IS200TBCIH1BBC工业卡件,ABB卡件
块或电路故障会导致相应的块诊断LED指示和故障记录到每个PLC的故障表中。TMR输入继续与输入组的剩余块或“腿”一起工作。故障的TMR输入块可以热更换（通电），而不会干扰输入组的功能部分或系统的任何其他部分。型号#（IC660）BBD020*BBD021*BBD024*BBD025*数量（带自动测试）15 15 31 31数量（无自动测试）16 16 32 32标称电压24/48Vdc 24/48Vdc 12/24Vdc 5/12/24V DC源或汇点操作源汇点源汇点DC电压范围18–56 18–56 10–30 10–30&4.9–5.3所需DC功率（最大。)300ma 300ma 300mb 300ma块隔离1500V 1500V 850V 850V点状态LED每点1个/点1个每个点诊断LED–单元正常（块或点故障指示）–启用（在线和强制点指示）监控输入诊断是是n/a n/a P.S.断开时间10 ms 10 ms 4ms@12V 20ms@24V 4ms@12伏20ms@24伏工作模式TMR/HSB SIMPLEX TMR/HSASIMPLEX TMR/HSB SIMPLEX TMR/HSB SIMULX输入自动测试（卡在开/关位置）是是是是输入自动测试，（通道到通道短路 产品规范4-21 4离散输入模块规范续以下模块可用作GMR系统中的单工输入模块。单工输入块还根据块类型提供各种诊断功能。有关更多详细信息，请参阅Genius用户手册。型号#（IC660）BBD101*BBD102*BBD103*BBD110 8组数量8组8隔离（4组）8隔离（3组）16组标称电压115Vac 115Vac 125Vdc 115Vac 125 Vdc 115Vac115Vac工作模式SPLX/HSB SPLX/HSB-SPLX/HSB/HSB SIMPLEX交流电压范围（47–63Hz）93–132 93–13 93–132直流电压范围n/a 105–132 105–132 n/a P.S.压降时间1个循环10毫秒直流1个循环10ms直流1循环块隔离1500V 1500V 1500V 1500V点状态LED每点1个/点1个每个点1个诊断LED单元正常（块或点故障指示）-启用（在线和强制点指示）打开输入诊断是是是是短路输入诊断否否是电源损失块诊断损失是是块可选择滤波器时间10–100ms10–100 ms 10–100毫秒10–100 s输入阻抗（典型）13 K ohms 13 K ohm 13 K ohms11.6 K ohms AC开阈值（正常模式）95 VRMS 95 VRMS可编程AC关阈值
A block or circuit fault will cause the corresponding block diagnostic LED indication and fault to be recorded in the fault table of each PLC. The TMR input continues to work with the remaining blocks or "legs" of the input group. A failed TMR input block can be hot swapped (energized) without disturbing the functional part of the input group or any other part of the system. Model # (IC660) BBD020 * BBD021 * BBD024 * BBD025 * Quantity (with automatic test) 15 15 31 31 Quantity (without automatic test) 16 16 32 32 Nominal voltage 24/48Vdc 24/48Vdc 12/24Vdc 5/12/24V DC source or sink point operating source Sink point DC voltage range 18 – 56 18 – 56 10 – 30&4.9 – 5.3 Required DC power (maximum) 300ma, 300ma, 300mb, 300ma, block isolation, 1500V, 1500V, 850V, 850V, point status LED, one for each point, diagnosis LED for each point - the unit is normal (block or point fault indication) - enable (online and forced point indication), monitoring input diagnosis is yes, n/a, n/a, P.S., disconnection time, 10 ms, 10 ms 4ms@12V 20ms@24V 4ms@12 Volts 20ms@24 Volt operating mode TMR/HSB SIMPLEX TMR/HSASIMPLEX TMR/HSB SIMPLEX TMR/HSB SIMULX input automatic test (card is in the ON/OFF position) Yes Yes Yes Yes Input automatic test, (Channel to channel short circuit product specification 4-21 4 Discrete input module specification The following modules can be used as simplex input modules in the GMR system. Simplex input blocks also provide various diagnostic functions according to the block type. For more details, please refer to Genius User's Manual. Model # (IC660) BBD101 * BBD102 * BBD103 * BBD110 8 group quantity 8 groups 8 isolation (4 groups) 8 isolation (3 groups) 16 groups of nominal voltage 115Vac 115Vac 125Vdc 115Vac 125 Vdc 115Vac 115Vac Working mode SPLX/HSB SPLX/HSB-SPLX/HSB/HSB SIMPLEX AC voltage range (47 – 63Hz) 93 – 132 93 – 13 93 – 132 DC voltage range n/a 105 – 132 105 – 132 n/a P.S. Voltage drop time 1 cycle 10ms DC 1 cycle block isolation 1500V 1500V 1500V 1500V 1500V 1500V 1500V point status LED 1 per point 1 per point 1 diagnostic LED unit is normal (Block or point fault indication) - Enable (online and forced point indication) Turn on input diagnosis Yes Yes Yes Yes Yes Short circuit input diagnosis No Yes Power loss Block diagnosis Loss Yes Yes Block selectable filter time 10 – 100ms10 – 100 ms 10 – 100 ms Input impedance (typical) 13 K ohms 13 K ohm 11.6 K ohms AC on threshold (normal mode) 95 VRMS 95 VRMS programmable AC off threshold
