IS200ICBDH1ABA模块控制器
@ 60 Hz至底盘的泄漏电流@60 Hz 4 mA最大@60 Hz保险丝（现场终端模块上）每个输出1个，3安培，快速动作状态指示灯：开或关状态每个点1个状态指示器：模块状态通过，故障，活动状态指示器：现场报警1 1。必须向所有点供电，包括非公用面板上未使用的点。负载/保险丝点隔离：最小3601E 1000 VAC，最小1500 VDC点隔离：最低3601T 1780 VAC，最小2500 VDC输出诊断故障范围2：最大输出切换率2。最大输出切换率可实现I/O诊断的正确操作和所有正常可检测故障的检测。最小切换率提供了模块计算平均故障间隔时间（MTBF）10%内正常不可检测故障的故障覆盖率。每100毫秒加一次扫描输出诊断故障覆盖率2：最小输出切换率每3个月诊断故障持续时间3 3。使用OVD禁用功能可以禁用诊断故障。1/2交流周期最大开态压降：在背板上，典型值<2 VAC@100mA<3 VAC最大@2A开态压降；带外部终端，10英尺电缆典型值<3 VAC@100mA<5 VAC最大@2B开态压降。带外部终端，99英尺电缆<4 VAC典型@100mA<11 VAC最大@2A感应反冲保护（反EMF）零交叉TRIAC 92第2章Tricon v9–v10系统24至120 VDC数字输出模块的系统组件规划和安装指南本图为3603B、3603E、3603T、3604E和3607E型TMR数字输出模块简化示意图。图38 3603B、3603E、3603T、3604E，和3607E简化原理图总线Xcvr点寄存器总线Xcvr点寄存器总线Xcvr点寄存器输出开关驱动电路A A和B输出开关驱动线路输出开关驱动回路B输出开关驱动器电路C A B C A和B A B C+V A B C TRIPLICATED I/O总线现场电路典型点（16）–电压环回检测器LD RTN智能I/O控制器（S）***所有输出开关都是光隔离的。其他点（仅限3603E/T）到其他点（只限3603E/T）µProcµProc数字输出模块93 Tricon v9–v10系统的规划和安装指南此图显示了3603B、3603E、3603T、3604E和3607E型号的前面板。图39 3603B、3603E、3603T、3604E和3607E前面板24 VDC 24 VDC数字输出3604E第2章Tricon v9–v10系统的系统组件规划和安装指南3603B规格本表列出了3603B型号的规格，该型号是一个标称输出电压为120 VDC的TMR数字输出模块。警告：3603B、3603E和3603T型数字输出模块不应混合在同一逻辑插槽中。表32 3603B数字输出规格特性规格颜色代码蓝色输出信号数量16，非公用最小负载要求20 kΩ，作为标准安装在所有现场终端模块上电压范围99–155 VDC电源模块负载<10瓦额定电流，最大0.8安培/点，4安培浪涌/10毫秒负载泄漏电流2 mA，最大保险丝，现场终端模块每输出1个，1安培，快速动作状态指示器：开或关状态每点1个状态指示器：模块状态通过、故障、活动状态指示器：现场警报1 1。必须向所有点供电，包括非公用面板上未使用的点。负载/保险丝点隔离1000 VDC最小输出诊断故障范围2：最大输出切换率最小输出切换率
@ 60 Hz Leakage current to chassis @ 60 Hz 4 mA maximum @ 60 Hz Fuses (on field termination module) 1 per output, 3 amps, fast-acting Status indicator: On or Off state 1 per point Status indicator: Module status Pass, Fault, Active Status indicator: Field alarm1 1. Power must be supplied to all points, including unused points on non-commoned panels. Load/fuse Point isolation: 3601E 1000 VAC minimum, 1500 VDC minimum Point isolation: 3601T 1780 VAC minimum, 2500 VDC minimum Output diagnostic fault coverage2: Maximum output toggle rate 2. The maximum output toggle rate enables proper operation of I/O diagnostics and detection of all normally detectable faults. The minimum toggle rate provides fault coverage of normally undetectable faults within 10% of the calculated mean-time-between-faults (MTBF) for the module. Every 100 ms plus one scan Output diagnostic fault coverage2: Minimum output toggle rate Every 3 months Diagnostic glitch duration3 3. Diagnostic glitching can be disabled by using the OVD disable function. 1/2 AC cycle maximum On-state voltage drop: At backplane < 2 VAC typical @ 100mA < 3 VAC maximum @ 2A On-state voltage drop: With external termination, 10-foot cable < 3 VAC typical @ 100mA < 5 VAC maximum @ 2A On-state voltage drop: With external termination, 99-foot cable < 4 VAC typical @ 100mA < 11 VAC maximum @ 2A Inductive kick-back protection (reverse EMF) Zero-crossing TRIACs 92 Chapter 2 System Components Planning and Installation Guide for Tricon v9–v10 Systems 24 to 120 VDC Digital Output Modules This figure is a simplified schematic for models 3603B, 3603E, 3603T, 3604E, and 3607E, which are TMR Digital Output Modules. Figure 38 3603B, 3603E, 3603T, 3604E, and 3607E Simplified Schematic Bus Xcvr Point Register Bus Xcvr Point Register Bus Xcvr Point Register Output Switch Drive Circuitry A A and B Output Switch Drive Circuitry Output Switch Drive Circuitry B Output Switch Drive Circuitry C A B C A and B A B C +V A B C TRIPLICATED I/O BUS FIELD CIRCUITRY TYPICAL POINT (16) – Voltage Loopback Detector LD RTN INTELLIGENT I/O CONTROLLER(S) * * * * * All output switches are opto-isolated. to other points (3603E/T only) to other points (3603E/T only) µProc µProc µProc Digital Output Modules 93 Planning and Installation Guide for Tricon v9–v10 Systems This figure shows the front panels of models 3603B, 3603E, 3603T, 3604E, and 3607E. Figure 39 3603B, 3603E, 3603T, 3604E, and 3607E Front Panels 24 VDC 24 VDC DIGITAL OUTPUT 3604E Chapter 2 System Components Planning and Installation Guide for Tricon v9–v10 Systems 3603B Specifications This table lists the specifications for model 3603B which is a TMR Digital Output Module with a nominal output voltage of 120 VDC. CAUTION Model 3603B, 3603E, and 3603T Digital Output Modules should not be mixed in the same logical slot. Table 32 3603B Digital Output Specifications Feature Specification Color code Blue Number of output signals 16, non- commoned Minimum load required 20 kΩ, installed as standard on all field termination modules Voltage range 99–155 VDC Power module load < 10 watts Current ratings, maximum 0.8 amps/point, 4 amps surge/10 ms Leakage current to load 2 mA, maximum Fuses, field termination module 1 per output, 1 amp, fast-acting Status indicator: On or Off state 1 per point Status indicator: Module status Pass, Fault, Active Status indicator: Field alarm1 1. Power must be supplied to all points, including unused points on non-commoned panels. Load/Fuse Point isolation 1000 VDC minimum Output diagnostic fault coverage2: Maximum output toggle rate Minimum output toggle rate
