HIEE300936R0101 UFC718AE01工控模块系统备件
适用于电子线路轴应用的传动装置。§完整自动化控制解决方案的单一软件开发环境简化了编程。§分布式架构可提高机器灵活性–使用抗噪声光纤电缆在轴之间的距离可达100米§可选光纤接线板允许分布式以运动为中心的I/O，以降低布线复杂性和成本。§每个轴有两个高速位置捕捉输入，用于登记和顺序控制。该模块与除CRU320之外的所有机架式RX3i CPU兼容。它可以安装在任何可用的RX3i I/O插槽中。模块支持插入和取出通电的RX3i通用背板。参见第2.6.4.1节热插拔。图392:IC695PMM335 PACSystems*RX3i系统手册第16节GFK-2314T 2019年9月专用模块745 16.10.3光纤I/O接线板DIN导轨式FTB IC695FTB001允许用户通过距离PMM335 100米的全双工光纤链路将5伏、24伏和模拟I/O连接到运动特定设备，如限位开关和编码器。FTB I/O可配置为超行程开关、主开关、正交编码器和高速触摸探头位置捕捉输入、数字凸轮开关输出或通用I/O。FTB的模拟输出可以用作通用模拟输出，或配置用于闭合位置环路。当数据在PMM和FTB之间发送时，强大的串行协议对数据进行编码和解码。如果发生系统故障，例如失去与PMM的通信，FTB将其I/O设置为用户配置状态。16.10.4功能§光纤连接允许选择1m至100m的电缆长度§光纤连接提供主机架和FTB之间的光学隔离。§所有24V输出的电流能力为0.5A。§5V差分输入（正交编码器线路）上的编码器丢失和断线故障检测。§通过指示I/O点状态的单个LED提供视觉诊断。§DIN导轨安装允许方便地定位I/O。PACSystems*RX3i系统手册第16节GFK-2314T 2019年9月专用模块746§光纤接口降低了远程I/O布线成本并提高了抗噪声能力。§可拆卸RX3i接线盒头提供了易用性§外部正交编码器16.11 IEC 61850以太网通信模块：IC695ECM850的5Vdc电源PACSystems RX3i IEC 61850 Ethernet通信模块IC695ECM85（ECM850）将RX3i控制器连接到IEC 61850网络，使得控制器能够充当IEC 61850客户端并使用IEC 61850协议与网络上的智能电子设备（IED、IEC 61850服务器）通信。（IEC 61850是变电站设计的标准IEC 61850客户端功能o与IED的多个连接o读取和写入数据值o控制模型–所有模型o异常报告–报告缓冲和未缓冲o浏览数据模型–逻辑设备、节点、数据对象和属性o自我描述–通过IEC 61850网络从IED读取数据模型§完整IEC 61850客户端的编程和配置服务，包括读取设备变电站配置语言（SCL）文件以及使用Machine Edition编程和配置应用程序直接从IED在线读取配置数据。PACSystems*RX3i系统手册第16节GFK-2314T 2019年9月专用模块747§支持热备用冗余系统中的操作。
gearing features for electronic line shaft applications. § Single software development environment for complete automation control solution simplifies programming. § Distributed architecture for greater machine flexibility – up to 100 meters between axes using noise immune fiber cables § Optional Fiber Terminal Block allows distributed motion-centric I/O to reduce wiring complexity and cost. § Two high-speed position capture inputs per axis for registration and sequence control. This module is compatible with all rack-mounted RX3i CPUs except CRU320. It can be installed in any available RX3i I/O slot. Module supports insertion into and removal from an RX3i Universal Backplane which is under power. Refer to Hot Insertion and Removal, Section 2.6.4.1. Figure 392: IC695PMM335 PACSystems* RX3i System Manual Section 16 GFK-2314T Sept. 2019 Special Purpose Modules 745 16.10.3 Fiber I/O Terminal Block The DIN-rail mounted FTB, IC695FTB001, allows the user to connect 5-volt, 24-volt, and analog I/O to motion specific devices, such as limit switches and encoders, over a full-duplex fiber optic link up to 100m from the PMM335. FTB I/O can be configured as over-travel switch, home switch, quadrature encoder and highspeed touch probe position capture inputs, digital cam switch outputs or general purpose I/O. The FTB’s analog outputs can be used as general-purpose analog outputs, or configured for closed position loop A robust serial protocol encodes and decodes the data as it sent between the PMM and the FTB. In the event of a system malfunction, such as loss of communication with the PMM, the FTB sets its I/O to the user-configured state. 16.10.4 Features § Fiber optic connection allows choice of cable lengths from 1m to 100m § Fiber optic connection provides optical isolation between the main rack and the FTB. § Current capability to 0.5A on all 24V outputs. § Loss of encoder and open wire fault detection on 5V differential inputs (quadrature encoder lines). § Visual diagnostics provided via individual LEDs that indicate I/O point state. § DIN-rail mounting allows convenient location of I/O. PACSystems* RX3i System Manual Section 16 GFK-2314T Sept. 2019 Special Purpose Modules 746 § Fiber optic interface reduces remote I/O wiring cost and improves noise immunity. § Removable RX3i terminal block headers provide ease of use § A 5Vdc power source for external quadrature encoders 16.11 IEC 61850 Ethernet Communication Module: IC695ECM850 The PACSystems RX3i IEC 61850 Ethernet Communication Module, IC695ECM850 (ECM850), connects an RX3i controller to an IEC 61850 network, enabling the controller to act as an IEC 61850 Client and communicate with Intelligent Electronic Devices (IEDs, IEC 61850 servers) on the network using the IEC 61850 protocol. (IEC 61850 is a standard for the design of electrical substation IEC 61850 client features o Multiple connections to IEDs o Read and write of data values o Control model – all models o Report by exception – reporting buffered and un-buffered o Browse data model – logical devices, nodes, data objects & attributes o Self-description – reads data model from IED over IEC 61850 network § Full programming and configuration services for the IEC 61850 Client, including reading of device Substation Configuration Language (SCL) files and reading configuration data online directly from IEDs using the Machine Edition programming and configuration application. PACSystems* RX3i System Manual Section 16 GFK-2314T Sept. 2019 Special Purpose Modules 747 § Supports operation in hot standby redundant systems.
