IS200ISBEH2A处理器模块
19•第20页上的欧盟CE标志加拿大标准协会（CSA）CSA已证明Tricon控制器完全符合以下国际公认的电气安全标准，并且符合北美和其他要求遵守这些标准的司法管辖区的通用要求。Factory Mutual FM已认证Tricon控制器完全符合以下国际公认标准，并有资格在I级2区温度T4、A、B、C和D组危险室内（或NEMA 4机柜室外）场所使用。对于危险位置应用，请参阅第3章“安装和维护”，了解特定应用的安装说明。标准编号标题CAN/CSA-C22.2 No.0-M91《加拿大电气规范》第二部分CSA标准C22.2 No.0.4-M1982《电气设备的连接和接地（保护接地）》CSA标准C22.2No.142-M1987《过程控制设备》UL标准508《工业控制设备》标准编号标题3611《I类2类电气设备》；II类2类；和III类第1和2部分，危险场所3810电气和电子测试，测量和过程控制设备3600 3600危险（分类）场所使用的电气设备一般要求18第1章Tricon v9–v10 Systems TÜV Rheinland/Berlin Brandenburg TÜV简介规划和安装指南已证明Tricon控制器完全符合下列国际公认标准，因此有资格在以下应用和司法管辖区使用根据IEC 61508的功能安全要求，紧急安全停机或其他需要SIL 1-3认证的关键控制应用（仅Tricon v9.6或更高版本）•根据DIN V 19250和DIN V VDE 0801的功能安全需求，紧急安全停车或其他需要AK 1-AK6认证的关键控制应用（仅Tricon v9.x）•火灾和气体检测需要根据EN 54要求认证的应用•需要根据NFPA 72要求认证的火灾和气体探测应用（仅Tricon v9.6或更高版本）•需要根据DIN VDE 0116要求认证的燃烧器管理应用•需要按照NFPA 8501或NFPA 8502要求认证的燃烧器管理应用（仅限Tricon v9.6或更高版本）•在欧盟或其他司法管辖区使用的所有应用程序，要求符合第89/336/EEC号EMC指令和第72/23/EEC号低压设备指令•在欧盟和其他司法管辖区域使用的所有应用程序，要求遵守第94/9/EC号ATEX指令，适用于2区IIB组危险场所•环境、，根据SEMI S2（仅Tricon v9.4）标准编号标题IEC 61508第1-7部分的要求，2000（仅Tricon v9.6或更高版本）电气/电子/可编程电子安全相关系统的功能安全DIN V 19250/05:94（仅Trion v9.x）测量和控制保护设备应考虑的基本安全方面DIN V VDE 0801/01.90+A1 10/94（仅Triconv9.x，修正案A1 DIN VDE 0116/10.89熔炉电气设备IEC 61131第2/1998部分，EN 61131第2/0595部分（仅Tricon v9.x）可编程控制器第2部分：设备要求和测试。假设过电压为II类和B区（EMC抗扰度）。IEC 61131，第2/2003部分（仅限Tricon v10.x）可编程控制器第2部分：设备要求和测试。假设过电压类别II和B区（EMC抗扰度）为国际认证19 Tricon v9–v10系统的规划和安装指南。有关特定应用的安装说明，请参阅第3章“安装和维护”。美国核管理委员会（NRC）NRC已证明，Tricon控制器适合在NRC安全评估报告（SER）ML013470433、Triconex公司专题报告审查7286-545、“资格总结报告”和7286-546中引用的限制和指南范围内用于核1E应用，“资格总结报告修正案1”，修订版1。
19 • European Union CE Mark on page 20 Canadian Standards Association (CSA) CSA has certified that the Tricon controller is in full compliance with the following internationally recognized electrical safety standards and is qualified for general use in North American and other jurisdictions requiring compliance with these standards. Factory Mutual FM has certified the Tricon controller is in full compliance with the following international recognized standards and is qualified for use in Class I, Division 2 Temperature T4, Groups A, B, C, and D hazardous indoor (or outdoor in a NEMA 4 cabinet) locations. For hazardous location applications, refer to Chapter 3, Installation and Maintenance for application-specific installation instructions. Standard Number Title CAN/CSA-C22.2 No.0-M91 General Requirements-Canadian Electrical Code, Part II CSA Std C22.2 No.0.4-M1982 Bonding and Grounding of Electrical Equipment (Protective Grounding) CSA Std C22.2 No. 142-M1987 Process Control Equipment UL Std No. 508 Industrial Control Equipment Standard Number Title 3611 Electrical Equipment for use in Class I-Division 2; Class II-Division 2; and Class IIIDivisions 1 and 2, Hazardous Locations 3810 Electrical and Electronic Test, Measuring and Process Control Equipment 3600 3600 Electrical Equipment for Use in Hazardous (Classified) Locations-General Requirements 18 Chapter 1 Introduction Planning and Installation Guide