IS200TRLYH3E工控模块卡件
请注意，电流/电压模块对扫描时间的影响与您输入的对数直接相关。%AQ Ref Adr的唯一允许条目是%AQ地址。%I Ref Adr的唯一允许条目是%I地址。%I大小中的条目只接受8或16。此字段确定返回给用户的位数。%AQ Ref Adr字段是%AQ数据的参考地址，指向%AQ内存中数据到模块的起始位置。每个都提供16位模拟数据作为0到32760或–32767到32752的整数值。取决于所选择的范围类型。有关数据堡的详细信息，请参阅本手册中的Alog模块接口部分。%I Ref Adr是%I数据的参考地址，指向%I存储器（输入表）中报告模块状态信息的位置的起始位置。您可以通过编辑%I大小字段中的值来选择报告给PLC的%I状态位置的数量。%I大小字段中允许的值为8或16，表示报告给PLC的%I位置的数量。%I Ref Adr字段仅接受%I，用于%I大小值为8或更大；带回的数据如下：前八个%I位置（可用于%I尺寸值8、16）%I位置描述%I模块正常；0（零）表示T OK（T正常），1表示模块OK%I+1 User Supply OK（用户电源正常）-表示用户电源在指定范围内；当用户电源低于指定限制时读取0，当用户电源正常时读取1%I+2–%I+7为将来的模块保留。t在本模块中使用。第二个八个位置–（可用于%I尺寸值为16）%I位置描述%I+8可以选择四个范围之一。两个是电压范围。默认范围为V，其中电压值范围为伏，对应于Series 90-30的0至32000整数值。选择–10至+10V范围时，从–10至+10V的电压范围对应–32000至32000。两个电流范围为、和。在每个电流范围中，0到32000之间的值被发送到模块。根据选择的范围，将确定模块是处于电流模式还是电压模式。11 11-24 Series 90-30 PLC I/O模块规格–2000 GFK-0898F下表显示从发送到模块的值。量程模块模式*允许值V电压0至32767–10至10 V电压–32768至32767电流0至32000*电流0至32767*允许值是指盖上的值。如果用户发送的值大于32000，模块将在将其发送到D/a转换器之前将该值截断为32000。屏幕6上仅显示ebled（激活）。按下Shift-F1（机架）或Escape键返回机架显示。11 Alog模块GFK-0898F第11章–Alog模块11-25使用手持式编程器配置IC693ALG392您也可以使用90-30系列手持式编程仪配置8-Alog电流/电压模块。除本节中的信息外，有关智能I/O模块配置的更多信息，请参阅GFK-0402《手持式编程器用户手册》。尽管您可以使用Logicster 90-30/20/Micro配置器功能更改主动扫描的数量，但手持式编程器不支持编辑主动扫描的数目。如果手持式编程仪初始化8-高电流/电压模块，则主动扫描的数为8。如果先前已使用Logicster 90-30/20/Micro软件对模块进行了配置，且主动扫描的数量已从8变为8，则该数量将显示在AQ输入后手持式编程器显示屏的底行。您只能使用手持式编程器编辑活动s的数据，但不能更改活动扫描s的数量。模块存在如果系统中存在模块，则可以通过将模块读入配置文件将其添加到系统配置中。例如，假设一个8-Alog电流/电压模块安装在311型PLC系统的插槽3中。可以按以下顺序将其添加到配置中。使用↑ 和↓ 箭头光标键或#键显示所选插槽。
te that the impact of the Current/Voltage module on the scan time is directly proportiol to the number of alog s that you have ebled. The only allowable entries for the %AQ Ref Adr are %AQ addresses. The only allowable entries for the %I Ref Adr are %I addresses. The entry in %I Size will only accept 8 or 16. This field detes the number of bits returned to the user. The %AQ Ref Adr field is the reference address for the %AQ data and points to the start of the locations in the %AQ memory where the data to the module begins. Each provides 16 bits of alog data as an integer lue from 0 to 32,760 or –32,767 to 32,752. depending on the range type selected. For detailed infortion on the data fort, see the Interface to Alog Modules section in this nual. The %I Ref Adr is the reference address for the %I data and points to the start of the locations in the %I memory (the Input Table) where status infortion from the module is reported. You can select the number of %I status locations reported to the PLC by editing the lue in the %I Size field. lues allowable in the %I Size field are 8 or 16, which refer to the number of %I locations reported to the PLC. The %I Ref Adr field will only accept %I for %I Size lues 8 or greater; the data brought back is in the fort that follows: The first eight %I locations (ailable for %I SIZE lues 8, 16) %I Locations Description %I Module OK; a 0 (zero) indicates T OK, 1 indicates module OK %I+1 User Supply OK - Indicates when user supply is in specified limits; reads a 0 when user supply is below the specified limit, 1 when User supply is OK %I+2 – %I+7 Reserved for future modules. t used in this module. Second eight locations – (ailable for %I SIZE lue of 16) %I Locations Description %I+8 One of four ranges can be selected. Two are voltage ranges. The default range isV, where voltage lues ranging from volts correspond to 0 to 32000 integer lues from the Series 90-30 . The –10 to +10V range, when selected, corresponds from –32000 to 32000 from the over an voltage range of –10 to +10V. The two current ranges are , and . In each of the current ranges lues between 0 and 32000 are sent to the module. Depending on which range is selected, will determine if the module is in Current or Voltage mode. 11 11-24 Series 90-30 PLC I/O Module Specifications – 2000 GFK-0898F The following table shows lues sent from the to the module. Range Module Mode *Allowed lues V Voltage 0 to 32767 –10 to 10 V Voltage – 32768 to 32767 Current 0 to 32000* Current 0 to 32767 *Allowed lues refers to the lues that are lid. If a user sends a lue > 32000, the module will truncate that lue to 32000 before sending it to the D/A Converter. te Only ebled (active) s are displayed on the screen 6. Press Shift-F1 (Rack) ) or the Escape key to return to the rack display. 11 Alog Modules GFK-0898F Chapter 11 – Alog Modules 11-25 Configuring IC693ALG392 with Hand-Held Programmer You can also configure the 8- Alog Current/Voltage module using the Series 90-30 Hand-Held Programmer. In addition to the infortion in this section, refer to GFK-0402, the Hand-Held Programmer User’s nual for more infortion on configuration of Intelligent I/O modules. Although you can change the number of actively scanned s with the Logicster 90-30/20/Micro configurator function, the Hand-Held Programmer does t support editing the number of actively scanned s. If the 8- Alog Current/Voltage module is initialized by a Hand-Held Programmer, the number of actively scanned s is 8. If a module had been previously configured with Logicster 90-30/20/Micro software and the number of actively scanned s has been changed from 8, that number will be displayed on the bottom line of the Hand-Held Programmer display following the AQ entry. You can edit data with the Hand-Held Programmer only for the active s, but you can t change the number of actively scanned s. Module Present If a module is physically present in a system, it can be added to the system’s configuration by reading the module into the configuration file. For example, assume that an 8- Alog Current/Voltage module is installed in slot 3 of a Model 311 PLC system. It can be added to the configuration with the following sequence. Use the ↑ and ↓ arrow cursor keys or the # key to display the selected slot.
