IS200GDDDG1AAA工控模块系统备件
Rdy状态指示灯：端口活动UCN A，UCN端口A活动UCN B，UCN Port B活动状态指示灯SMM传输Xmit状态指示灯模块节点和诊断信息状态逻辑功率<20瓦隔离（所有端口）500 VDC数据库内存电池备份6个月，典型Tricon通信模块（TCM）159 Tricon v9–v10系统Tricon通信组件（TCM）规划和安装指南单个Tricon系统最多支持四个TCM，这些TCM必须位于机箱1或机箱2中的两个逻辑插槽中。不同的TCM型号不能混合在一个逻辑中。Tricon通信模块（TCM）仅与Tricon v10.0和更高版本的系统兼容，允许Tricon通过以太网与TriStation、其他Tricon或Trident控制器、Modbus主设备和从设备以及外部主机进行通信。每个TCM包含四个串行端口、两个网络端口和一个调试端口（用于Triconex）。每个串行端口都有唯一的地址，可以配置为Modbus主端口或从端口。串行端口1支持Modbus或Trimble GPS接口。串行端口4支持Modbus或TriStation接口。对于所有四个串行端口，每个TCM支持460.8千位/秒的聚合数据速率。Tricon的程序使用变量名作为标识符，但Modbus设备使用称为别名的数字地址。因此，必须为Modbus设备读取或写入的每个Tricon变量名分配别名。别名是一个五位数字，代表Modbus消息类型和Tricon中变量的地址。TriStation中分配了别名。只要为Tricon变量分配别名，任何标准Modbus设备都可以通过TCM与Tricon通信。当主机通过其他通信模块（如NCM）访问Tricon时，还必须使用别名。TCM型号4353和4354具有嵌入式OPC服务器，允许多达10个OPC客户端订阅OPC服务器收集的数据。嵌入式OPC服务器支持数据访问标准和报警和事件标准。每个TCM包含两个网络端口NET 1和NET 2。4351、4351A、4351B和4353型具有两个铜质以太网端口。4352、4352A、4352B和4354型具有两个光纤以太网端口。TCM网络端口上支持的协议列表见表67。图70 TCM前面板PASS FAULT ACTIVE FIRM NET 1 LINK TX RX NET 2 LINK TX RX SERIAL 1 TX RX SERIAL 2 TX RX DEBUG TX RX SERAL 3 SERIAL 4 TX RX 435x TCM NET 1（铜或光纤以太网）NET 2（铜或纤维以太网）串行端口#1用于GPS或Modbus接口串行端口#2用于Modbus接口串行口#3用于Modbus接口串口#4用于TriStation或Modbus接口调试端口对于Triconex，请使用160第2章《Tricon v9–v10系统插槽系统组件规划和安装指南》。每个Tricon系统总共支持16个Modbus主设备或从设备，包括网络和串行端口。热备盘功能不适用于TCM，但您可以在控制器联机时更换有故障的TCM。本表描述了TCM型号和Tricon系统版本兼容性。有关更多信息，请参阅第230页的《Tricon v9–v10系统和更换TCM通信指南》。TCM规格此表列出了TCM型号或更高版本4351B、4352B、4353、4354的规格。注意：不同的TCM型号不能混合在同一逻辑插槽中。此外，4351A、4351B、4352A、4352B、4353和4354型TCM不能安装在具有4351或4352型TCM的系统中，即使它们安装在不同的机箱中。表66 TCM规格功能描述串行端口4、RS-232/RS-485端口、DB-9连接器网络端口2、10/100BaseT以太网端口、RJ-45连接器（型号4351、4351A、4351B和4353）2、光纤模式以太网端口、带62.5/125 um光纤电缆的MT-RJ连接器（型号435、4352A、4352B和4354）端口隔离500 VDC通信协议TriStation、，嵌入式OPC服务器（型号4353和4354）、Modbus、Modbus TCP、TCP/IP、SNTP、TSAA（支持IP多播）、Trimble GPS、对等、Triconex时间同步、，支持Jet Direct（网络打印）Modbus功能01-读取线圈状态06-修改寄存器内容02-读取输入状态07-读取异常状态03-读取保持寄存器08-环回诊断测试04-读取输入寄存器15-强制多个线圈05-修改线圈状态
Rdy Status indicator: Port activity UCN A, UCN Port A Active UCN B, UCN Port B Active Status indicator: SMM transmitting Xmit Status indicator: Module node and diagnostic information Status Logic power < 20 watts Isolation (all ports) 500 VDC Battery backup for database memory 6 months, typical Tricon Communication Module (TCM) 159 Planning and Installation Guide for Tricon v9–v10 Systems Tricon Communication Module (TCM) A single Tricon system supports a maximum of four TCMs, which must reside in two logical slots located in chassis 1 or chassis 2 only. Different TCM models cannot be mixed in one logical The Tricon Communication Module (TCM), which is compatible with only Tricon v10.0 and later systems, allows the Tricon to communicate with TriStation, other Tricon or Trident controllers, Modbus master and slave devices, and external hosts over Ethernet networks. Each TCM contains four serial ports, two network ports, and one debug port (for Triconex use). Each serial port is uniquely addressed and can be configured as a Modbus master or slave. Serial port 1 supports either the Modbus or the Trimble GPS interface. Serial port 4 supports either the Modbus or the TriStation interface. Each TCM supports an aggregate data rate of 460.8 kilobits per second, for all four serial ports. Programs for the Tricon use variable