for Tricon v9–v10 Systems TÜV Rheinland/Berlin-Brandenburg TÜV has certified that the Tricon controller is in full compliance with the internationally recognized standards listed below, and thus is qualified for use in the following applications and jurisdictions. • Emergency safety shutdown or other critical control applications requiring SIL 1-3 certification per the functional safety requirements of IEC 61508 (only Tricon v9.6 or later) • Emergency safety shutdown or other critical control applications requiring AK 1-AK6 certification per the functional safety requirements of DIN V 19250 and DIN V VDE 0801 (only Tricon v9.x) • Fire and gas detection applications requiring certification per the requirements of EN 54 • Fire and gas detection applications requiring certification per the requirements of NFPA 72 (only Tricon v9.6 or later) • Burner management applications requiring certification per the requirements of DIN VDE 0116 • Burner management applications requiring certification per the requirements of NFPA 8501 or NFPA 8502 (only Tricon v9.6 or later) • All applications for use in European Union or other jurisdictions requiring compliance with the EMC Directive No. 89/336/EEC and Low Voltage Equipment Directive No. 72/23/EEC • All applications for use in the European Union or other jurisdictions requiring compliance with the ATEX Directive No. 94/9/EC for Zone 2, Group IIB hazardous locations • Environmental, health, and safety applications in semiconductor manufacturing facilities per the requirements of SEMI S2 (only Tricon v9.4) Standard Number Title IEC 61508, Parts 1-7, 2000 (only Tricon v9.6 or later) Functional Safety of Electrical/Electronic/Programmable Electronic Safety-Related Systems DIN V 19250/05:94 (only Tricon v9.x) Fundamental Safety Aspects to Be Considered for Measurement and Control Protective Equipment DIN V VDE 0801/01.90+A1 10/94 (only Tricon v9.x) Principles for Computers in Safety-Related Systems, Amendment A1 DIN VDE 0116/10.89 Electrical Equipment of Furnaces IEC 61131, Part 2/1998, EN 61131, Part2/0595 (only Tricon v9.x) Programmable Controllers Part 2: Equipment Requirements and Test. Overvoltage Category II and Zone B (EMC Immunity) are assumed. IEC 61131, Part 2/2003 (only Tricon v10.x) Programmable Controllers Part 2: Equipment Requirements and Test. Overvoltage Category II and Zone B (EMC Immunity) are assumed International Approvals 19 Planning and Installation Guide for Tricon v9–v10 Systems Refer to Chapter 3, Installation and Maintenance for application-specific installation instructions. U.S. Nuclear Regulatory Commission (NRC) The NRC has certified that the Tricon controller is suitable for use in nuclear 1E applications within the limitations and guidelines referenced in the NRC Safety Evaluation Report (SER) ML013470433, Review of Triconex Corporation Topical Reports 7286-545, “Qualification Summary Report” and 7286-546, “Amendment 1 To Qualification Summary Report,” Revision 1.
