IS200ISBBG1A工控模块,处理器模块
87 BIOS设置B BIOS设置要启用/禁用传统USB支持和/或为USB控制器分配中断，请执行以下概述的适当操作：1。CPU通电或复位后，立即按F2键进入“PhoenixBIOS设置实用程序”。2.使用箭头键选择“高级”菜单。3.使用箭头键，选择“已安装O/S”设置。按数字键盘上的+或–，在“其他”、“Win95”和“Win98/Win2000”之间切换设置。4.使用箭头键，选择“将中断分配给USB”设置。按数字键盘上的+或–，在“启用”和“禁用”之间切换设置。5.使用箭头键，选择“传统USB支持”设置。按数字键盘上的+或–，在“启用”和“禁用”之间切换设置。6.按F10，然后按ENTER保存设置并退出BIOS。注：有关正确设置，请参见第86页的“在Microsoft Windows操作系统中使用USB键盘/鼠标”。88 B VMIVME-7750产品手册Microsoft Windows 98SE软件驱动程序安装1。在安装Windows 98SE之前，请确保BIOS设置为向USB控制器分配中断。同时确保“Installed O/S”设置为“Win98/Win2000”。有关更改BIOS设置的指南，请参阅第87页的“BIOS设置”。2.按照Windows 98SE手册提供的说明开始安装Windows 98SE。3.在“Windows 98SE安装向导”的“安装选项”部分，确保选择了“典型”，然后单击“下一步”。4.根据需要输入用户名和公司名称，然后单击“下一步”。5.在安装向导的“Windows组件”部分，确保选中“安装最常用的组件”，然后单击“下一步”。6.继续安装，直到Windows 98SE完全安装并最后一次重新启动。请注意，在Windows 98SE安装过程中，计算机将多次重新启动。注意：在整个安装过程中，将Windows 98SE安装CD-ROM保留在CD-ROM驱动器中，因为可能需要复制其他文件。Intel 815芯片集软件安装1。如果尚未安装，请插入Windows驱动程序CD-ROM。2.单击“开始”、“运行”、“浏览”。在“查找范围”下拉选择菜单中，选择“Windows驱动程序”CD-ROM。双击“Win98”文件夹。双击“815chpst”文件夹。双击“Disk1”文件夹。双击“设置”。单击“确定”。3.在“欢迎”窗口中，单击“下一步”。4.单击“是”以同意软件许可协议。5.在“自述信息”窗口中单击“下一步”。6.在“安装完成”窗口中，确保选中“是，我要立即重新启动计算机”，然后单击“完成”。计算机将重新启动。7.Windows 98SE将找到新的硬件并安装必要的软件。在“系统设置更改”窗口中，单击“是”重新启动计算机。重新启动后，Windows 98SE将找到其他硬件，并再次显示“系统设置更改”窗口。单击“是”重新启动计算机。Ultra ATA存储驱动程序安装1。如果尚未安装，请插入Windows驱动程序CD-ROM。89 Microsoft Windows 98SE软件驱动程序安装B 2。单击“开始”、“运行”、“浏览”。在“查找范围”下拉选择菜单中，选择“Windows驱动程序”CD-ROM。双击“Win98”文件夹。双击“UltraATA”文件夹。双击“UltraATA”。单击“确定”。3.在“Intel Ultra ATA存储驱动程序6.1设置”窗口中，单击“下一步”。单击“是”以同意许可协议。单击“下一步”两次。4.确保选中“是，我想立即重新启动计算机”，然后单击“完成”。计算机将重新启动。视频驱动程序安装1。如果尚未安装，请插入Windows驱动程序CD-ROM。2.单击“开始”、“运行”、“浏览”。在“查找范围”下拉选择菜单中，选择“Win_drivers”CD-ROM。双击“win98”文件夹。双击“视频”文件夹。双击“设置”。单击“确定”。3.在“Intel（R）810/810E/815/815E/815EM芯片集图形驱动程序软件设置”窗口中，单击“下一步”。4.单击“是”以同意软件许可协议。5.确保选中“是，我想立即重新启动计算机”，然后单击“完成”。计算机将重新启动。
87 BIOS Setup B BIOS Setup To enable/disable Legacy USB Support and/or assign a interrupt to the USB controllers, perform the appropriate actions as outlined below: 1. Immediately after the CPU has been powered on or reset, press F2 to enter the ‘PhoenixBIOS Setup Utility’. 2. Using the arrow keys, select the ‘Advanced’ menu. 3. Using the arrow keys, select the ‘Installed O/S’ setting. Press + or – on the number keypad to toggle the setting between ‘Other’, ‘Win95’ and ‘Win98/Win2000’. 4. Using the arrow keys, select the ‘Assign Interrupt to USB’ setting. Press + or – on the number keypad to toggle the setting between ‘Enabled’ and ‘Disabled’. 5. Using the arrow keys, select the ‘Legacy USB Support’ setting. Press + or – on the number keypad to toggle the setting between ‘Enabled’ and ‘Disabled’. 6. Press F10, then ENTER to save settings and exit the BIOS. NOTE: See “Using USB Keyboard/Mouse with Microsoft Windows Operating Systems” on page 86 for proper settings. 88 B VMIVME-7750 Product Manual Microsoft Windows 98SE Software Driver Installation 1. Prior to installing Windows 98SE, ensure the BIOS is set to assign an interrupt to the USB controller. Also ensure ‘Installed O/S’ is set to ‘Win98/Win2000’. See “BIOS Setup” on page 87 for guidelines on changing BIOS settings. 