IS200BPPH2B工控备件机器人模块
•欠压自动重启(可选)•转子断条检测系统(可选)?VT保险丝故障输入和输出电流和电压输入469有两组三相CT输入,一组用于相电流,另一组用于差动保护。订购继电器时,必须指定相电流输入(1A和5A)的额定值,而差分输入的额定值可现场编程,支持1A和5A二次电流。还有2个单相接地CT输入:具有可设置次级额定值的标准输入;以及用于高电阻接地系统的高灵敏度接地电流检测输入。三相VT输入支持三角形和Y形配置,并为所有基于电压、频率和功率的保护元件和计量提供电压信号。数字输入469有5个预定义的输入:•启动器状态•紧急重启•远程重置•设定点访问•测试开关469还有四个可分配的数字输入,可配置为以下功能:•远程跳闸和报警•速度开关跳闸和转速计•振动开关跳闸和报警、压力开关跳闸和警报•甩负荷跳闸•通用数字计数器•外部示波器触发和外部继电器故障模拟启动•具有可编程功能和输出模拟输入的通用开关输出使用469中可用的四个可配置模拟输入来测量从标准传感器馈送至继电器的电机操作相关量。每个输入可单独设置为测量4-20 mA、0-20 mA或0-1 mA传感器信号。469还可以设置469电机保护系统GEGridSolutions.com 5,根据信号阈值发出跳闸或报警命令。使用469中可用的四个可配置模拟输出,向本地监控设备提供标准传感器信号。订购继电器时,必须指定所需的输出信号,4-20 mA或0-1 mA。模拟输出可配置为基于任何测量的模拟值或任何计算的量提供输出。输出继电器469中有六个C型输出继电器。四个继电器始终是非故障安全的,可以选择性地分配执行跳闸或报警功能。还提供了一个非故障安全闭锁启动继电器,由需要闭锁功能的保护功能控制。通过故障保护服务继电器指示失去控制电源或469个内部故障。跳闸和报警继电器也可以配置闭锁功能。监控和计量469包括所有交流信号的高精度计量和记录。电压、电流、RTD和功率计量作为标准功能内置在继电器中。计量准确计量并显示以下系统值:•相位、差动和接地电流、平均电流、电机负载、电流不平衡。• Undervoltage Autorestart (Optional) • Broken rotor bar detection system (Optional) • VT Fuse Failure Inputs and Outputs Current and Voltage Inputs The 469 has two sets of three phase CT inputs, one for phase current, and one dedicated for differential protection. The ratings of the phase current inputs (1A and 5A) must be specified when ordering the relay, while the ratings for differential inputs are field programmable, supporting both 1A and 5A secondary currents. There are also 2 single-phase ground CT inputs: A standard input with settable secondary rating; 5A or 1A, and a high sensitivity ground current detection input for high resistance grounded systems. Three phase VT inputs support delta and wye configuration and provide voltage signals for all voltage, frequency and power based protection elements and metering. Digital Inputs The 469 has 5 predefined inputs: • Starter Status • Emergency Restart • Remote Reset • Setpoint Access • Test Switch The 469 also has four assignable digital inputs, which can be configured as the following functions: • Remote Trip and Alarm • Speed Switch Trip and Tachometer • Vibration Switch Trip and Alarm • Pressure Switch Trip and Alarm • Load Shed Trip • Universal Digital Counter • External oscillography trigger and External Relay Fault Simulation initiation • General Switch with programmable functions and outputs Analog Inputs and Outputs Use the four configurable analog inputs available in the 469 to measure motor operation related quantities fed to the relay from standard transducers. Each input can be individually set to measure 4-20 mA, 0-20 mA or 0-1 mA transducer signals. The 469 can also 469 Motor Protection System GEGridSolutions.com 5 be set to issue trip or alarm commands based on signal thresholds. Use the four configurable analog outputs available in the 469 to provide standard transducer signals to local monitoring equipment. The desired output signal must be specified when the relay is ordered, either 4-20 mA, or 0-1 mA. The analog outputs can be configured to provide outputs based on any measured analog value, or any calculated quantity. Output Relays There are six Form-C output relays available in the 469. Four relays are always non-failsafe and can be selectively assigned to perform trip, or alarm functions. A non-failsafe block start relay is also provided, controlled by protection functions requiring blocking functionality. Loss of control power or 469 internal failures are indicated via the failsafe service relay. The trip and alarm relays can also be configured with latching functionality. Monitoring and Metering The 469 includes high accuracy metering and recording for all AC signals. Voltage, current, RTD and power metering are built into the relay as a standard feature. Metering The following system values are accurately metered and displayed: • Phase, differential and ground currents, average current, motor load, current unbalance.