IS200FOSBH1A工控模块机器人备件
您也不能在同一系统中安装EICM和TCM。COM插槽COM插槽只能用于TCM、EICM或NCM。TCM最多可为TCM配置两个逻辑插槽。匹配的成对TCM可以安装在每个逻辑插槽的左侧和右侧位置，它们可以位于主机箱或机箱2中。4351A、4351B、4352A和4352B型TCM不能安装在具有4351或4352型TCM的系统中，即使它们安装在不同的底盘中。NCM最多可为NCM配置两个逻辑插槽。匹配的NCM对可以安装在每个逻辑插槽的左侧和右侧位置。如果仅使用一个逻辑插槽，则该插槽可以位于主机箱或机箱2中。如果使用两个逻辑插槽，则它们必须是主机箱中的插槽6和7，并且不能使用对等。EICM和ACM一个逻辑插槽可分别用于EICM或ACM。这些模块的配对可以安装在一个逻辑插槽的左侧和右侧位置。HIM最多可为HIM配置两个逻辑插槽。两个插槽必须位于主机箱中。SMM最多可为SMM配置三个逻辑插槽。一对匹配的SMM可以安装在每个逻辑插槽的左侧和右侧位置。所有三个插槽必须位于主机箱或机箱2中。166第3章Tricon v9–v10系统的安装和维护规划与安装指南Tricon系统的电源规划Tricon电源模块为大多数控制器配置提供了充分的支持，但是，由于这些模块比其他模块消耗更多的功率，因此限制可能适用于包含多个通信模块的主机箱。本节介绍如何确定Tricon控制器的逻辑功耗和冷却要求。本节中的数据基于只有一个冗余电源模块工作的故障情况。在正常工作条件下，两个电源模块共享负载。确定Tricon控制器机箱的逻辑电源逻辑电源是指机箱的电源模块在不过载的情况下可以支持的模块数量和类型。表70（第167页）确定了每个模块的逻辑功率。总功率不能超过175瓦，因为每个功率模块在140°F（60°C）的额定最高温度下最多可提供175瓦的功率。该计算基于以下假设：只有一个冗余电源模块可运行。在正常工作条件下，两个电源模块共享负载，并在所有温度下提供更多的电源。这种负载共享允许功率模块正常运行时低于其额定最大输出的50%，从而显著延长其使用寿命。要确定逻辑功率，请添加：•主模块的逻辑功率•热备用模块的逻辑电源警告不要在位于危险位置且必须符合ATEX要求的Tricon系统中使用8312型电源模块。如果您的线路电压为230 V，并且您的系统必须符合ATEX要求，请使用8311型24 VDC电源模块以及菲尼克斯电气（Phoenix Contact）的ATEX认证24 VDC电源，零件号为QUINT-PS100-240AC/24DC/10/EX。小心避免将多个高功率I/O模块放入主机箱。每个主机箱必须包含三个主处理器和一个通信模块，这意味着多个高功率I/O模块可能超过逻辑功率限制。系统配置167规划和安装
You also cannot install an EICM and a TCM in the same system. COM Slot The COM slot can only be used for a TCM, EICM, or NCM. TCM Up to two logical slots can be configured for TCMs. Matched pairs of TCMs can be installed in the left and right positions of each logical slot, and they can be located in the main chassis or Chassis 2. Model 4351A, 4351B, 4352A, and 4352B TCMs cannot be installed into a system with model 4351 or 4352 TCMs, even if they are installed in different chassis. NCM Up to two logical slots can be configured for NCMs. Matched pairs of NCMs can be installed in the left and right positions of each logical slot. If only one logical slot is used, the slot can be in the Main Chassis or Chassis 2. If two logical slots are used, they must be Slot 6 and 7 in the Main Chassis, and Peer to Peer cannot be used. EICM and ACM One logical slot is available for EICMs or ACMs, respectively. Matched pairs of these modules can be installed in both the left and right positions of one logical slot. HIM Up to two logical slots can be configured for HIMs. Both slots must be in the Main Chassis. SMM Up to three logical slots can be configured for SMMs. A matched pair of SMMs can be installed in the left and right positions of each logical slot. All three slots must be in the Main Chassis or Chassis 2. 166 Chapter 3 Installation and Maintenance Planning and Installation Guide for Tricon v9–v10 Systems Planning Power for a Tricon System The Tricon Power Modules provide adequate support for most controller configurations, however, limitations may apply to a Main Chassis containing multiple communication modules because these modules consume more power than others. This section explains how to determine the logic power consumption and cooling requirements of a Tricon controller. Data in this section is based on a fault condition where only one of the redundant Power Modules is operational. Under normal operating conditions, both Power Modules share the load. Determining Logic Power for Tricon Controller Chassis Logic power refers to the number and kinds of modules that the Power Modules of a chassis can support without being overloaded. Table 70 (on page 167) identifies the logic power for each module. The total cannot exceed 175 watts, because each Power Module supplies a maximum of 175 watts at the rated maximum temperature of 140° F (60° C). This calculation is based on the assumption that only one of the redundant Power Modules is operational. Under normal operating conditions, both Power Modules share the load and make more power available at all temperatures. This load-sharing allows the Power Modules to normally run at less than 50 percent of their rated maximum output thereby significantly increasing their service lifetime. To determine logic power, add: • logic power for primary modules • logic power for hot-spare modules WARNING Do not use the model 8312 Power Module in Tricon systems that are located in hazardous locations and must meet ATEX requirements. If you have 230 V line voltage and your system must meet ATEX requirements, use the model 8311 24 VDC Power Module along with the ATEX-certified 24 VDC power supply from Phoenix Contact—part number QUINT-PS100-240AC/24DC/10/EX. CAUTION Avoid putting multiple high-power I/O modules into a Main Chassis. Each Main Chassis must house three Main Processors and a communication module which means multiple high-power I/O modules could exceed logic power limitations. System Configuration 167 Planning and Installation
