IS200TGENH1A DCS模块卡件,DCS卡件
具有两个24针连接器的32点模块的目录号为：IC693MDL654、IC693MDL 655、IC6913MDL752和IC693ML 753。模块输入的连接从用户的输入设备断开，连接到安装在模块前部的两个le（针型）24针连接器（Fujitsu FCN-365P024-AU）。安装在模块右侧的连接器（前视图）与A组和B组连接；模块左侧的连接器与C组和D组连接。如果连接到这些模块需要不同长度的电缆，您可以自己制作电缆（有关制作电缆的信息，请参阅电缆IC693CBL315的数据表）。A1 B1 A12 B12长度=10’（3米）连接器：Fujitsu FCN-365S024-AU图B-10。IC693CBL310电缆I/O电缆数据表C GFK-0898F附录应与热缩管绑在一起，以便于识别。例如，应在连接到引脚A1和A2等的黑色和白色（#1）周围放置一小段热缩管。更换/废弃信息该电缆已过时，并由电缆IC693CBL315（也已废弃）代替。这两条电缆的唯一区别在于颜色编码。当电缆IC693CBL315过时时，这些电缆的替代品变为IC693CBL 327和IC693CBL328。电缆IC693CBL310/315具有直接头。电缆IC693CBL327/328具有直角连接器。直角连接器要求PLC前面的深度较小，因此允许在某些应用中使用sller外壳。电缆IC693CBL315和IC693CBL 327/328的数据表见本章。C C-18 Series 90-30 PLC I/O模块规格–2000 GFK-0898F电缆IC693CBL310的连接器深度下图显示了当该电缆连接到模块时，PLC前面所需的空间。安装PLC的机柜的深度应允许此连接器添加的深度。2.187“1.5–2.5”典型PLC（侧视图）图B-11。PLC输入/输出电缆数据表C GFK-0898F附录C–32点模块的输入/输出线缆数据表C-19 IC693CBL315输入/输出接口线缆（24针）前连接器的深度尺寸te：该线缆于1998年底过时。它被两条电缆取代：IC693CBL327和IC693CBL 328。有关详细信息，请参阅这些电缆的数据表。替换电缆具有直角连接器，以减少PLC前面所需的间隙空间。电缆功能此pred电缆可用于所有使用富士通24针用户I/O连接器的90-30系列高密度（32点）I/O模块。
Catalog numbers for 32 point modules having two 24-pin connectors are: IC693MDL654, IC693MDL655, IC693MDL752, and IC693MDL753. Connections to module input s are de from the user’s input devices to two le (pin-type) 24-pin connectors (Fujitsu FCN-365P024-AU) mounted on the front of the module. The connector mounted on the right of the module (front view) interfaces with groups A and B; the connector on the left side of the module interfaces with groups C and D. If a different length cable is required for connections to these modules, you can build your own cable (infortion on building your own cable is found in the data sheet for cable IC693CBL315). A1 B1 A12 B12 Length = 10’ (3 meters) Connector: Fujitsu FCN-365S024-AU Figure B-10. IC693CBL310 Cable I/O Cable Data Sheets C GFK-0898F Appendix should be tied together with heat shrink tubing for identification purposes. For example, a short piece of heat shrink tubing should be placed around the BLACK and WHITE ( #1) that connect to Pins A1 and A2, etc. Replacement/Obsolescence Infortion This cable became obsolete and was replaced by cable IC693CBL315 (w obsolete also). The only difference between these two cables is in the color coding. When cable IC693CBL315 became obsolete, the replacement for these cables became IC693CBL327 and IC693CBL328. Cables IC693CBL310/315 have straight connectors. Cables IC693CBL327/328 have right angle connectors. The right angle connectors require less depth in front of the PLC, so allow the use of a sller enclosure in some applications. Data sheets for cables IC693CBL315 and IC693CBL327/328 can be found in this chapter. C C-18 Series 90-30 PLC I/O Module Specifications – 2000 GFK-0898F Connector Depth for Cable IC693CBL310 The following illustration shows the space required in front of the PLC when this cable is connected to a module. The depth of the cabinet that the PLC is mounted in should allow for the depth added by this connector. 2.187” 1.5–2.5” Typical PLC (Side View) Figure B-11. Dimensions for Depth of Connector in front of PLC I/O Cable Data Sheets C GFK-0898F Appendix C – I/O Cable Data Sheets C-19 IC693CBL315 I/O Interface Cable (24-Pin) for 32 Point Modules te: This cable became obsolete in late 1998. It was replaced by two cables: IC693CBL327 and IC693CBL328. See the data sheet for these cables for details. The replacement cables have right-angle connectors to reduce the clearance space required in front of the PLC. Function of cable This pred cable is ailable for use with all Series 90-30 high-density (32 point) I/O modules that use the Fujitsu 24-pin user I/O connector.
