IS200EXHSG4A模块控制器,模块备件
1.当交流电源因电力公司问题或在同一电源系统中遇到大电流负载而暂时低于低电压保护水平时，逆变器将立即停止输出。如果电源在2秒内恢复，逆变器可以使用其速度搜索程序重新启动。2.当F_23=0时：（1）如果瞬时功率损失小于2秒，则逆变器在通电后0.5秒通过速度搜索自动恢复运行。自动重新启动次数不受F_24的限制。（2） 如果瞬时功率损失很长，则逆变器的操作基于F_10的设置和外部开关的条件。（3） 如果瞬时损失时间介于上述两者之间，则逆变器是否自动重启取决于F_24:F_24=0：自动重启禁用。F_24=1~5：自动重启启用1~5次。3.当F_23=1时，（1）瞬时断电后加电，逆变器不会启动。即使在F_24>0。（2） 如果瞬时功率损失很长，则必须手动重新启动逆变器。逆变器的操作基于F_10的设置和外部开关的条件。4.重新启动逆变器时，逆变器的操作基于F_10的设置和外部开关（FWD/REV按钮）的条件。（1） 当F_10=0时，逆变器在重新启动后不会启动。（2） 当F_10=1且外部开关（FWD/REV按钮）关闭时，逆变器在重新启动后不会启动。（3） 当F_10=1且外部开关（FWD/REV按钮）打开时，逆变器将在重启后自动启动。注意：出于安全原因，请在断电后关闭外部开关（FWD/REV按钮），以避免突然断电后可能对机器和人体造成损坏。34 Fn24：自动重新启动次数=0至51。当Fn24=0时，逆变器不会尝试重新启动。（除瞬时功率损失外，详情请参见F_23）2。当Fn24>0时，逆变器将在功能跳闸后约0.5秒通过速度搜索恢复运行。之后，逆变器将加速或减速到当前频率设置。（除瞬时功率损失外，详情请参见F_23）3。当逆变器设置为减速或直流断开时，不执行瞬态重启程序。4.当发生以下任一情况时，将重置瞬时重启计数：（1）10分钟内未发生其他故障（运行或停止中）。（2） 按下RESET（复位）按钮或外部端子RESET（重置）打开。Fn25：出厂设置功能=010：常数初始化至50Hz系统=020：常数初始化为60Hz系统1。当Fn25设置为010时，所有参数恢复为出厂设置。Fn_05=1和Fn_06=50。复位过程完成（50Hz操作）后，Fn_25恢复到000。2.当Fn25设置为020时，所有参数恢复为出厂设置。Fn_05=4和Fn_06=60的设置。复位过程完成（60Hz操作）后，Fn_25恢复到000。Fn26:SP2（1至200Hz），多速2（参考Fn_19，Fn20）Fn27:SP3（1至200 Hz），多速3（参考Fn_19，Fn_20）35 F_28：直接启动=0：远程运行命令开启时直接启动=1：在CPU版本为2.1的驱动器上执行远程运行命令时直接启动禁用（检查功能F_29）当F_28=1且控制模式为远程控制（F_10=1）时，如果电源接通时RUN开关打开，逆变器无法启动，必须关闭RUN开关并再次打开，然后逆变器才能启动。Fn_29：软件（程序）版本Fn_30：故障轨迹1。故障轨迹：通过小数点的位置指示故障发生的顺序。x、 xx表示最近发生的故障。xx.x表示上次发生的故障。xxx。表示记录中最早的故障。2.进入Fn_30功能后，将首先显示x.xx记录。之后，按下按钮可以读出xx.x xxx。x、 xx、、、连续。3.进入Fn_30功能后，如果按下RESET（重置）按钮，将清除所有三个故障记录。指示显示-.--，-.-，和---。4.当故障存储器的内容指示O.CC时，指示最新的故障代码是OC-C，依此类推。36 3.4。故障指示和对策3.4.1。手动复位不工作故障指示内容可能导致计数器程序错误外部噪声干扰将RC电涌吸收器与产生噪声的磁触点EEPROM错误EEPROM故障更换EEPROM电压过高而不工作1。电源电压过高。2.检测电路故障1。检查电源2。返回逆变器进行维修电压过低而不工作1。电源电压过低。2.检测电路有缺陷。1.检查电源2。返回逆变器f
1. When the AC power supply is temporary below low voltage protection levels because of power company issues or encountering large current loading in the same power supply system, the inverter will stop its output immediately. If the power source resumes within 2 seconds, the inverter can restart by using its speed search program. 2. When F_23=0: (1) If the momentary power loss is less than 2 seconds, the inverter resume operation automatically via speed search at 0.5 seconds after power up. The number of auto-restart times is not limited by F_24. (2) If the momentary power loss is long, the operation of the inverter is based on the setup of F_10 and the condition of external switch. (3) If the time of momentary loss is between the above two, whether the inverter will auto-restart depends on F_24: F_24=0: auto-restart disabled. F_24=1~5: auto-restart enabled 1~5 times. 3. When F_23=1, (1) Power up after momentary power loss, the inverter will not start. Even under F_24>0. (2) If the momentary power loss is long, the inverter must be restart manually. The operation of the inverter is based on the setup of F_10 and the condition of external switch. 4. When restart the inverter, the operation of the inverter is based on the setup of F_10 and the condition of external switches (FWD/REV button). (1) When F_10=0, the inverter will not start after restart. (2) When F_10=1 and the external switch (FWD/REV button) is OFF, the inverter will not start after restart. (3) When F_10=1 and the external switch (FWD/REV button) is ON, the inverter will start automatically after restart. Attention: Base on safety reason, please turn off the external switch (FWD/REV button) after power loss to avoid possible damage to the machine and the human body after sudden regeneration of power. 