IS200EPDMG1BAA DCS工控模块备件
（1066米），153.6 Kbaud扩展；153.6 Kbaud扩展；153.6 Kbaud扩展；2000英尺（609米），2000英尺（608米）。153.6 Kbaud标准。153.6 Kbaud标准。每个波特率长度每个波特率长度也取决于电缆类型。也取决于电缆类型。也取决于电缆类型。PC电源要求5 VDC、600mA 5 VDC、400mA 5 VDC和400mA机械PCI插槽，电路板尺寸为单插槽AT全长单插槽AT总长6.875“x 4.2”（标准PCI短卡）。背板要求PCI Genius（PCGEN）卡兼容主板-4字节主板-4字节与PC兼容计算机具有PCI每个通道-16KB共享每个通道-16Kbytes共享插槽，符合外围RAM内存RAM内存组件互连总线规范可配置中断可配置中断v2.2，并且还与PCI v2.1 Artisan技术组-质量仪器。。。保证214 GE Fanuc控制器和I/O解决方案附件和电缆IC660BSM021 Genius总线开关模块、24/48 VDC IC660BSM120 Genius总线切换模块、，115 VAC/125 VDC IC660BLC001 Genius总线电缆，带连接器Alpha 9823 15 In（数量3）IC660BLC-03 Genius总线线缆，带连接器阿尔法9823 3 Ft IC660BLM506总线终端150 Ohm（数量4）IC660BL M508总线终端75 Ohm（量4）IC660 BLM507 Genius块拉拔器手持式监视器IC660HHM501手持式监视器可用于控制和排除Genius块。套件包括电缆和电池充电器IC660BCM501手持式显示器电池充电器IC660 BPM500手持式显示器电池组Genius Artisan技术组-质量仪表。。。保证GE Fanuc控制器和I/O解决方案215配置指南配置Genius网络时，应考虑以下指南1。Genius LAN限制为32个设备。请记住，Genius总线控制器保留一个地址，如果使用了手持式配置器，它也保留了一个地址。2.如果应用需要冗余网络，则需要总线交换模块（IC660BSMxxx）。3.需要在每个网络（IC660BLM50x）4的末端终止。对于4500英尺以外的长距离，设备数量限制为16个。电缆选择电缆#外部终端电阻器*介质环境长度电缆运行数量和制造直径-10%至+20%导线/电压温度英尺/米，波特率1/2瓦AWG额定值配置，用于控制器（示例应用需要（120）24 VDC输入和（80）继电器输出AC电源），用于本地控制。系统还具有五个远程机柜，每个机柜需要（64）24 VDC输入、（21）24 VDC 0.5安培、电源输出和（2）电流输入
(1066 meters) at 153.6 Kbaud extended; 153.6 Kbaud extended; 153.6 Kbaud extended; 2000 feet (609 meters) at 2000 feet (609 meters) at 2000 feet (609 meters) at 153.6 Kbaud standard. 153.6 Kbaud standard. 153.6 Kbaud standard. length at each baud rate length at each baud rate length at each baud rate also depends on cable type. also depends on cable type. also depends on cable type. PC Power Requirement 5 VDC, 600mA 5 VDC, 400mA 5 VDC, 400mA Mechanical PCI Slot, dimensions of board are Single Slot AT full Length Single Slot AT full Length 6.875” x 4.2” (Standard PCI short Card). Backplane Requirements The PCI Genius (PCGEN) card is compatible Motherboard - 4 bytes Motherboard - 4 bytes with PC Compatible computers having a PCI Each channel - 16Kbytes shared Each channel - 16Kbytes shared slot which is compliant with the Peripheral RAM Memory RAM Memory Component Interconnect Bus Specification Configurable Interrupts Configurable Interrupts v2.2, and also works with PCI v2.1 Artisan Techlogy Group - Quality Instrumentation ... Guaranteed 214 GE Fanuc Controller and I/O Solutions Accessories and Cables IC660BSM021 Genius Bus Switching Module, 24/48 VDC IC660BSM120 Genius Bus Switching Module, 115 VAC/125 VDC IC660BLC001 Genius bus Cable w/Connectors Alpha 9823 15 In (Qty 3) IC660BLC003 Genius bus Cable w/Connectors Alpha 9823 3 Ft IC660BLM506 Bus Terminator 150 Ohm (Qty 4) IC660BLM508 Bus Terminator 75 Ohm (Qty 4) IC660BLM507 Genius Block Puller Hand Held Monitor IC660HHM501 Hand-Held Monitor can be used to con and trouble shoot Genius blocks. Kit includes Cable and Battery Charger IC660BCM501 Hand-Held Monitor Battery Charger IC660BPM500 Hand-Held Monitor Battery Pack Genius Artisan Techlogy Group - Quality Instrumentation ... Guaranteed GE Fanuc Controller and I/O Solutions 215 Configuration Guidelines When configuring a Genius network the following guidelines should be considered 1. Genius LAN is limited to 32 devices. Remember that the Genius Bus Controller reserves one address and if a Hand-Held configurator is used, it also reserves an address. 2. If the application requires redundant networks, a Bus Switching Module is required (IC660BSMxxx). 3. Termination is required at the end of each network (IC660BLM50x) 4. For long distances, beyond 4,500 feet, the number of devices is limited to 16. Cable Selection Cable # Outer Terminating Resistor* Number of Dielectric Ambient Length Cable Run, & Make Diameter -10% to +20% Conductors/ Voltage Temp feet/meters at baudrate 1/2 Watt AWG Rating Rating Configuration for Controller (Example application requiring (120) 24 VDC inputs and (80) Relay outputs AC power supply) for local control. System also has five remote cabinets, with each cabinet requiring (64) 24 VDC Inputs, (21) 24 VDC 0.5 Amp, Source Outputs and (2) current inputs
