HIEE300910R1自动化模块备件
通信站管理器用户手册，GFK-2225 PACSystems*RX3i系统手册第16节GFK-2314T 2019年9月专用模块752▪ 16.12.1以太网接口规格：ETM001 Jx ETM001 Kxxx以太网处理器速度200 MHz连接器Station Manager（RS-232）端口：9针内螺纹D型连接器两个10BaseT/100BaseTX端口：两个8针内螺纹屏蔽RJ-45端口：三个自动感应RJ-45端口。LAN IEEE 802.2逻辑链路控制I类IEEE 802.3 CSMA/CD介质访问控制10/100 Mbps IEEE 802.2物理链路控制I级IEEE 802.3 CSMA/CD介质访问控制10/100/1000 Mbps IP地址数量一个一个以太网端口连接器两个，都是10BaseT/100BaseTX，带有自动感应RJ-45连接。三个，都是10BaseT/100BaseTX/1000BaseT，带有自动感应RJ-45连接。嵌入式以太网交换机是–允许以太网节点的菊花链。是–允许以太网节点的菊花链。串行端口Station Manager端口：RS232 DCE，1200-115200 bps。不适用。有关产品标准和一般规范，请参阅附录A 16.12.2以太网接口端口最新版本的以太网接口模块（-Kxxx）具有三个自动感应10BaseT/100BaseTX/1000BaseT RJ-45屏蔽双绞线以太网端口，用于连接到10BaseT、100BaseTX或1000BaseT IEEE 802.3网络。早期版本的以太网接口模块（-Jx）具有两个自动感应10BaseT/100BaseTX RJ-45屏蔽双绞线以太网端口，用于连接到10BaseT或100BaseTX IEEE 802.3网络。该端口自动检测速度（10Mbps或100Mbps）、双工模式（半双工或全双工）和连接到其上的电缆（直通或交叉），无需干预。网络只有一个接口（只有一个以太网MAC地址和一个IP地址）。PACSystems*RX3i系统手册第16节GFK-2314T 2019年9月专用模块753 16.12.3 Station Manager 92以太网接口模块的内置Station Manager功能通过Station Manager端口或以太网电缆提供对以太网接口的在线监控访问。Station Manager服务包括：▪ 用于询问和控制电台的一组交互式命令。▪ 无限制访问以观察内部统计信息、异常日志和配置参数。▪ 更改工作站参数或操作的命令的密码安全。有关Station Manager的完整信息，请参阅PACSystems TCP/IP以太网通信Station Manager用户手册GFK-2225。16.12.4以太网全局数据（EGD）每个PACSystems CPU支持多达255个同时进行的以太网全局数据交换。EGD交换机使用编程器进行配置，并存储在PLC中。可以配置生产和消费交换。PACSystems以太网接口支持EGD交换机的选择性消费和EGD交换机生产以及本地子网广播IP地址的消费。以太网接口可以配置为使用SNTP来同步生成的EGD交换的时间戳。以太网接口模块实现1类和2类设备的功能。COMMREQ驱动的EGD命令可在应用程序中用于读取数据并将数据写入CPU或其他EGD Class 2设备。92此功能仅适用于ETM001 Jx。ETM001 Kxxx上的Station Manager串行端口已被模块正面的自动感应RJ45端口取代。PACSystems*RX3i系统手册第16节GFK-2314T 2019年9月专用模块754 16.12.5 ETM001 Jx接口控制和指示灯16.12.5.1 LED▪ 以太网OK LED指示模块是否能够执行正常操作。该LED在正常操作时亮起，在所有其他操作时闪烁。如果发生硬件或运行时故障，EOK LED闪烁两位数错误。
Communications Station Manager User Manual, GFK-2225 PACSystems* RX3i System Manual Section 16 GFK-2314T Sept. 2019 Special Purpose Modules 752 ▪ 16.12.1 Ethernet Interface Specifications: ETM001-Jx ETM001-Kxxx Ethernet processor speed 200 MHz Connectors Station Manager (RS-232) Port: 9-pin female D-connector Two 10BaseT / 100BaseTX Ports: Two 8-pin female shielded RJ-45 Ports: Three autosensing RJ-45 ports. LAN IEEE 802.2 Logical Link Control Class I IEEE 802.3 CSMA/CD Medium Access Control 10/100 Mbps IEEE 802.2 Logical Link Control Class I IEEE 802.3 CSMA/CD Medium Access Control 10/100/1000 Mbps Number of IP addresses One One Number of Ethernet Port Connectors Two, both are 10BaseT / 100BaseTX with auto-sensing RJ-45 connection. Three, all are 10BaseT/100BaseTX/1000BaseT with auto-sensing RJ-45 connection. Embedded Ethernet Switch Yes – Allows daisy chaining of Ethernet nodes. Yes – Allows daisy chaining of Ethernet nodes. Serial Port Station Manager Port: RS232 DCE, 1200 - 115200 bps. Not Applicable. For product standards and general specifications, refer to Appendix A. 16.12.2 Ethernet Interface Ports The latest version of the Ethernet Interface Module (-Kxxx) has three auto-sensing 10BaseT/100BaseTX/1000BaseT RJ-45 shielded twisted pair Ethernet ports for connection to a 10BaseT, 100BaseTX, or 1000BaseT IEEE 802.3 network. The early version of the Ethernet Interface Module (-Jx) has two auto-sensing 10BaseT/100Base TX RJ-45 shielded twisted pair Ethernet ports for connection to either a 10BaseT or 100BaseTX IEEE 802.3 network. The port automatically senses the speed (10Mbps or 100Mbps), duplex mode (half duplex or full duplex) and cable (straight-through or crossover) attached to it with no intervention required. There is only one interface to the network (only one Ethernet MAC address and only one IP address). PACSystems* RX3i System Manual Section 16 GFK-2314T Sept. 2019 Special Purpose Modules 753 16.12.3 Station Manager92 The built-in Station Manager function of the Ethernet Interface Module provides on-line supervisory access to the Ethernet Interface, through the Station Manager port or over the Ethernet cable. Station Manager services include: ▪ An interactive set of commands for interrogating and controlling the station. ▪ Unrestricted access to observe internal statistics, an exception log, and configuration parameters. ▪ Password security for commands that change station parameters or operation. Refer to the PACSystems TCP/IP Ethernet Communications Station Manager User Manual, GFK-2225, for complete information on the Station Manager. 16.12.4 Ethernet Global Data (EGD) Each PACSystems CPU supports up to 255 simultaneous Ethernet Global Data (EGD) exchanges. EGD exchanges are configured using the programmer and stored into the PLC. Both Produced and Consumed exchanges can be configured. PACSystems Ethernet Interfaces support both selective consumption of EGD exchanges and EGD exchange production and consumption to the broadcast IP address of the local subnet. The Ethernet Interface can be configured to use SNTP to synchronize the timestamps of produced EGD exchanges. The Ethernet Interface Module implements the capabilities of a Class 1 and Class 2 device. COMMREQ-driven EGD Commands can be used in the application program to read and write data into the CPU or other EGD Class 2 devices. 92 This feature only applies to ETM001-Jx. The Station Manager serial port has been replaced on the ETM001-Kxxx by an autosensing RJ45 port on the face of the module. PACSystems* RX3i System Manual Section 16 GFK-2314T Sept. 2019 Special Purpose Modules 754 16.12.5 ETM001-Jx Interface Controls and Indicators 16.12.5.1 LEDs ▪ The Ethernet OK LED indicates whether the module is able to perform normal operation. This LED is On for normal operation and flashing for all other operations. If a hardware or runtime failure occurs, the EOK LED blinks a two-digit error.
