HIEE300910R0001 UFC092BE01工控备件机器人模块
▪ LAN OK（局域网正常）指示灯指示接入以太网。当通过网络向以太网接口发送或从以太网接口接收数据时，LAN LED闪烁。当以太网接口未主动访问网络，但以太网物理接口可用且其中一个或两个以太网端口都可操作时，该开关保持打开。除非发生软件加载，否则为关闭。▪ 日志清空LED在正常操作期间亮起。如果已记录事件，则为Off（关闭）。▪ 两个以太网网络指示灯（LINK）指示网络链路状态。▪ 两个以太网网络速度LED（100 Mbps）指示网络数据速度（10（关闭）或100 Mb/sec（打开））。16.12.5.2以太网重启按钮该按钮用于手动重启以太网固件，无需重启整个系统。它是凹陷的，以防止意外操作。16.12.5.3连接器模块有两个10BaseT/100BaseTX以太网网络端口连接器。网络只有一个接口（只有一个以太网MAC地址和一个IP地址）。Station Manager（RS-232）串行端口通过前面板上的D连接器进行维修。图398：以太网功能ETM001 Jx PACSystems*RX3i系统手册第16节GFK-2314T 2019年9月专用模块755 16.12.6 ETM001 Kxxx接口控制和指示灯16.12.6.1 LED▪ OK LED指示模块是否能够执行正常操作。该LED在正常操作时亮起，在所有其他操作时闪烁。如果发生硬件或运行时故障，OK LED将闪烁两位数错误。▪ LAN OK（局域网正常）指示灯指示接入以太网。当通过网络向以太网接口发送或从以太网接口接收数据时，LAN OK LED闪烁。当以太网接口未主动访问网络，但以太网物理接口可用且其中一个或两个以太网端口都可操作时，它保持ON。除非发生软件加载，否则关闭。▪ 日志清空LED在正常操作期间亮起。如果记录了事件，则为OFF。▪ 以太网指示灯（LINK）指示网络链路状态。▪ 六个以太网网络速度LED（10/100/1000 Mbps）指示网络数据速度。16.12.6.2以太网重启按钮此按钮用于手动重启以太网固件，无需重启整个系统。它是凹陷的，以防止意外操作。16.12.6.3连接器模块有三个10BaseT/100BaseTX/1000BaseT以太网端口连接器。网络只有一个接口（只有一个以太网MAC地址和一个IP地址）。前面板有一个自动感应RJ-45连接器，它取代了早期设计的接口模块上的串行连接器。底部面板有两个自动感应RJ-45连接器，分别命名为Lan 1和Lan 2。图399：以太网功能ETM001 Kxxx PACSystems*RX3i系统手册第16节GFK-2314T 2019年9月专用模块756 16.13 RX3i DNP3输出模块：IC695EDS001 PACSystems*RX3i系统说明书第16节GFK-2314T2019年9月份专用模块757 PACSystems RX3i DNS3输出模块IC695EDSO01是一个以太网连接模块，可安装在RX3i背板和允许RX3i作为DNP3网络上的一个输出站，在那里它可以与多达八个DNP3主机交互。16.13.1模块功能：·两个带LED指示灯的自动感应RJ-45以太网端口o通过10BaseT或100BaseTX以太网连接o带自动协商、感应、速度和交叉检测的内部网络交换机o支持线性（菊花链）和星形网络配置o TCP/IP和LLA
▪ The LAN OK LED indicates access to the Ethernet network. The LAN LED blinks when data is being sent or received over the network directed to or from the Ethernet interface. It remains On when the Ethernet interface is not actively accessing the network but the Ethernet physical interface is available and one or both of the Ethernet ports is operational. It is Off otherwise unless software load is occurring. ▪ The Log Empty LED is On during normal operation. It is Off if an event has been logged. ▪ Two Ethernet network LEDs (LINK) indicate the network link status. ▪ Two Ethernet network speed LEDs (100 Mbps) indicate the network data speed (10 (off) or 100 Mb/sec (on)). 16.12.5.2 Ethernet Restart Pushbutton This pushbutton is used to manually restart the Ethernet firmware without power cycling the entire system. It is recessed to prevent accidental operation. 16.12.5.3 Connectors The module has two 10BaseT/100BaseTX Ethernet Network Port Connectors. There is only one interface to the network (only one Ethernet MAC address and only one IP address). The Station Manager (RS-232) Serial Port is serviced via the D-connector on the front panel. Figure 398: Ethernet Features ETM001-Jx PACSystems* RX3i System Manual Section 16 GFK-2314T Sept. 2019 Special Purpose Modules 755 16.12.6 ETM001-Kxxx Interface Controls and Indicators 16.12.6.1 LEDs ▪ The OK LED indicates whether the module is able to perform normal operation. This LED is ON for normal operation and flashing for all other operations. If a hardware or runtime failure occurs, the OK LED blinks a two-digit error. ▪ The LAN OK LED indicates access to the Ethernet network. The LAN OK LED blinks when data is being sent or received over the network directed to or from the Ethernet interface. It remains ON when the Ethernet interface is not actively accessing the network but the Ethernet physical interface is available and one or both of the Ethernet ports is operational. It is OFF otherwise unless software load is occurring. ▪ The LOG EMPTY LED is ON during normal operation. It is OFF if an event has been logged. ▪ The Ethernet network LED (LINK) indicate the network link status. ▪ Six Ethernet network speed LEDs (10/100/1000 Mbps) indicate the network data speed. 16.12.6.2 Ethernet Restart Pushbutton This pushbutton is used to manually restart the Ethernet firmware without power cycling the entire system. It is recessed to prevent accidental operation. 16.12.6.3 Connectors The module has three 10BaseT/100BaseTX/1000BaseT Ethernet Network Port Connectors. There is only one interface to the network (only one Ethernet MAC address and only one IP address). The front panel has an autosensing RJ-45 connector that has replaced the serial connector on the earlier design of the interface module. The bottom panel has two autosensing RJ-45 connectors designated as Lan 1 and Lan 2. Figure 399: Ethernet Features ETM001-Kxxx PACSystems* RX3i System Manual Section 16 GFK-2314T Sept. 2019 Special Purpose Modules 756 16.13 RX3i DNP3 Outstation Module: IC695EDS001 PACSystems* RX3i System Manual Section 16 GFK-2314T Sept. 2019 Special Purpose Modules 757 The PACSystems RX3i DNP3 Outstation Module IC695EDS001 is an Ethernet-connected module which fits in the RX3i backplane and permits the RX3i to behave as an Outstation on the DNP3 network, where it may interact with up to eight DNP3 masters. 16.13.1 Module features: · Two auto-sensing RJ-45 Ethernet ports with LED indicators o Connects via Ethernet at 10BaseT or 100BaseTX o Internal network switch with Auto-negotiate, Sense, Speed, and crossover detection o Supports Linear (daisy-chained) and Star network configurations o TCP/IP and LLA
