IS200ICIAH1AAB系统模块卡件
有关详细信息，请参阅控制器安装手册。安装OEM、系统集成商或最终用户负责正确安装PLC设备，以确保安全可靠运行。产品手册提供了有关PLC设备安装、启动和正确使用的详细信息。PLC编程软件附带的安装手册描述了如何正确安装设备。如果PLC安装必须符合受支持的标准，如FCC或CE指令，请参阅PLC编程软件附带的《符合标准的安装要求》，以获取更多指南。3 96 MHz、32位、浮点、6 Mbyte（中等）内存中央处理单元GFK-1433E PLC CPU 1999年11月系列90-70可编程控制器数据表手册GFK-0600F 21-3未参考适用的可编程控制器安装手册，不得尝试安装。将电池连接到模块上的任一电池连接器（见图2）。将拨动开关置于停机位置。将钥匙开关置于记忆保护断开位置。确保机架电源已关闭。将CPX 928模块安装在机架0的插槽1中（见图1）。打开电源。模块应通电，左上角（正常）LED应闪烁。当诊断成功完成时，左上角LED保持亮起，第二个（RUN）和第三个（EN）LED熄灭。如果钥匙开关处于off位置，第四个（左下角）LED（MEM PROTECT）熄灭。CPU现在已准备好编程（如果并联连接，无论钥匙位置如何，CPU都可以编程）。程序验证后，拨动开关可移动到适当的操作模式位置；启用输出时运行、禁用输出时运行或停止。七个LED指示拨动开关的位置、内存保护状态、串行端口活动状态和程序状态。编程器连接，并行对于并行接口（仅限MS-DOS编程器），编程器与总线变送器模块（IC697BEM713）的顶部端口相连，如图1所示。有关编程功能的说明，请参阅适用的编程软件用户手册。MEM PROTECT a45727打开更换电池连接器6 MBYTE记忆板CPX 928当前安装的电池连接器记忆保护钥匙开关Y R E B A T模块IC697CPX928标签44A726758–153R01串行端口3仅在插槽1中使用此模块顶部远程编程器上的CPX 928OFF OK RUN EN ON=OK，已启用，保护前运行，输出启用运行，输出禁用停止钥匙位置模块功能电池连接器在拔出旧电池之前安装新电池。使用IC697ACC701存储器保护RS-485兼容96 MHz 32位中央处理单元P1 P2 P3串行端口2 RS-485兼容工厂测试For more information, see the controller installation manual. The installation OEM, system integrator or end user is responsible for the correct installation of PLC equipment to ensure safe and reliable operation. The product manual provides detailed information about the installation, startup and proper use of the PLC equipment. The installation manual included with the PLC programming software describes how to properly install the equipment. If the PLC installation must comply with a supported standard, such as FCC or CE directives, refer to the Standard Compliant Installation Requirements included with the PLC programming software for more guidance. 3 96 MHz, 32-bit, floating point, 6 Mbyte (medium) memory central processing unit GFK-1433E PLC CPU November 1999 Series 90-70 Programmable Controller Data Sheet Manual GFK-0600F 21-3 Do not attempt to install without reference to the applicable PLC installation manual. Connect the battery to any battery connector on the module (see Figure 2). Place the toggle switch in the STOP position. Place the keyswitch in the memory protection OFF position. Make sure the rack is powered off. Install the CPX 928 module in slot 1 of rack 0 (see Figure 1). Turn on the power. The module should be powered and the upper left (normal) LED should flash. When the diagnosis is successfully completed, the upper left LED remains on and the second (RUN) and third (EN) LEDs go out. If the key switch is in the off position, the fourth (lower left) LED (MEM PROTECT) goes out. The CPU is now ready for programming (if connected in parallel, the CPU can be programmed regardless of the key position). After program verification, the toggle switch can be moved to the appropriate operating mode position; Run when output is enabled, run when output is disabled, or stop. The seven LEDs indicate the position of the toggle switch, memory protection status, serial port activity status, and program status. The programmer is connected in parallel. For the parallel interface (MS-DOS programmer only), the programmer is connected to the top port of the bus transmitter module (IC697BEM713), as shown in Figure 1. For a description of the programming functions, refer to the applicable programming software user manual. MEM PROTECT a45727 Open and replace the battery connector 6 MBYTE memory board CPX 928 Currently installed battery connector Memory protection key switch Y R E B A T module IC697CPX928 label 44A726758 – 153R01 Serial port 3 Only use CPX 928OFF OK RUN EN ON=OK in slot 1 on the remote programmer at the top of this module, enabled, run before protection, output enable operation, Output disable stop key position module function battery connector Install a new battery before removing the old battery. Use IC697ACC701 memory protection RS-485 compatible 96 MHz 32-bit central processing unit P1 P2 P3 serial port 2 RS-485 compatible factory test