2. Begin installation of Windows 98SE, following the instructions provided by the Windows 98SE manual. 3. At the ‘Setup Options’ portion of the ‘Windows 98SE Setup Wizard’, ensure ‘Typical’ is selected and click ‘Next’. 4. Enter the user’s name and the company’s name as appropriate and click ‘Next’. 5. At the ‘Windows Components’ portion of the Setup Wizard, ensure ‘Install the most common components’ is selected and click ‘Next’. 6. Continue with the installation until Windows 98SE is completely installed and has restarted for the last time. Please note that the computer will restart several times during the Windows 98SE installation process. NOTE: Leave the Windows 98SE installation CD-ROM in the CD-ROM drive during the entire setup process as additional files may need to be copied. Intel 815 Chipset Software Installation 1. If not already present, insert the Windows Drivers CD-ROM. 2. Click ‘Start’, ‘Run’, ‘Browse’. In the ‘Look in’ pull-down selection menu, select the ‘Windows Drivers’ CD-ROM. Double-click on the ‘Win98’ folder. Double-click on the ‘815chpst’ folder. Double-click on the ‘Disk1’ folder. Double-click on ‘Setup’. Click ‘OK’. 3. At the ‘Welcome’ window, click ‘Next’. 4. Click ‘Yes’ to agree to the software license agreement. 5. Click ‘Next’ at ‘Readme Information’ window. 6. At the ‘Setup Complete’ window, ensure ‘Yes, I want to restart my computer now’ is selected and click ‘Finish’. The computer will restart. 7. Windows 98SE will find new hardware and install the necessary software. At the ‘System Settings Change’ window, click ‘Yes’ to restart the computer. Upon restarting, Windows 98SE will find additional hardware and present the ‘System Settings Change’ window again. Click ‘Yes’ to restart the computer. Ultra ATA Storage Driver Installation 1. If not already present, insert the Windows Driver CD-ROM. 89 Microsoft Windows 98SE Software Driver Installation B 2. Click ’Start’, ‘Run’, ‘Browse’. In the ‘Look in’ pull-down selection menu, select the ‘Windows Drivers’ CD-ROM. Double-click on the ‘Win98’ folder. Double-click on the ‘UltraATA’ folder. Double-click on ’UltraATA’. Click ‘OK’. 3. At the ‘Intel Ultra ATA Storage Driver 6.1 Setup’ window, click ‘Next’. Click ‘Yes’ to agree to the license agreement. Click ‘Next’ twice. 4. Ensure ‘Yes I want to restart my computer now’ is selected and click ‘Finish’. The computer will restart. Video Driver Installation 1. If not already present, insert the Windows Drivers CD-ROM. 2. Click ‘Start’, ‘Run’, ‘Browse’. In the ‘Look in’ pull-down selection menu, select the ‘Win_drivers’ CD-ROM. Double-click on the ‘win98’ folder. Double-click on the ‘Video’ folder. Double-click on ‘Setup’. Click ‘OK’. 3. At the ‘Intel(R) 810/810E/815/815E/815EM Chipset Graphics Driver Software Setup’ window, click ‘Next’. 4. Click ‘Yes’ to agree to the software license agreement. 5. Ensure ‘Yes, I want to restart my computer now’ is selected and click ‘Finish’. The computer will restart.
