IS200F0SAG1AAA模拟量电子模块
Hz分辨率数字：0.1Hz（0~99.9Hz）/1Hz（100~120Hz）模拟：0.06Hz/60Hz键盘设置直接设置▲▼ 按钮。外部信号设置0~110V、4~20mA、0~20mA频率控制其他功能频率上限和下限载波频率4-8kHz 4-16kHz加速/减速时间0.1~999秒V/F模式6模式扭矩控制扭矩提升水平可调（手动扭矩提升）多功能输入2点，用作多速1（Sp1）/点动/外部紧急停止/外部复位2点，用作多速1（Sp1）/多速2（Sp2）/点动/外部紧急停止/外部复位多功能输出1a继电器端子，设置为故障/运行/频率。制动扭矩约为20%。不允许使用外部制动电阻器。100%带外部电阻器通用控制其他功能减速或自由运行停止、自动复位、直流制动频率/电压/时间可通过常数设置。显示3个数字LED显示频率/逆变器参数/故障记录/程序版本指示功能7段*3显示频率/变频器参数/故障录波/程序版本。工作温度-10至+40°C（无屏蔽标签：-10至+50°C）湿度0至95%RH，无冷凝。1 G（9.8 m/s2）下的振动EMC规范EN 5008-1、EN 5008-2、EN 50082-1、EN 50082-2、EN 50178防护等级IP20 UL UL508C过载保护150%，持续1分钟。过电压直流电压＞410V（200V系列），直流电压＞800V（400V系列）欠电压直流电压＜200V（200V系列），DC<400V（400V系列）瞬时功率损失0~2秒：VAT20可通过速度搜索重新启动保护功能失速防止加速/减速/恒速输出端子短路电子电路保护接地故障电子电路保护功能其他功能散热片保护，电流限制尺寸（宽x高x深）mm 72x132x118 118x143x172安装通过安装螺钉或DIN导轨安装（可选）。12 2.4. 接线塑壳断路器/接触器l GE Power Controls维护和维修不适用于以下情况造成的损坏：（1）由于缺少合适的塑壳断路器或电源和逆变器之间安装了容量过大的断路器而导致的逆变器损坏。（2） 逆变器和电机之间的串联磁性接触器、相位超前电容器或浪涌保护器对逆变器造成损坏。型号：U20N 0K2、0K4、0K7 1K5、2K2型号：U20X 0K7、1K5、，2K2塑壳断路器，由GE 20A 30A 30A磁性接触器（MC）制造，由GE CL00制造，由通用电气CL00制造一次电路端子（TM1）导线尺寸2.5 mm2端子螺钉M3导线尺寸4 mm2端子螺钉M4导线尺寸2.5 mm端子螺钉M3信号端子（TM2）1~11导线尺寸0.75 mm2（#18 AWG），端子螺钉M3 l请使用容量适当的三相鼠笼式感应电动机。l如果使用逆变器驱动多个电机，总容量必须小于逆变器的容量。每个电机前面必须安装额外的热继电器。在50Hz时，使用电机铭牌上规定额定值的1.0倍Fn_18，在60Hz时，使用电动机铭牌上规定的额定值的1.1倍。l不要在逆变器和电机之间安装相位超前电容器、LC或RC元件。T1 T2 T3 L1 L2 13外围设备的应用和预防措施电源l确保以正确的额定电压应用电源，以防止损坏逆变器。l断路器必须安装在交流电源和逆变器之间。塑壳断路器（MCCB）l使用适用于逆变器额定电压和电流额定值的适当断路器来打开/关闭逆变器电源，并作为逆变器的保护。l不要操作断路器打开或关闭逆变器。漏电断路器（剩余电流装置）l应增加漏电断路器，以防止漏电导致误操作，并确保人员安全。磁性触点l在正常操作时可以省略磁性触点。为了利用外部控制、自动重启或断路控制器，必须在一次侧增加磁触点。l不要操作磁性触点来打开或关闭逆变器。功率改进交流电抗器l如果使用大容量电源（超过600kVA），可增加额外的交流电抗器以提高功率因数。逆变器l电源输入端子L1和L2在相序上没有区别，它们可以任意连接。可以交换它们的连接。l输出端子T1、T2和T3应分别连接到电机的U、V和W端子。如果电机以与逆变器相反的方向转动，只需更换三线连接中的两线即可纠正故障
Hz Resolution Digital : 0.1Hz (0~99.9Hz) / 1Hz (100~120Hz) Analog: 0.06Hz/60Hz Keyboard setting Directly setup by ▲▼ buttons. External signal setting 0~10V, 4~20mA , 0~20mA Freq. control Other function Frequency upper and lower limit Carrier frequency 4-8kHz 4-16kHz Accelerate/decelerate time 0.1~ 999 Sec V/F pattern 6 patterns Torque control Torque boost level adjustable (manual torque boost) Multi-function input 2 point, to be used as multi-speed 1(Sp1) / Jog / External emergency stop / External reset 2 point, to be used as multi-speed 1(Sp1) / multi-speed 2 (Sp2) / Jog / External emergency stop / External reset Multi-function output 1a Relay terminal, to be setup as Fault / Running / Frequency. Braking torque About 20%. Not allowable external braking resistor. 100% with external resistor General control Other function Decelerate or free run stop, Auto reset, DC braking frequency / Voltage / Time can be setup by constants. Display 3 digital LED display frequency / inverter parameter / fault record / program version Indication function 7 segments*3 indicate frequency / inverter parameter / fault record / program version. Operating temperature -10 to +40°C (without shield sticker: -10 to +50°C) Humidity 0~95% RH non-condensing. Vibration Under 1 G ( 9.8 m/s2 ) EMC specification EN 5008-1, EN 5008-2, EN 50082-1, EN 50082-2, EN 50178 Protection level IP20 UL UL508C Overload protection 150% for 1min. Over-voltage DC voltage > 410V (200V series), DC > 800V (400V series) Under voltage DC voltage < 200V (200V series), DC < 400V (400V series) Momentary power-loss 0 ~ 2 sec : VAT20 can be restart by speed search Protection function Stall prevention Accelerate / Decelerate / Constant speed Output terminal short-circuit Electronic circuitry protection Protection Grounding fault Electronic circuitry protection function Other function Heat sink protection , Current limit Dimensions (WxHxD) mm 72x132x118 118x143x172 Installation Install by mounting screw or DIN rail (Option). 