IS200TRLYH2C机器人模块卡件
初始显示R0:03空>S要将IC693ALG392模块添加到配置中，请按读取/验证、ENT键序列。将显示以下屏幕：R0:03 AO 1.00>S I16:I_选择%I参考此时，必须输入从模块返回的状态数据的起始%I参考地址。注意，状态字段（16）的长度显示为显示器第二行第一个I之后的前两位数字。te此字段不能用手持式编程器更改。但是，可以使用Logicster 90-30/20/Micro软件配置器功能对其进行更改。手持式编程器将始终反映状态字段的当前有效长度。11 11-26 Series 90-30 PLC I/O模块规格–2000 GFK-0898F按下ENT键将允许PLC选择状态数据的起始地址。您可以通过按所需地址的键序列并按ENT键来选择特定的起始地址。例如，要将起始地址指定为I17，请按键序列1、7、ENT。将显示以下屏幕：R0:03 AO 1.00>S I16:I0017–I0032您可以随时按下CLR键中止刚刚选择的配置并将插槽返回为空。选择起始%I地址并按下ENT键后，出现以下屏幕。R0:03 AO 1.00>S AQ8:AQ_选择%AQ参考此屏幕允许您通过在%AQ字段中指定起始参考来选择%AQ引用的起始地址。您可以选择下一个可用地址（默认）或输入特定地址。按下ENT键将允许PLC选择起始地址。要输入特定地址（例如%AQ35），请按起始参考数字键和ENT键。例如，要指定%AQ35的起始地址，请按键序列3、5、ENT。R0:03 AO 1.00>S AQ8:AQ035–AQ043表示状态字段（8）的长度显示为显示第二行第一个AQ后的前两位数字。te此字段不能用手持式编程器更改。但是，可以使用Logicster 90-30/20/Micro软件配置器功能更改。手持式编程器将始终反映状态字段的当前有效长度。您可以随时按下CLR键中止刚才选择的配置，并将插槽返回为空。11 Alog模块GFK-0898F第11章–Alog模块11-27从配置中移除模块如果需要，可以从当前机架配置中移除此模块。假设模块当前配置在机架0插槽3中。可以按以下顺序删除：初始显示R0:03 AO 1.00>S AQ8:AQ_要删除模块，请按DEL，ENT键顺序。然后显示：R0:03 EMPTY>S如果在DEL键（而不是ENT键）之后按下了CLR键，则删除操作将被中止。选择模块默认模式模块的默认停止模式，HOLD（保持）或DEFLOW（除霜），可根据需要使用以下程序进行显示和修改。初始显示R0:03 AO 1.00>S I16:I0017–I0032要显示模块的默认STOP模式，请按→ →. 显示屏将显示模块的当前模式。默认模式为HOLD（保持）。R0:03 AO 1.00>S HLS/DEF:HOLD您可以通过按±键在HOLD（保持）和DEFLOW（除霜）模式之间切换。所选范围是当前显示的范围。R0:03 AO 1.00>S HLS/DEF：DEF LOW当屏幕上显示模块所需的模式时，按下ENT键即可接受。要返回上一屏幕，请按← 钥匙
Initial Display R0:03 EMPTY >S To add the IC693ALG392 module to the configuration, press the READ/VERIFY, ENT key sequence. The following screen will be displayed: R0:03 AO 1.00 >S I16:I_ Selecting %I Reference At this point the starting %I reference address for the status data returned from the module must be entered. tice that the length of the status field (16) is displayed as the first two digits following the first I on the second line of the display. te This field cant be changed with the Hand-Held programmer. However, it can be changed using the Logicster 90-30/20/Micro software configurator function. The Hand-Held Programmer will always reflect the currently active length of the status field. 11 11-26 Series 90-30 PLC I/O Module Specifications – 2000 GFK-0898F Pressing the ENT key will allow the PLC to select the starting address of the status data. You can select a specific starting address by pressing the key sequence for the desired address and pressing the ENT key. For example to specify the starting address as I17, press the key sequence 1, 7, ENT. The following screen will be displayed: R0:03 AO 1.00 >S I16:I0017–I0032 You can press the CLR key at any time to abort the configuration you have just selected and return the slot to EMPTY. After selecting the starting %I address and pressing the ENT key, the following screen appears. R0:03 AO 1.00 >S AQ8:AQ_ Selecting %AQ Reference This screen allows you to select the starting address for the %AQ reference by specifying the starting reference in the %AQ field. You can select the next ailable address (the default) or enter a specific address. Pressing the ENT key will allow the PLC to select the starting addresses. To enter a specific address (for example %AQ35), press the starting reference number keys and the ENT key. For example, to specify a starting address of %AQ35, press the key sequence 3, 5, ENT. R0:03 AO 1.00 >S AQ8:AQ035–AQ043 te that the length of the status field (8) is displayed as the first two digits following the first AQ on the second line of the display. te This field cant be changed with the Hand-Held programmer.However, it can be changed using the Logicster 90-30/20/Micro software configurator function. The Hand-Held Programmer will always reflect the currently active length of the status field. You can press the CLR key at any time to abort the configuration you have just selected and return the slot to EMPTY. 11 Alog Modules GFK-0898F Chapter 11 – Alog Modules 11-27 Removing Module From Configuration If required, this module can be removed from the current rack configuration. Assume that the module is currently configured in rack 0, slot 3. It can be deleted with the following sequence: Initial Display R0:03 AO 1.00 >S AQ8:AQ_ To delete the module, press the DEL, ENT key sequence. The display will then be: R0:03 EMPTY >S If the CLR key had been pressed after the DEL key (instead of the ENT key), the delete operation would have been aborted. Selecting Module Default Mode The default STOP mode of the module, either HOLD or DEFLOW, can be displayed and modified, if required, by using the following procedure. Initial Display R0:03 AO 1.00 >S I16:I0017–I0032 To display the module‘s default STOP mode, press → →. The display will show the current mode of the module. The default mode is HOLD. R0:03 AO 1.00 >S HLS/DEF:HOLD You can toggle between the HOLD and DEFLOW modes by pressing the ± key. The range selected is the one currently displayed. R0:03 AO 1.00 >S HLS/DEF:DEF LOW When the desired mode for the module is displayed on the screen it can be accepted by pressing the ENT key. To return to the previous screen, press the ← key.
