IS200FOSAG1A工控自动化卡件
以避免电源突然再生后可能对机器和人体造成损坏。在操作警告下，不要在操作过程中打开或关闭电机。否则，可能导致逆变器过流故障。警告l在电源接通时，请勿拆下变频器的前盖，以免触电造成人员伤害。l启用自动重启功能后，电机和机械将在完全停止运行后自动重启。请勿靠近机器，以免人员受伤。6注意事项l请勿触摸散热器底座。l逆变器可以从低速到高速范围轻松操作。请重新确认电机和机械的工作范围。l在逆变器运行时，不要检查逆变器PCB上的信号。l所有逆变器在交付前均已正确调整。不要试图调整。注意：在确保电源关闭且电源LED熄灭之前，不要继续进行拆卸或检查程序。检查和维护期间注意：逆变器环境温度应在-10℃~+40℃，湿度低于95%RH，无冷凝。小心拆除屏蔽标签后，环境温度应在-10℃和+50℃之间，湿度应在95%RH以下，无冷凝。此外，逆变器应无滴水或金属灰尘。7 1.2. 操作环境注意事项避免阳光直射远离腐蚀性气体或液体远离油脂和气体远离含盐环境远离雨水或滴水可能进入逆变器的地方避免金属粉尘和多尘环境避免剧烈振动避免高温避免环境温度过高远离高电磁波或超高频波。远离放射性物质远离易燃材料油正确对齐正确对齐错误对齐错误对齐正确对齐冷却风扇冷却风扇冷却扇第2章。硬件说明和安装2.1。操作环境逆变器的安装位置直接影响逆变器的全部功能和寿命。请仔细选择安装地点，以满足以下要求：l垂直安装装置l环境温度：-10℃至+50℃l避免靠近任何加热设备l避免滴水或潮湿环境l避免阳光直射l避免油或含盐腐蚀性气体l避免接触腐蚀性液体或气体l防止外来灰尘、灰尘、，l远离放射性物质或易燃材料l避免电磁干扰（焊接或动力机械）l避免振动，如果无法避免振动，应安装防振器以减少振动。l如果逆变器安装在控制面板中，请撕下VAT20的屏蔽标签。应安装额外的冷却风扇，以将环境降低到50OC以下。逆变器的安装必须使逆变器的正面朝前，逆变器的顶部朝上，以便更好地散热。l安装房间必须符合以下要求。12 cm（min）12 cm（min.）12 cm。类型编号定义逆变器类型→ U20N0K7S（例如）输入额定功率→ I/P:AC 1ph 200~240V 50/60Hz输出额定值→ O/P:AC 3ph 0~240V 1.6kVA 4.2A U20-N 0K7-S系列电源电压
after power loss to avoid possible damage to the machine and the human body after sudden regeneration of power. Under Operation WARNING Do not switch ON or OFF motor at the middle of operation. Otherwise, the inverter over-current break-down may be resulted. WARNING l Do not remove the front cover of the inverter when the power is ON to avoid personnel injury caused by electrical shock. l When the automatic restart function is enabled, the motor and machinery will be restarted automatically after fully stop from operation. Do not get close to the machinery to avoid personnel injury. 6 CAUTION l Do not touch the heat-sink base. l The inverter can be easily operated from low-speed to high-speed range. Please reconfirm the operating range of motor and machinery. l Do not examining the signals on the PCB of the inverter when it is under operation. l All inverter had been properly adjusted before delivery. Do not attempt to adjust it. CAUTION Do not proceed with disassemble or examination procedure before ensuring that the power is off and the Power LED extinguished. During examination and maintenance CAUTION Inverter environment should be within temp: –10 OC ~ +40 OC, humidity under 95% RH without condensing. CAUTION After the removal of shield sticker, the environment temperature should be within -10OC and +50OC and humidity under 95% RH without condensing. Besides, the inverter should be free from water dripping or metal dust. 7 1.2. Precautions of operation environment Avoid direct sunlight Keep away from corrosive gas or liquid Keep away from oil grease and gas Keep away from salty environment Keep away where rain or dripping water may get into the inverter Avoid metal dust and dusty environment Avoid massive vibration Avoid heat Avoid where environment temperature is too high Keep away from high electrical-magnetic wave or ultra-high wave. Keep away from radio-active matter Keep away from flammable material oil 8 Correct alignment Correct alignment Correct alignment Wrong alignment Wrong alignment Correct alignment Cooling fan Cooling fan Cooling fan Cooling fan Chapter 2. Hardware Instruction and Installation 2.1. Operation Environment The installation site of the inverter pose direct impact to the fully functionality and the life-span of your inverter. Please carefully choose the installation site to meet following requirements: l Mount the unit vertically l Environment temperature: -10OC to +50OC l Avoid placing close to any heating equipment l Avoid water dripping or humid environment l Avoid direct sunlight l Avoid oil or salty corrosive gas l Avoid contacting corrosive liquid or gas l Prevent foreign dusts, flocks, or metal scraps from entering interior l Away from radioactive matter or flammable material l Avoid electric-magnetic interference (soldering or power machinery) l Avoid vibration, if vibration can not be avoided, anti-rattler should be installed to reduce it. l If inverter is installed in control panel, please tear off shield sticker of VAT20. Additional cooling fan should be installed to lower the environment below 50OC l Installation of the inverter must place the front side of inverter facing front and the top of inverter towards up direction for better heat dissipation. l Installation rooming must be compliant to following requirement. 12 cm (min) 12 cm (min) 12 cm (min) 12 cm (min) 5 cm (min) VAT 20 < 50°C(1) (2) (2) Ventilation Front view Installation direction Side view (1) Maximum temperature in the enclosure 50°C (2) Keep 7 cm for following drives: N1K5, N2K2, X0K7, X1K5, X2K2 9 2.2. Type number definitions Inverter Type → U20N0K7S (for example) Input Power Rating → I/P: AC 1ph 200 ~ 240V 50/60Hz Output Rating → O/P: AC 3ph 0 ~ 240V 1.6kVA 4.2A U20 - N 0K7 - S Series Power Voltage Power
