IS200ISBDG1AAA/IS200DAMDG2AAA通用电气卡件
辐射发射CISPR 11，A级，30-1000 MHz@10m，4-47 db，当根据本手册中的指南安装时。概述25 Tricon v9–v10系统电厂的规划和安装指南，以及IEEE 344，核电站1E级设备抗震鉴定的推荐规程。有关符合1E级应用的型号和版本的详细信息，请联系英维思核电公司。电话免费电话：866-703-6300，或收费电话：949-885-0885网站www.invensysnucler.com部件典型重量本表列出了部件的典型重量。接地系统Tricon控制器包括三个单独的接地系统：•保护接地-交流安全接地或底盘接地•信号或仪表接地-功能接地•屏蔽接地–功能接地每个模块的数字和模拟部分使用单独和隔离的信号返回路径，这些路径连接在一起形成Tricon控制器信号接地。Tricon控制器的底盘接地（金属板）充当数字和模拟电路的静电屏蔽。（所有通信电缆屏蔽端接至机箱接地。）有关安装程序，请参阅第208页的控制器接地。表2 Tricon组件组件的重量主要或扩展机箱（未安装模块）的近似重量54.0磅（24.5千克）主处理器4.7磅（2.1千克）电源模块7.2磅（3.3千克）输入/输出模块4.75磅（2.1至2.7千克）通信模块5.0磅（2.3千克）16点终端面板.09磅（.04千克）32点终端面板2.1磅（.95千克）典型负载机箱160磅（72.6千克）-平均26第2章Tricon v9–v10系统主机箱系统组件规划和安装指南Tricon主机箱（型号8110）包括两个电源模块、三个主处理器、一个电池、一个没有热备用插槽的通信（COM）插槽以及六个用于I/O和通信模块的逻辑插槽。每个逻辑插槽为模块提供两个物理空间。有关安装信息，请参阅第178页的机箱和模块安装。图7典型的Tricon v10.x主机箱E C D F G M IJ K L A B A。内存备用电池B。终端连接器C。I/O扩展端口D。电源端子E。钥匙开关F。冗余电源模块G。三个主处理器H。COM插槽（空）I。两个TCM J。DI模块，不带备用K。DO模块，带热备用M。AI模块，带备用M。无备用H主机箱的AO模块27 Tricon v9–v10系统规划和安装指南图8典型Tricon v8主机箱主机箱电池Tricon控制器双冗余电池在控制器完全断电时提供内存备份。（Expansion和RXM机箱的背板不包括电池。）在没有现场电源的情况下，单个电池可以维持《Tricon v9–v10系统主处理器第2章系统组件规划和安装指南》中的控制程序。如果发生完全电源故障，这些锂电池可以在六个月的累积时间内维护数据和程序。每个电池的保质期为8-10年。Triconex建议每8-10年或使用6个月后更换一次电池，以先到者为准。如果电源模块上的BAT LOW（电池电量低）指示灯亮起，则表示应更换电池。有关说明，请参阅第217页的更换主机箱电池。Tricon控制器钥匙开关钥匙开关是位于电源模块上方的四位开关，用于确定Tricon控制器上可执行的操作类型。
Radiated Emissions CISPR 11, Class A, 30-1000 MHz @ 10m, 4-47 db when installed according to the guidelines in this manual. Overview 25 Planning and Installation Guide for Tricon v9–v10 Systems Power Plants, and IEEE 344, Recommended Practice for Seismic Qualification of Class 1E Equipment for Nuclear Power Generating Stations. For details on models and revisions qualified for 1E applications, please contact Invensys Nuclear. Telephone Toll-free number 866-703-6300, or Toll number 949-885-0885 Web Site www.invensysnuclear.com Typical Weight of Components This table identifies the typical weight of components. Ground Systems The Tricon controller includes three separate ground systems: • Protective earth —an AC safety or chassis ground • Signal or instrument ground —a functional earth • Shield ground —a functional earth The digital and analog portions of each module use separate and isolated signal return paths which are connected together to form the Tricon controller signal ground. The chassis ground (sheet metal) of the Tricon controller acts as an electrostatic shield for the digital and analog circuitry. (All communication cable shields are terminated to the chassis ground.) For installation procedures, see Controller Grounding on page 208. Table 2 Weight of Tricon Components Component Approximate Weight Main or Expansion Chassis (with no modules installed) 54.0 lbs. (24.5 kg.) Main Processor 4.7 lbs. (2.1 kg.) Power Module 7.2 lbs. (3.3 kg.) I/O Module 4.75 lbs. (2.1 kg. to 2.7 kg.) Communication Module 5.0 lbs. (2.3 kg.) 16-point Termination Panel .09 lbs. (.04 kg.) 32-point Termination Panel 2.1 lbs. (.95 kg.) Typical Loaded Chassis 160 lbs. (72.6 kg.)—average 26 Chapter 2 System Components Planning and Installation Guide for Tricon v9–v10 Systems Main Chassis A Tricon Main Chassis (model 8110) includes two Power Modules, three Main Processors, a battery, one communication (COM) slot with no hot-spare slot, and six logical slots for I/O and communication modules. Each logical slot provides two physical spaces for modules. For installation information, see Chassis and Module Installation on page 178. Figure 7 Typical Tricon v10.x Main Chassis E C D F G M IJ K L A B A. Memory backup battery B. Connectors for terminations C. I/O expansion ports D. Power terminals E. Keyswitch F. Redundant power modules G. Three main processors H. COM slot (empty) I. Two TCMs J. DI module without spare K. DO module with hot-spare L. AI module with hot-spare M. AO module without spare H Main Chassis 27 Planning and Installation Guide for Tricon v9–v10 Systems Figure 8 Typical Tricon v9 Main Chassis Main Chassis Batteries The Tricon controller dual-redundant batteries provide memory backup in case of a complete power failure of the controller. (The backplanes of Expansion and RXM Chassis do not include batteries.) In the absence of field power, a sole battery can sustain the control program in the Main Processor Chapter 2 System Components Planning and Installation Guide for Tricon v9–v10 Systems If a total power failure occurs, these lithium batteries can maintain data and programs for a cumulative time period of six months. Each battery has a shelf-life of 8-10 years. Triconex recommends that the batteries be replaced either every 8-10 years or after they accumulate 6 months of use, whichever comes first. If the BAT LOW (battery low) indicator on the Power Modules is on, it indicates the battery should be replaced. For instructions, see Replacing the Main Chassis Batteries on page 217. Tricon Controller Keyswitch The keyswitch is a four-position switch located above the Power Modules that determines the type of operations that can be taken on the Tricon controller.
