IS200EDEXG1B库存备件,工业备件
使用本产品时，请详细阅读本手册。EW200工业蜂窝网关10 1.2内容列表1.2.1包装内容#标准包装项目描述内容数量1 EW200工业移动网关1个2个8针接线板1个3个4针接线板4个DIN导轨支架1个EW200工业无线网关11 1.3硬件配置✓前视图※重置按钮重置按钮提供了快速简便的方式恢复默认设置。连续按下重置按钮6秒，然后松开。设备将重置为出厂默认设置。※3G/4G，Wi-Fi天线所有3G/4G和2.4G/5GHz Wi-Fi天线都是可选配件，不包含在标准套餐中。购买合适的天线和所需的射频电缆以适合您的应用。LED指示灯自动MDI/MDIX RJ45端口4x Gb LAN自动MDI/MD IX RJ45端口1x Gb可配置WAN 3G/4G天线2.4G/5GHz Wi-Fi天线。SIM A插槽SIM B插槽串行端口重置按钮USB端口EW200工业蜂窝网关12Ö左视图DI/DO端子块DC电源端子块接地螺钉EW200工业移动网关13 1.4 LED指示灯LED图标指示LED颜色描述电源1蓝色稳定开启：设备由电源供电1电源2蓝色稳定开启源2 Wi-Fi Wi-Fi 2.4G/5GHz蓝色关闭：Wi-Fi已禁用稳定打开：Wi-Fi已启用信号信号（蜂窝）蓝色稳定打开：信号强度为61~100%慢速闪烁（每秒）：信号强度是31~60%快速闪烁（每秒0.5秒）：信号强度为0~30%WAN WAN（蜂窝）绿色关闭：通过蜂窝接口传输数据包闪烁：通过蜂窝传输数据包接口LAN 1~LAN 4/WAN绿色稳定：建立LAN或WAN的以太网连接。闪存：正在传输数据包。关闭：连接以太网电缆或连接设备t。串行串行蓝色关闭：通过串行端口传输的串行数据闪烁：通过串行接口传输的数据包状态蓝色慢速闪烁（每秒）：设备正常工作非常快速闪烁：设备处于恢复模式或异常状态SIM A/B蓝色关闭：SIM检测到慢速闪烁（每秒钟）：已选择SIM A/B用于连接稳定打开：蜂窝连接已成功建立（在SIM A/B下）EW200工业蜂窝网关14 1.5安装和维护1.5.1系统要求网络要求千兆以太网RJ45电缆3G/4G蜂窝服务订阅IEEE 802.11 A/B/g/c无线客户端10/100/1000以太网适配器基于PC的网络配置实用程序要求计算机具有以下功能：Windows®、Macintosh、，或基于Linux的操作系统已安装以太网适配器浏览器要求：Internet Explorer 6.0或更高版本Chrome 2.0或更高浏览器3.0或更高Safari 3.0或更高级1.5.2警告l仅使用符合网关电源规格的电源。使用不符合规范的额定电压电源是危险的，可能会损坏产品。我不要自己打开或修理箱子。如果产品过热，请立即关闭电源，并在合格的服务中心进行维修。注意EW200工业蜂窝网关15 1.5.3高温表面小心：金属外壳的表面温度可能非常高！特别是在长时间运行后，当安装在没有空调的封闭机柜中或环境温度较高的位置时。不要触摸热表面！！EW200工业蜂窝网关16 1.5.4 CE RED要求的产品信息以下产品信息需要在产品用户手册中提供，以满足最新的CE RED需求。1（1）频带和功率1.蜂窝连接频带数工作频率最大输出功率GHz 100 mW 5G 5.15–5.25 GHz 200 mW（2）5150 ~ 5350MHz室内使用声明本产品配备符合IEEE 802.11ac的5GHz无线无线电模块。根据RED要求，5150~5350 MHz频带中覆盖的信道仅供室内使用。1本节中提供的信息仅适用于欧盟/欧洲自由贸易联盟地区版本。对于n-CE/EFTA版本，请参考相应的产品规范。EW200工业蜂窝网关17（3）国家限制列表（适用于带5GHz无线电的产品）对于EU/EFTA，该产品可用于所有欧盟成员国和EFTA国家。在BE BG CH CY CY DK DE EE EL ES FI FR HR HU IE IT LT LU LV MT NL PL PT RO SI SK SE TR UK（4）RF暴露声明在正常使用条件下，产品的天线应与用户身体至少相距20 cm。（5） 单元安装说明该产品适用于在高空安装WAN>物理接口选项卡。物理接口允许设置物理WAN接口并调整WAN的行为。te：可用WAN接口的数量因型号而异。当Ed
and use this product, please read this manual in detail. EW200 Industrial Cellular Gateway 10 1.2 Contents List 1.2.1 Package Contents #Standard Package Items Description Contents Quantity 1 EW200 Industrial Cellular Gateway 1pcs 2 8 pin Terminal Block 1pcs 3 4 pin Terminal Block 1pcs 4 DIN-Rail Bracket 1pcs EW200 Industrial Cellular Gateway 11 1.3 Hardware Configuration Ø Front View ※Reset Button The RESET button provides a quick and easy way to restore the default settings. Press the RESET button continuously for 6 seconds, and then release it. The device will reset to factory default settings. ※ 3G/4G, Wi-Fi Antenna All the 3G/4G and 2.4G/5GHz Wi-Fi antennas are optional accessories, and are t included in the standard package. Purchase suitable antennas and required RF cables to fit your application. LED Indicators Auto MDI/MDIX RJ45 Ports 4x Gb LAN Auto MDI/MDIX RJ45 Port 1x Gb Configurable WAN 3G/4G Antenna 2.4G/5GHz Wi-Fi Ant. SIM A Slot SIM B Slot Serial Port Reset Button USB Port EW200 Industrial Cellular Gateway 12 Ø Left View DI/DO Terminal Block DC Power Terminal Block Earth Ground Screw EW200 Industrial Cellular Gateway 13 1.4 LED Indicators LED Icon Indication LED Color Description Power Source 1 Blue Steady ON: Device is powered on by power source 1 Power Source 2 Blue Steady ON: Device is powered on by power source 2 Wi-Fi Wi-Fi 2.4G/5GHz Blue OFF: Wi-Fi is disabled Steady ON: Wi-Fi is enabled Signal Signal (Cellular) Blue Steady On: Signal Strength is 61~100% Slow Flash (per Second): Signal Strength is 31~60% Fast Flash (per 0.5 second): Signal Strength is 0~30% WAN WAN (Cellular) Blue OFF: data