IS200BPIAG1A通用电气卡件
IC697CBL811电缆，RCM通信（10英尺）I/O扩展电缆成熟IC697CBL926电缆，RCM通信（25英尺）I/O扩展电缆材料806766A5.CDR SR469在服务中已停止R1跳闸设定点访问启动R2辅助计算机RS232运行R3辅助R4警报R5阻止启动R6服务消息热RTD负载损失469电机管理继电器®程序端口设定点7 8 9 4 5 6 12 3。0帮助信息值实际退出输入重置下一次重置可能的计算机RS485辅助RS485锁定SR469状态电机状态输出继电器过载传感器不平衡传感器接地传感器R E G I S T E R E D 469电机管理继电器®说明书469固件版本：30E281.000 469PC软件版本：2.8x手册P/N：1601-0057-D9（GEK-106289A）版权所有©2001 GE Power管理GE Power Management 215 Anderson Avenue，Markham，Ontario Canada L6E 1B3电话：（905）294-6222传真：（905）294-8512互联网：http://www.GEindustrial.com/pm根据ISO9001注册体系制造。g GE电力管理警告这些说明不旨在涵盖设备的所有细节或变化，也不提供与安装、操作或维护相关的所有可能的应急情况。如果需要进一步的信息，或者出现了买方无法充分解决的特殊问题，则应将此事提交给通用电气公司。在要求的范围内，本文所述产品符合适用的ANSI、IEEE和NEMA标准；但由于地方法规和条例差异很大，因此没有提供此类保证。GE Power Management 469电机管理继电器i目录1。简介1.1概述1.1.1管理继电器是一种基于微处理器的继电器，用于保护和管理中、大马力电机和驱动设备。469配备了六个输出继电器，用于跳闸、报警和启动块。电机保护、故障诊断、功率计量和RTU功能集成在一个经济型抽出式组件中。下面的单线图说明了使用ANSI（美国国家标准协会）设备编号的469功能。图1–1：单线图典型应用包括：•泵•风扇•压缩机•磨机•碎纸机•挤出机•除泥机•精炼机•起重机•输送机•冷却机•破碎机•鼓风机1-2 469电机管理继电器GE Power Management 1.1概述1简介1此处详细介绍了一些保护亮点；完整列表如下所示。四个可分配的数字输入可配置用于许多不同的功能，包括转速表或通用跳闸和具有可编程名称的报警。热模型包括不平衡偏置、RTD反馈和指数冷却。除了15条标准过载曲线外，还有一条自定义曲线特性和一条专门为高惯性负载启动而设计的曲线，当加速时间超过安全失速时间时。为双速电机提供第二过载曲线。可使用
IC697CBL811 Cable, RCM Communications (10 feet) I/O Expansion Cable Mature IC697CBL826 Cable, RCM Communications (25 feet) I/O Expansion Cable Mature806766A5.CDR SR469 IN SERVICE STOPPED R1 TRIP SETPOINT ACCESS STARTING R2 AUXILIARY COMPUTER RS232 RUNNING R3 AUXILIARY R4 ALARM R5 BLOCK START R6 SERVICE MESSAGE HOT RTD LOSS OF LOAD 469 Motor Management Relay® PROGRAM PORT SETPOINT 7 8 9 4 5 6 12 3 . 0 HELP MESSAGE VALUE ACTUAL ESCAPE ENTER RESET NEXT RESET POSSIBLE COMPUTER RS485 AUXILIARY RS485 LOCKOUT SR469 STATUS MOTOR STATUS OUTPUT RELAYS OVERLOAD PICKUP UNBALANCE PICKUP GROUND PICKUP R E G I S T E R E D 469 MOTOR MANAGEMENT RELAY® Instruction Manual 469 Firmware Revision: 30E281.000 469PC Software Revision: 2.8x Manual P/N: 1601-0057-D9 (GEK-106289A) Copyright © 2001 GE Power Management GE Power Management 215 Anderson Avenue, Markham, Ontario Canada L6E 1B3 Tel: (905) 294-6222 Fax: (905) 294-8512 Internet: http://www.GEindustrial.com/pm Manufactured under an ISO9001 Registered system. g GE Power Management WARNING These instructions do not purport to cover all details or variations in equipment nor provide for every possible contingency to be met in connection with installation, operation, or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s purpose, the matter should be referred to the General Electric Company. To the extent required the products described herein meet applicable ANSI, IEEE, and NEMA standards; but no such assurance is given with respect to local codes and ordinances because they vary greatly. GE Power Management 469 Motor Management Relay i TABLE OF CONTENTS 1. INTRODUCTION 1.1 OVERVIEW 1.1.1 Management Relay is a microprocessor based relay designed for the protection and management of medium and large horsepower motors and driven equipment. The 469 is equipped with six output relays for trips, alarms, and start blocks. Motor protection, fault diagnostics, power metering, and RTU functions are integrated into one economical drawout package. The single-line diagram below illustrates the 469 functionality using ANSI (American National Standards Institute) device numbers. Figure 1–1: SINGLE LINE DIAGRAM Typical applications include: • Pumps • Fans • Compressors • Mills • Shredders • Extruders • Debarkers • Refiners • Cranes • Conveyors • Chillers • Crushers • Blowers 1-2 469 Motor Management Relay GE Power Management 1.1 OVERVIEW 1 INTRODUCTION 1 Some of the protection highlights are detailed here; a complete list is shown below. Four assignable digital inputs may be configured for a number of different features including tachometer or generic trip and alarm with a programmable name. The thermal model incorporates unbalance biasing, RTD feedback, and exponential cooling. In addition to the 15 standard overload curves, there is a custom curve feature and a curve specifically designed for the starting of high inertia loads, when the acceleration time exceeds the safe stall time. A second overload curve is provided for two-speed motors. Ground faults or earth leakage as low as 0.25 A may be detected using the
