IS200TBAIH1A模拟量输入模块
用于带状电缆的三个34针IDC连接器尺寸：端子板219mm长X 95mm宽X 30mm深尺寸：接口模块145mm长X 109mm宽X 101mm深（包括配套连接器，包括安装支架）外部输入6点隔离4-20mA电流输入，用于汇点或源操作输入阻抗230欧姆+5%输入保护热敏电阻，限值小于100mA典型信号精度+0.2%超温Silvertech零件号GBC1-CK-0I6 IMC3-CK-AI6 CBL1 CK RRnn CBL1 CK EEnn CBL1 CKEBnn用于6电路块的端子板用于6电路输入块组34路带状电缆的接口模块，终端板至接口模块现场设备连接电缆，带有2个ELCO 8016连接器现场设备连接线缆，另一端带有1个ELCO 801 6连接器和剥线镀锡连接器。4-30 Genius®模块冗余灵活三模块冗余（TMR）系统GFT-177A技术产品概述–1998年2月4个离散输出端接板和接口模块离散输出端板可用于16点和32点汇点和源点Genius块。互补的离散输出接口模块具有用于接线的极化锁定两部分连接器。16点和32点离散接口模块都对输出信号进行分组，并为每个点合并一个二极管，以防止反向负载泄漏电流。强烈建议在现场负载上安装外部反冲抑制二极管。16点离散输出使用单端接板类型，可与汇点或源块一起工作。根据TÜV的建议，32点电源块接线板包含一个自指示保险丝，从安装位置即可看到。输出自动测试期间，保险丝熔断。终端板和接口模块可以容易地配置为4块或2块输出布置。16点离散输出端子板和接口模块的规范工作电压20V至36V DC温度范围0℃至+60℃湿度5%至95%非冷凝连接器：接口模块一个ELCO公8016系列，38针外露触点。用于带状电缆的四个34针IDC连接器尺寸：终端板219mm长X 95mm宽X 30mm深尺寸：接口模块145mm长X 109mm宽X 101mm深输出16个负载，每个通道最大2安培，在35°C负载电压下，1A电源电压下的总电流为15安培–2 V典型最小负载100mA，启用了无负载报告功能Silvertech零件号GBC1-CK-DO16 IMC4-CK-D016 CBL1 CK RRnn CBL1 CK EEnn CBL1 CKEBnn端子板，用于16电路输出块组的源或汇块接口模块。34路带状电缆，终端板至接口模块现场设备连接电缆，带2个ELCO 8016连接器现场设备连接线缆，带1个ELCO 801 6连接器，另一端带剥线和镀锡连接器。32点离散输出端子板和接口模块的规范工作电压10V至30V DC温度范围0℃至+60℃湿度5%至95%非冷凝连接器：接口模块两个ELCO公8016系列，38针外露触点。用于带状电缆的四个34针IDC连接器。尺寸：接线板219mm长X 110mm宽X 30mm深尺寸：接口模块145mm长X 109mm宽X 101mm深输出32个负载，每个通道最大电流为.5安培，负载电压为.5A电源电压–1V典型熔断器0.5A指示保险丝，Bussman型GMT Silvertech零件号GBC1-SC-DO32 GBC1-SK-DO32 IMC4-CK-DO32 CBL1 CK RRnn CBL1 CK EEnn CBL1 CKEBnn 32电路源块端子板32电路汇块接口模块32电路输出块组。34路带状电缆，终端板至接口模块现场设备连接电缆，带2个ELCO 8016连接器现场设备连接线缆，带1个ELCO 801 6连接器，另一端带剥线和镀锡连接器。GFT-177A第4节产品规范4-31 4现场控制总线接口单元和模块现场控制模块安装在单独的终端组件上，通过Genius总线接口单元与Genius总线连接。
Three 34-pin IDC connectors for ribbon cable Size: Termination Boards 219mm length X 95mm width X 30mm depth Size: Interface Modules 145mm length X 109 mm width X 101mm depth (including mating connector, including mounting bracket) External Inputs 6 point isolated 4-20mA current input for sink or source operation Input Impedance 230 Ohms + 5% Input Protection Thermistor limited to less than 100mA typical Signal Accuracy +0.2% over temperature Silvertech part numbers GBC1-CK-0I6 IMC3-CK-AI6 CBL1-CK-RRnn CBL1-CK-EEnn CBL1-CK-EBnn Termination Board for 6-circuit blocks Interface module for 6-circuit input block group 34-way ribbon cable, termination board to interface module Field device connection cable with 2 ELCO 8016 connectors Field device connection cable with 1 ELCO 8016 connector and stripped and tinned connectors at the other end. 4-30 Genius® Modular Redundancy Flexible Triple Modular Redundant (TMR) System GFT-177A Technical Product Overview – February 1998 4 Discrete Output Termination Boards and Interface Modules Discrete output termination boards are available for 16- point and 32-point sink and source Genius blocks. Complementary discrete output interface modules are available with polarized locking two-part connectors for wiring. Both the 16- and 32-point discrete interface modules group the output signals and incorporate a diode for