packets transferred via Cellular interface Flashing: Data packets being transferred via Cellular interface LAN 1 ~ LAN 4/WAN Green Steady ON: Ethernet connection of LAN or WAN is established. Flash: Data packets are being transferred. OFF: Ethernet cable attached or Device t linked. Serial Serial Blue OFF: Serial data transferred via serial port Flashing: Data packets being transferred via Serial port Status Status Blue Slow Flash (per Second): Device working rmally Very Fast Flash: Device is in Recovery Mode or abrmal state SIM A/B Blue OFF: SIM t detected Slow Flash (per Second): SIM A/B was chosen for the connection Steady ON: Cellular connection successfully established (under SIM A/B) EW200 Industrial Cellular Gateway 14 1.5 Installation & Maintenance 1.5.1 SYSTEM REQUIREMENTS Network Requirements A gigabit Ethernet RJ45 cable 3G/4G cellular service subscription IEEE 802.11 a/b/g/c wireless clients 10/100/1000 Ethernet adapter on PC Web-based Configuration Utility Requirements Computer with the following: Windows®, Macintosh, or Linux-based operating system An installed Ethernet adapter Browser Requirements: Internet Explorer 6.0 or higher Chrome 2.0 or higher Firefox 3.0 or higher Safari 3.0 or higher 1.5.2 WARNING l Only use the power supply that complies with the power specification of the gateway. Using an out-of-spec voltage rating power source is dangerous and may damage the product. l Do t open or repair the case yourself. If the product is too hot, turn off the power immediately and have it repaired at a qualified service center. Attention EW200 Industrial Cellular Gateway 15 1.5.3 HOT SURFACE CAUTION CAUTION: The surface temperature for the metallic enclosure can be very high! Especially after long periods of operation, when installed in a closed cabinet without air conditioning, or in a location with a high ambient temperature. DO T touch the hot surface!! EW200 Industrial Cellular Gateway 16 1.5.4 Product Information for CE RED Requirements The following product information is required to be presented in product User Manual for latest CE RED requirements. 1 (1) Frequency Band & Power 1.a Frequency Band for Cellular Connection Band number Operating Frequency Max output power GHz 100 mW 5G 5.15 – 5.25 GHz 200 mW (2) 5150 ~ 5350MHz Indoor Use Statements This product is equipped with IEEE 802.11ac compliant 5GHz wireless radio module. According to RED requirements, the channels covered in the 5150 ~ 5350 MHz frequency band are for Indoor Use Only. 1 The information presented in this section is ONLY valid for the EU/EFTA regional version. For n-CE/EFTA versions, please refer to the corresponding product specification. EW200 Industrial Cellular Gateway 17 (3) Country List for Restrictions (for products with 5GHz radio) For EU/EFTA, this product can be used in all EU member states and EFTA countries. AT BE BG CH CY CY DK DE EE EL ES FI FR HR HU IE IT LT LU LV MT NL PL PT RO SI SK SE TR UK (4) RF Exposure Statements The antenna of the product, under rmal use condition, should be at least 20 cm away from the body of user. (5) Unit Mounting tice The product is suitable for mounting at heights WAN > Physical Interface tab. The Physical Interface allows for the setup of the physical WAN interface and adjustment of WAN’s behavior. te: Number of available WAN Interfaces varies by model. When the Edit button is applied, an Interface Configuration screen will appear. WAN-1 interface is used in this example.