names as identifiers but Modbus devices use numeric addresses called aliases. Therefore an alias must be assigned to each Tricon variable name that will be read by or written to a Modbus device. An alias is a five-digit number which represents the Modbus message type and the address of the variable in the Tricon. An alias number is assigned in TriStation. Any standard Modbus device can communicate with the Tricon through the TCM, provided that aliases are assigned to the Tricon variables. Alias numbers must also be used when host computers access the Tricon through other communication modules, such as the NCM. TCM models 4353 and 4354 have an embedded OPC server, which allows up to ten OPC clients to subscribe to data collected by the OPC server. The embedded OPC server supports the Data Access standard and the Alarms and Events standard. Each TCM contains two network ports—NET 1 and NET 2. Models 4351, 4351A, 4351B, and 4353 have two copper Ethernet ports. Models 4352, 4352A, 4352B, and 4354 have two fiber-optic Ethernet ports. See Table 67 for the list of supported protocols on the TCM network ports. Figure 70 TCM Front Panel PASS FAULT ACTIVE FIRM NET 1 LINK TX RX NET 2 LINK TX RX SERIAL 1 TX RX SERIAL 2 TX RX DEBUG TX RX SERIAL 3 SERIAL 4 TX RX 435x TCM NET 1 (Copper or Fiber Ethernet) NET 2 (Copper or Fiber Ethernet) Serial Port #1 for GPS or Modbus interface Serial Port #2 for Modbus interface Serial Port #3 for Modbus interface Serial Port #4 for TriStation or Modbus interface Debug Port for Triconex use 160 Chapter 2 System Components Planning and Installation Guide for Tricon v9–v10 Systems slot. Each Tricon system supports a total of sixteen Modbus masters or slaves—this total includes network and serial ports. The hot-spare feature is not available for the TCM, though you can replace a faulty TCM while the controller is online. This table describes TCM model and Tricon system version compatibility. For additional information, see the Communication Guide for Tricon v9–v10 Systems and Replacing TCMs on page 230. TCM Specifications This table lists specifications for TCM models or later 4351B, 4352B, 4353, 4354 CAUTION Different TCM models cannot be mixed in the same logical slot. Additionally, models 4351A, 4351B, 4352A, 4352B, 4353, and 4354 TCMs cannot be installed into a system with 4351 or 4352 TCMs, even if they are installed in different chassis. Table 66 TCM Specifications Feature Description Serial ports 4, RS-232/RS-485 ports, DB-9 connectors Network ports 2, 10/100BaseT Ethernet ports, RJ-45 connectors (models 4351, 4351A, 4351B, and 4353) 2, fiber-optic mode Ethernet ports, MT-RJ connectors with 62.5/125 um fiber cables (models 4352, 4352A, 4352B, and 4354) Port isolation 500 VDC Communication protocols TriStation, Embedded OPC Server (models 4353 and 4354), Modbus, Modbus TCP, TCP/IP, SNTP, TSAA (with support for IP Multicast), Trimble GPS, Peer-to-Peer, Triconex Time Synchronization, Jet Direct (network printing) Modbus functions supported 01 — Read Coil Status 06 — Modify Register Content 02 — Read Input Status 07 — Read Exception Status 03 — Read Holding Registers 08 — Loopback Diagnostic Test 04 — Read Input Registers 15 — Force Multiple Coils 05 — Modify Coil Status
