HIEE300888R0001工控模块卡件
安装、操作或维护IC695PNS001时，人员必须确保通过使用接地ESD带或其他方式释放静电。如果IC695PNS001与以下背板版本一起使用，则此要求不适用：IC695CHS012-EA（或更高版本）IC695CHS016-EA（或者更高版本的）IC695CHS016EA-CA（或更低版本的）或IC695CHS007-BA（或更新版本的）IC 695SPC100A或更高的RX3i 10/100/1000Base-T铜质SFP PACSystems*RX3i系统手册第16节GFK-2314T 2019年9月专用模块786小型模块形状因子可插拔模块IC695SPF002A或更高版本RX3i 100Base FX（光纤2 km）SFP（多模光纤-MMF）IC695SPF550A或更低版本RX3i1000Base SX（光纤550 m）SFP（MMF）IC695SPF10A或更高型号RX3i 1000Base LX（光纤10 km）SFP（单模光纤-SMF）RX3i模块有关完整列表，请参阅PACSystems RX3i PROFINET扫描仪手册GFK2737。16.20.6兼容性：PNS101控制器CPU固件CPE400，CPL410，LAN2配置为嵌入式PROFINET控制器。CPU330固件版本9.55或更高CPU315/CPU320固件版本7.10或更高CPE302/CPE305/CPE310固件版本7.100或更高RXi控制器固件版本7.80或更新CRU320主固件版本8.00编程器软件Proficy Machine Edition版本9.50 SIM 8或更高版本RX3i PROFINET控制器IC695PNC001，固件版本1.20或更新（Simplex I/O）固件版本2.00或更高版本（冗余I/O）PACSystems*RX3i系统手册第16节GFK-2314T 2019年9月专用模块787 RX3i背板硬件扩展载体IC694CEE001连接到RX3i CEP001载体，并提供向远程节点添加一个额外RX3i IC694 I/O模块的能力。RX3i CEP001载体用作PROFINET IO设备。RX3i CEP001运营商的主要远程I/O功能包括：·扫描远程节点内的所有模块（输入和输出扫描）·在用户指定的生产周期将PROFINET网络上的数据发布到PROFINET IO控制器·在客户指定的生产期间从PROFINET网络中的PROFINET IO Controller接收数据·管理PROFINET通信和PROFINET IO控制器与远程节点内的模块之间的模块配置·在通信丢失时管理I/O状态·向PROFINET IOController发布故障信息（警报、诊断等）·为CEE001扩展载体供电I/O模块的插入和移除与RX3i通用背板相同。参考第2.6.4节。图408：IC695CEP001和IC694CEE001连接的PACSystems*RX3i系统手册第16节GFK-2314T 2019年9月专用模块789 RX3i CEP001载体提供两个RJ-45以太网插座。它支持10/100BASE-TX以太网标准接口。16.21.1功能·使用Proficy Machine Edition为所有受支持的RX3i I/O模块提供完整的编程和配置服务。请参阅“支持的I/O模块”一节。·支持菊花链/线、星形或环形（冗余介质）网络拓扑。·两个交换以太网端口：两个八芯RJ-45屏蔽双绞线10/100 Mbps铜接口。·使用WinLoader现场更新固件的USB端口。·支持使用PROFINET I/O的热备用CPU冗余：需要RX3i CEP001 2.01 GSDML 2.3版或更高版本。·支持使用PROFINET的HART®直通。注意：USB端口仅用于固件升级。
(or later) or IC695CHS007-AA (or later) When installing, operating, or maintaining the IC695PNS001, personnel must insure any electrostatic charge is discharged through the use of a grounded ESD strap or other means. This requirement does not apply if the IC695PNS001 is used with the following backplane revisions: IC695CHS012-EA (or later) IC695CHS016-EA (or later) IC695CHS012EA-CA (or later) IC695CHS016EA-CA (or later) or IC695CHS007-BA (or later) IC695SPC100A or later RX3i 10/100/1000Base-T copper SFP PACSystems* RX3i System Manual Section 16 GFK-2314T Sept. 2019 Special Purpose Modules 786 Small form-factor pluggable modules IC695SPF002A or later RX3i 100Base-FX (fiber 2 km) SFP (Multi-mode fiber - MMF) IC695SPF550A or later RX3i 1000Base-SX (fiber 550 m) SFP (MMF) IC695SPF010A or later RX3i 1000Base-LX (fiber 10 km) SFP (Single-mode fiber - SMF) RX3i modules For a complete list, refer to PACSystems RX3i PROFINET Scanner Manual, GFK2737. 16.20.6 Compatibility: PNS101 Controller CPU firmware CPE400, CPL410 with LAN2 configured as embedded PROFINET Controller. CPU330 firmware version 9.55 or later CPU315/CPU320 firmware version 7.10 or later CPE302/CPE305/CPE310 firmware version 7.10 or later RXi Controller firmware version 7.80 or later CRU320 Primary Firmware version 8.00 Programmer software Proficy Machine Edition version 9.50 SIM 8 or later RX3i PROFINET Controller IC695PNC001 with firmware version 1.20 or later (Simplex I/O) IC695PNC001 with firmware version 2.00 or later (Redundant I/O) PACSystems* RX3i System Manual Section 16 GFK-2314T Sept. 2019 Special Purpose Modules 787 RX3i backplane hardware Expansion Carrier IC694CEE001 attaches to the RX3i CEP001 Carrier and provides the ability to add one additional RX3i IC694 I/O module to the remote node. The RX3i CEP001 Carrier functions as a PROFINET IO-Device. The RX3i CEP001 Carrier’s main Remote I/O functions include: · Scanning all the modules within the remote node (input and output scan) · Publishing data on the PROFINET network to a PROFINET IO-Controller at a user-specified production period · Receiving data from a PROFINET IO-Controller on the PROFINET network at a customerspecified production period · Managing PROFINET communication and module configuration between a PROFINET IO-Controller and modules within the remote node · Managing the state of the I/O when communications is lost · Publishing fault information (alarms, diagnostics, and such) to the PROFINET IOController · Provides power to the CEE001 Expansion Carrier The insertion and removal of I/O modules is the same as in an RX3i Universal Backplane. Refer to Section 2.6.4. Figure 408: IC695CEP001 with IC694CEE001 Attached PACSystems* RX3i System Manual Section 16 GFK-2314T Sept. 2019 Special Purpose Modules 789 The RX3i CEP001 Carrier provides two RJ-45 Ethernet receptacles. It supports 10/100BASE-TX Ethernet standard interface. 16.21.1 Features · Full programming and configuration services for all supported RX3i I/O Modules using Proficy Machine Edition. Refer to the section, Supported I/O Modules. · Support daisy-chain/line, star, or ring (redundant media) network topologies. · Two switched Ethernet ports: two eight-conductor RJ-45 shielded-twisted pair 10/100 Mbps copper interfaces. · USB port for field updates of firmware using WinLoader. · Supports Hot-standby CPU Redundancy using PROFINET I/O: requires RX3i CEP001 2.01 GSDML version 2.3 or later. · Supports HART® Pass Through using PROFINET. Note: The USB port is for firmware upgrades only.