12 2.4. Wiring Moulded-Case Circuit Breaker / Contactor l GE Power Controls maintenance and service do not apply to damage caused by following situation: (1) Damage to the inverter caused by the lack of appropriate molded-case circuit breaker or a circuit breaker with too large capacity is installed in between the power supply and the inverter. (2) Damage to the inverter caused by the serial magnetic contactor, phase advancing capacitor, or surge-protector in between the inverter and the motor. Type No: U20N 0K2, 0K4, 0K7 1K5, 2K2 Type No: U20X 0K7, 1K5, 2K2 Moulded-case circuit breaker Made by GE 20A 30A 30A Magnetic Contactor (MC) Made by GE CL00 Made by GE CL00 Made by GE CL00 Primary Circuit Terminal (TM1) Wire dimension 2.5 mm2 Terminal screw M3 Wire dimension 4 mm2 Terminal screw M3 Wire dimension 2.5 mm2 Terminal screw M3 Signal Terminal (TM2) 1~11 Wire dimension 0.75mm2 (#18 AWG), Terminal screw M3 l Please utilize three-phase squirrel-cage induction motor with appropriate capacity. l If a inverter is used to drive more than one motor, the total capacity must be smaller than the capacity of the inverter. Additional thermal relay must be installed in front of every motor. Use the Fn_18 at 1.0 times of the rated value specified on the motor nameplate at 50Hz, 1.1 times of the rated value specified on the motor nameplate at 60Hz. l Do not install phase advancing capacitor, LC, or RC component between the inverter and the motor. T1 T2 T3 L1 L2 13 Application and precautions of peripherals Power Source l Ensure to apply power source at correct rated voltage to prevent form damaging the inverter. l Circuit breaker must be installed in between the AC power supply and the inverter. Moulded-case circuit breaker (MCCB) l Utilize appropriate circuit breaker suitable for the rated voltage and current ratings of the inverter to switch ON/OFF the power supply to the inverter and as a protection for the inverter. l Do not operate the circuit breaker to switch ON or OFF the inverter. Earth leakage circuit breaker (Residual current device) l Leakage circuit breaker should be added to prevent false operation cause by leakage current and to ensure personnel safety. Magnetic Contact l The Magnetic Contact can be omitted at ordinary operation. To utilize external control, automatic restart, or breaking controller the magnetic contact must be added at the primary side. l Do not operate the magnetic contact to switch ON or OFF the inverter. Power improvement AC Reactor l If large capacity power source is applied (over 600kVA), additional AC reactor may be added to improve power factor. Inverter l Power supply input terminals L1 and L2 is not differentiated on phase sequence, they can be arbitrarily connected. Their connection may be exchanged. l Output terminal T1, T2, and T3 should be connected to the U, V, and W terminals of the motor respectively. If motor turns in opposite direction of the inverter, simply exchanging two of three wire connection may correct this problem. l Output terminal T1, T2, and T3 must not be connected to power source to prevent from damaging inverter. l Grounding terminal. Properly ground the grounding terminal in compliance to local codes Power supply Moulded-case circuit breaker or ground fault interruptor Electricalmagnetic contactor AC reactor for power factor improvement VAT20 Inverter Motor 14 (A) External wiring should be carried out in accordance with following requirement. Check and reassure the wiring is correct after the wiring is complete. (Do not utilize the control circuitry buzzer to check the wiring.) EMI connecting: It is very important that the connections between the frequency inverter with the screened motor cable and the EMI filter during the EMI tests are as following. l Use a metal grounding plate and place the frequency inverter and the EMI filter on the plate. l Use a screened motor cable with 4 connectors ( U,V,W,& Earth ), don’t use the shielding as safety earth ( shield is high frequency earth ) l Remove painting around the two metal
