Low Scale Eng. Units equals Low Scale A/D Units. Low Scale Value (Eng Units) 0.0 The lower value, in engineering units, used for scaling. Valid range: -3.40282E+38 through 3.40282E+38 engineering units. The Low Scale Value (Eng Units) parameter cannot be equal to the High Scale Value (Eng Units) parameter. It can be higher