34 Fn_24: Number of Auto-restart times = 0 up to 5 1. When Fn_24 = 0, the inverter will not try to restart. (Except for momentary power loss, please refer to F_23 for details) 2. When Fn_24 > 0 , the inverter will resume operation via SPEED SEARCH at approximately 0.5 second after a function trip. After that, the inverter will accelerate or decelerate to current frequency setting. (Except for momentary power loss, please refer to F_23 for details) 3. When the inverter is set to deceleration or DC breaking, the transient restart procedure is not performed. 4. When either of following situation happen, the transient restart count will be reset: (1) No additional malfunction (in operation or stop) occurs within 10 minutes. (2) Press RESET button or external terminal RESET is ON. Fn_25 : Factory settings function = 010 : Constants initialisation to 50Hz system = 020 : Constants initialisation to 60Hz system 1. When Fn_25 is set to 010, all parameters are restored to factory settings. The settings of Fn_05 =1 and Fn_06 = 50. Fn_25 is restored back to 000 after the reset process complete (50Hz operation). 2. When Fn_25 is set to 020, all parameters are restored to factory settings. The settings of Fn_05 =4 and Fn_06 = 60. Fn_25 is restored back to 000 after the reset process complete (60Hz operation). Fn_26: SP2 (1 up to 200Hz), multi-speed 2 (Refer to Fn_19, Fn_20) Fn_27: SP3 (1 up to 200Hz), multi-speed 3 (Refer to Fn_19, Fn_20) 35 F_28: Direct start = 0 : Direct start enable when remote Run command on = 1 : Direct start disable when remote Run command on drives with CPU version from 2.1 (check function F_29) When F_28 = 1 and control mode is remote control (F_10 = 1), the inverter can not start if RUN switch is ON when power is engaged, must be turned the RUN switch OFF and turned ON again, then inverter can start. Fn_29: software (program) version Fn_30: Fault trace 1. Fault trace : indicate the sequence of the occurrence of malfunctions by the location of decimal point. x.xx indicate a recently happened malfunction. xx.x indicate the last malfunction that happened. xxx. indicated the earliest malfunction in the record. 2. After entering the Fn_30 function, the x.xx record will be displayed first. After that, press button can read out xx.x xxx. x.xx ,,, consecutively. 3. After entering Fn_30 function, if the RESET button is pressed, all three malfunction record will be cleared. Indication display -.--, --.-, and ---. 4. When the content of malfunction memory indicate O.CC, indicate the latest malfunction code is OC-C and so on. 36 3.4. Malfunction indication and countermeasure 3.4.1. Manual reset inoperative faults INDICATION CONTENT POSSIBLE CAUSE COUNTERMEASURE Program error Outside noise interference Place a RC surge absorber in parallel with the noise generating magnetic contact EEPROM error EEPROM defective Replace EEPROM Voltage too high while not operating 1. Power source voltage too high. 2. Detection circuitry defective 1. Examining the power supply 2. Return the inverter for repair Voltage too low while not operating 1. Power source voltage too low. 2. Detection circuitry defective. 1. Examining the power supply 2. Return the inverter for repair Inverter over heat while not operating 1. Detection circuit defective. 2. Environment over-heat or poor ventilation 1. Return the inverter for repair 2. Improve ventilation 3.4.2. Manual reset operative faults (Auto-Reset inoperative) INDICATION CONTENT POSSIBLE CAUSE COUNTERMEASURE Over-current at stop
