IS200ISBEH2ABB控制卡件,输出卡件
四个串行端口具有唯一地址，可用于Modbus或TriStation通信，速度高达每秒19.2千位。单个Tricon高密度控制器最多支持两个EICM模块，这些模块位于一个逻辑插槽中。这种配置总共提供六个Modbus端口、两个TriStation端口和两个打印机端口。有关规格，请参阅第151页的增强型智能通信模块（EICM）。Hiway接口模块（HIM）Hiway接口接口模块（HEM）通过Hiway网关和本地控制网络（LCN）充当Tricon控制器和霍尼韦尔TDC-3000控制系统之间的接口。HIM还可以通过数据通道与霍尼韦尔TDC-2000控制系统连接。HIM使LCN或数据通道上的高阶设备（如计算机和操作员工作站）能够与Tricon控制器通信。HIM允许冗余BNC直接连接到数据通道，并具有与多达四个扩展数据通道端口（DHP）地址相同的功能容量。有关规格，请参阅第153页的Hiway接口模块（HIM）。16第1章Tricon v9–v10系统网络通信模块（NCM）简介规划和安装指南网络通信模块使Tricon控制器能够使用每秒10兆比特的高速数据链路与其他Triconex控制器和以太网上的外部设备进行通信。NCMG允许Tricon控制器根据GPS信息同步控制器时间。有关规格，请参阅第155页的网络通信模块（NCM）。安全管理器模块（SMM）安全管理器组件（SMM，Safety Manager Module）充当Tricon控制器和霍尼韦尔通用控制网络（UCN）之间的接口，该网络是TDC-3000分布式控制系统的三个主要网络之一。在霍尼韦尔系统看来，SMM是UCN上的一个安全节点，它以全网络数据速率传输过程信息，以便在TDC-3000上的任何地方使用。SMM以霍尼韦尔操作员熟悉的显示格式向操作员工作站传输所有Tricon控制器别名数据（包括系统变量和系统别名）和诊断信息。有关规格，请参阅第157页的安全管理器模块（SMM）。Tricon通信模块（TCM）Tricon通信组件（TCM）使Tricon控制器能够与Modbus设备（主设备或从设备）、TriStation PC、网络打印机、其他Triconex控制器和以太网上的其他外部设备通信。每个TCM有四个串行端口、两个以太网网络端口和一个调试端口（用于Triconex）。TCM型号4353和4354具有嵌入式OPC服务器，允许多达10个OPC客户端订阅OPC服务器收集的数据。嵌入式OPC服务器支持数据访问标准和报警和事件标准。单个Tricon控制器最多支持四个TCM，它们位于两个逻辑插槽中。这种配置总共提供了16个串行端口和8个以太网网络端口。TCM仅与Tricon v10.0及更高版本的系统兼容。TCM型号4351B、4352B、4353和4354仅与Tricon v10.3及更高版本系统兼容。有关完整的兼容性信息，请参阅IPS全球客户支持网站上的Tricon产品发布通知。有关规格，请参阅第159页的Tricon通信模块（TCM）。国际认证17 Tricon v9–v10系统规划和安装指南国际认证Tricon控制器已通过以下国际公认认证机构的认证，符合多项国际公认标准，这些认证使Tricon在全球范围内适用于安全关键应用。各认证机构的测试报告可应要求提供。主题包括：•加拿大标准协会（CSA）第17页•工厂互助会第17页；TüV Rheinland/Berlin-Brandenburg第18页•美国核管理委员会（NRC）第.
The four serial ports are uniquely addressed and can be used for Modbus or TriStation communication at speeds up to 19.2 kilobits per second. A single Tricon High-Density controller supports up to two EICM modules which reside in one logical slot. This arrangement provides a total of six Modbus ports, two TriStation ports, and two printer ports. For specifications, see Enhanced Intelligent Communication Module (EICM) on page 151. Hiway Interface Module (HIM) The Hiway Interface Module (HIM) acts as an interface between a Tricon controller and a Honeywell TDC-3000 control system via the Hiway Gateway and Local Control Network (LCN). The HIM can also interface with a Honeywell TDC-2000 control system via the Data Hiway. The HIM enables higher-order devices on the LCN or Data Hiway, such as computers and operator workstations, to communicate with the Tricon controller. The HIM allows redundant BNC connections directly to the Data Hiway and has the same functional capacity as up to four extended Data Hiway Port (DHP) addresses. For specifications, see Hiway Interface Module (HIM) on page 153. 16 Chapter 1 Introduction Planning and Installation Guide for Tricon v9–v10 Systems Network Communication Module (NCM) The Network Communication Module (NCM) enables the Tricon controller to communicate with other Triconex controllers and with external devices on Ethernet networks using a highspeed 10 megabits per second data link. The NCMG allows the Tricon controller to synchronize controller time based on GPS information. For specifications, see Network Communication Module (NCM) on page 155. Safety Manager Module (SMM) The Safety Manager Module (SMM) acts as an interface between a Tricon controller and a Honeywell Universal Control Network (UCN), which is one of three principal networks of the TDC-3000 Distributed Control System. Appearing to the Honeywell system as a safety node on the UCN, the SMM communicates process information at full network data rates for use anywhere on the TDC-3000. The SMM transmits all Tricon controller aliased data (including system variables and system aliases) and diagnostic information to operator workstations in display formats that are familiar to Honeywell operators. For specifications, see Safety Manager Module (SMM) on page 157. Tricon Communication Module (TCM) The Tricon Communication Module (TCM) enables a Tricon controller to communicate with Modbus devices (masters or slaves), a TriStation PC, a network printer, other Triconex controllers, and other external devices on Ethernet networks. Each TCM has four serial ports, two Ethernet network ports, and one debug port (for Triconex use). TCM models 4353 and 4354 have an embedded OPC server, which allows up to ten OPC clients to subscribe to data collected by the OPC server. The embedded OPC server supports the Data Access standard and the Alarms and Events standard. A single Tricon controller supports up to four TCMs, which reside in two logical slots. This arrangement provides a total of sixteen serial ports and eight Ethernet network ports. TCMs are compatible with only Tricon v10.0 systems and later. TCM models 4351B, 4352B, 4353, and 4354 are compatible with only Tricon v10.3 systems and later. For complete compatibility information, see the Tricon Product Release Notices available on the IPS Global Client Support Web Site. For specifications, see Tricon Communication Module (TCM) on page 159. International Approvals 17 Planning and Installation Guide for Tricon v9–v10 Systems International Approvals The Tricon controller has been certified as complying with multiple internationally recognized standards by the following internationally recognized certification agencies, these certifications have qualified the Tricon for use around the world in safety critical applications. Test reports from the various certification agencies are available upon request. Topics include: • Canadian Standards Association (CSA) on page 17 • Factory Mutual on page 17 • TÜV Rheinland/Berlin-Brandenburg on page 18 • U.S. Nuclear Regulatory Commission (NRC) on page