each point to prevent reverse load leakage current. It is highly recommended that an external kickback suppression diode be fitted to the field loads. The 16-point discrete output uses a single termination board type which operates with either sink or source blocks. The 32-point source block termination board incorporates a self–indicating fuse, in accordance with TÜV recommendations, which is visible from the installed position. A blown fuse will be revealed during the output autotest. The termination boards and interface module can easily be configured for either a 4-block or 2-block output arrangement. Specifications for 16-Point Discrete Output Termination Boards and Interface Modules Operating voltage 20V to 36V DC Temperature range 0 degrees C to +60 degrees C Humidity 5% to 95% non-condensing Connectors: Interface Module One ELCO male 8016 series, 38-pin exposed contacts. Four 34-pin IDC connectors for ribbon cable Size: Termination Boards 219mm length X 95mm width X 30mm depth Size: Interface Modules 145mm length X 109 mm width X 101mm depth Outputs 16 loads at 2 Amps per channel max, 15 Amps total at 35°C Load Voltage at 1A Supply Voltage –2V typical Minimum Load 100mA with No Load Reporting enabled Silvertech part numbers GBC1-CK-DO16 IMC4-CK-DO16 CBL1-CK-RRnn CBL1-CK-EEnn CBL1-CK-EBnn Termination Board for Source or Sink block Interface Module for 16-circuit output block group. 34-way ribbon cable, termination board to interface module Field device connection cable with 2 ELCO 8016 connectors Field device connection cable with 1 ELCO 8016 connector and stripped and tinned connectors at the other end. Specifications for 32-Point Discrete Output Termination Boards and Interface Modules Operating voltage 10V to 30V DC Temperature range 0 degrees C to +60 degrees C Humidity 5% to 95% non-condensing Connectors: Interface Module Two ELCO male 8016 series, 38-pin exposed contacts. Four 34-pin IDC connectors for ribbon cable. Size: Termination Boards 219mm length X 110mm width X 30mm depth Size: Interface Modules 145mm length X 109 mm width X 101mm depth Outputs 32 loads at .5 Amps per channel max Load Voltage at .5A Supply Voltage –1V typical Fusing 0.5A indicating fuses, Bussman type GMT Silvertech part numbers GBC1-SC-DO32 GBC1-SK-DO32 IMC4-CK-DO32 CBL1-CK-RRnn CBL1-CK-EEnn CBL1-CK-EBnn Termination Board for 32-circuit Source block Termination Board for 32-circuit Sink block Interface Module for 32-circuit output block group. 34-way ribbon cable, termination board to interface module Field device connection cable with 2 ELCO 8016 connectors Field device connection cable with 1 ELCO 8016 connector and stripped and tinned connectors at the other end. GFT-177A Section 4 Product Specifications 4-31 4 Field Control Bus Interface Units and Modules Field Control modules, which are mounted on separate terminal assemblies, are interfaced to a Genius bus by a Genius Bus Interface Unit.
