IS200ICBDH1ACB工控模块卡件
温度范围0至60°C环境兼容性PME编程软件CPU 001 CPU 002 CPU 005 CPU E05 DBI 001 EBI 001 GBI 001 PBI 001 HW，固件版本。固件发布所有BC 1.2 AA 1.5 AA 2.1 AA 2.1 AA 1.1 AA 1.0 AB 1.1 AB 1.1输入特性RTD类型25、100和1000欧姆铂10、50和100欧姆铜100和120欧姆镍604Ω 镍/铁电阻范围0至500Ω 0至3000Ω 精度，25°C时电压测量：温度测量：电阻测量±0.15%电阻（温度）测量±0.15%RTD（温度）温度灵敏度（0°至60°C）读数±0.004%，+/-1.5µV/°C参考输入最大引线电阻50Ω 每个导线。版本之前的模块–DC，固件版本1.1，限制为5Ω 每个导线。GFK-1504N第14章温度传感模块14-5 14 IC200ALG620模拟输入，16位RTD，4通道现场接线端子连接端子连接A1源1 B1无连接A2输入（+）1 B2屏蔽终端点A3输入（-）1 B3无连接A4返回1 B4屏蔽终端点A5源2 B5无连接A6输入（+”）2 B6屏蔽终端点A7输入（-”）2 B7无连接A8返回2 B8屏蔽终端点A9源3 B9无连接A10输入（+终端点A11 In（-）3 B11无连接A12返回3 B12屏蔽终端点A13源4 B13无连接A14 In（+）4 B14屏蔽终端点Al5 In（-）4 B15无连接A16返回4 B16无连接A17无连接B17无连接A18无连接B18无连接带有两排端子IC200CHS002，005 IC200CHS012 AI1源1 AI2源2 AI3源3 AI4源4 14-6 VersaMax模块、电源和载波用户手册GFK-1504N 14 IC200ALG620模拟输入、16位RTD、4通道接线示例下图显示了3线和4线RTD的连接。此模块不需要回路电源。RTD的励磁电流由模块提供，该模块自动将励磁电流与每个配置的RTD类型相匹配。如果未安装RTD，则需要校准3线RTD In（+）In（-）源4线RTD Return In（+（-）Source Return In。如果不可能，电缆屏蔽必须在模块处接地。
temperature range 0 to 60 °C ambient Compatibility PME programming software CPU 001 CPU 002 CPU 005 CPU E05 DBI 001 EBI 001 GBI 001 PBI 001 HW, FW vers. FW release All BC 1.2 AA 1.5 AA 2.1 AA 2.1 AA 1.1 AA 1.0 AB 1.1 AB 1.1 Input Characteristics RTD types 25, 100, and 1000 ohm platinum 10, 50, and 100 ohm copper 100 and 120 ohm nickel 604 Ω nickel/iron Resistance ranges 0 to 500 Ω 0 to 3000 Ω Accuracy, at 25° C on voltage measurement: on temperature measurement: ±0.15% on resistance measurement ±0.15% on RTD (temperature) measurement Temperature sensitivity (0° to 60°C) ±0.004% of reading, +/–1.5µV per °C referred to input Maximum lead resistance 50 Ω per lead. Modules prior to version –DC, firmware revision 1.1, are limited to 5 Ω per lead. GFK-1504N Chapter 14 Temperature Sensing Modules 14-5 14 IC200ALG620 Analog Input, 16 Bit RTD, 4 Channels Field Wiring Terminal Connection Terminal Connection A1 Source 1 B1 No connection A2 In (+) 1 B2 Shield Termination Point A3 In (-) 1 B3 No connection A4 Return 1 B4 Shield Termination Point A5 Source 2 B5 No connection A6 In (+) 2 B6 Shield Termination Point A7 In (-) 2 B7 No connection A8 Return 2 B8 Shield Termination Point A9 Source 3 B9 No connection A10 In (+) 3 B10 Shield Termination Point A11 In (-) 3 B11 No connection A12 Return 3 B12 Shield Termination Point A13 Source 4 B13 No connection A14 In (+) 4 B14 Shield Termination Point A15 In (-) 4 B15 No connection A16 Return 4 B16 No connection A17 No connection B17 No connection A18 No connection B18 No connection Wiring Connections for Carriers with Two Rows of Terminals IC200CHS002, 005 IC200CHS012 AI1 Source 1 AI2 Source 2 AI3 Source 3 AI4 Source 4 14-6 VersaMax Modules, Power Supplies and Carriers User's Manual GFK-1504N 14 IC200ALG620 Analog Input, 16 Bit RTD, 4 Channels Wiring Examples The following illustration shows connections for 3-wire and 4-wire RTDs. No loop power is required for this module. The excitation current for the RTDs is provided by the module, which automatically matches the excitation current to each configured RTD type. Required for Calibration if no RTD is Installed 3-Wire RTD In (+) In (-) Source 4-Wire RTD Return In (+) In (-) Source Return In (+) In (-) Source Return Cable Shield Connections If possible, the cable should be grounded at the source device. If that is not possible, the cable shield must be grounded at the module.
