IS200TRTDH1C模块控制器,处理器模块
例如，假设一个16-Alog电流输入模块安装在311型PLC系统的插槽3中。可以按以下顺序将其添加到配置中。使用向上和向下光标键或#键显示选定的插槽。初始显示R0:03 EMPTY>S要将IC693ALG223模块添加到配置中，请按READ/VIFY键。将显示以下屏幕：R0:03 HI–DEN C>S I40:I_选择%I参考此时，必须输入从模块返回的状态数据的起始%I参考地址。注意，状态字段（40）的长度显示为显示器第二行第一个I之后的前两个数字。10 10-36 Series 90-30 PLC I/O模块规格–2000 GFK-0898F te此字段不能用手持式编程器更改。但是，可以使用Logicster 90-30/20/20/Micro软件配置器功能对其进行更改。手持式编程器将始终反映状态字段的当前有效长度。按下ENT键将允许PLC选择状态数据的起始地址。您可以通过按所需地址的键序列并按ENT键来选择特定的起始地址。例如，要将起始地址指定为I17，请按键序列1、7、ENT。将显示以下屏幕：R0:03 HI–DEN C>S I40:I17–I56选择%AI参考在选择了起始%I地址后，再次按下ENT键将显示如下屏幕：R0:0.3 HI–DEN C>S AI16:AI_此屏幕允许您为%AI参考选择起始地址。状态字段（16）的长度显示为显示器第二行上第一AI之后的前两位数字。te此字段不能用手持式编程器更改。但是，可以使用Logicster 90-30/20/Micro软件配置器功能对其进行更改。手持式编程器将始终反映状态字段的当前有效长度。在AI字段中，您可以通过按下ENT键或输入特定地址来选择下一个可用地址（默认）。要输入特定地址，请按起始参考数字键和ENT。钥匙（例如，3、5，然后ENT.R0:03 HI–DEN C>S AI16:AI035–AI051）您可以随时按下CLR键中止刚刚选择的配置，并将插槽返回空。Alog输入模块10 GFK-0898F第10章–Alog输入模件10-37从配置中移除模块如果需要，可以从当前配置中移除此模块。假设模块当前为空y配置在机架0插槽3中。可以按以下顺序删除：初始显示R0:03 HI–DEN C>S AI16:AI_要删除模块，请按DEL，ENT键顺序。然后显示为：R0:03 EMPTY>S Selecting Input Ranges（R0:03空>S选择输入范围）16 S中每一个的范围都可以显示并选择或更改，如下所述。假设%AI地址与先前选择的相同。初始显示R0:03 HI–DEN C>S AI16:AI035–AI051要显示范围，请按→ 钥匙显示屏将显示1（或当前选定的）和第一个可用范围。R0:03 HI–DEN C>S 1:4–20您可以通过按±键切换每个值的范围。每个范围将显示如图所示。所选范围是当前显示的范围。R0:03 HI–DEN C>S 1:0–20 R0:03 HI-DEN C>S 1:4–20+报警限值显示要查看当前显示的报警限值，请按→ 再次按键（第一次使范围可用于编辑）。
For example, assume that a 16- Alog Current Input module is installed in slot 3 of a Model 311 PLC system. It can be added to the configuration with the following sequence. Use the Up and Down cursor keys or the # key to display the selected slot. Initial Display R0:03 EMPTY >S To add the IC693ALG223 module to the configuration, press the READ/VERIFY key. The following screen will be displayed: R0:03 HI–DEN C >S I40:I_ Selecting %I Reference At this point the starting %I reference address for the status data returned from the module must be entered. tice that the length of the status field (40) is displayed as the first two digits following the first I on the second line of the display. 10 10-36 Series 90-30 PLC I/O Module Specifications – 2000 GFK-0898F te This field cant be changed with the Hand-Held programmer. However, it can be changed using the Logicster 90-30/20/20/Micro software configurator function. The Hand-Held Programmer will always reflect the currently active length of the status field. Pressing the ENT key will allow the PLC to select the starting address of the status data. You can select a specific starting address by pressing the key sequence for the desired address and pressing the ENT key. For example to specify the starting address as I17, press the key sequence 1, 7, ENT. The following screen will be displayed: R0:03 HI–DEN C >S I40:I17–I56 Selecting %AI Reference After the starting %I address has been selected, pressing the ENT key again will cause the following screen to be displayed: R0:03 HI–DEN C >S AI16:AI_ This screen allows you to select the starting address for the %AI reference. te that the length of the status field (16) is displayed as the first two digits following the first AI on the second line of the display. te This field cant be changed with the Hand-Held programmer. However, it can be changed using the Logicster 90-30/20/Micro software configurator function. The Hand-Held Programmer will always reflect the currently active length of the status field. In the AI field you can select the next ailable address (the default) by pressing the ENT key or by entering a specific address. To enter a specific address, press the starting reference number keys and the ENT. key (for example 3, 5, then ENT. R0:03 HI–DEN C >S AI16:AI035–AI051 You can press the CLR key at any time to abort the configuration you have just selected and return the slot to EMPTY. Alog Input Modules 10 GFK-0898F Chapter 10 – Alog Input Modules 10-37 Removing Module From Configuration If required, this module can be removed from the current configuration. Assume that the module is currently configured in rack 0, slot 3. It can be deleted with the following sequence: Initial Display R0:03 HI–DEN C >S AI16:AI_ To delete the module, press the DEL, ENT key sequence. The display will then be: R0:03 EMPTY >S Selecting Input Ranges The range for each of the 16 s can be displayed and selected or changed as described below. Assume that the %AI address is as previously selected. initial display R0:03 HI–DEN C >S AI16:AI035–AI051 To display the ranges press the → key. The display will show 1 (or the currently selected ) and the first ailable range. R0:03 HI–DEN C >S 1: 4–20 You can toggle through the range for each by pressing the ± key. Each range will be displayed as shown. The range selected is the one currently displayed. R0:03 HI–DEN C >S 1: 0–20 R0:03 HI–DEN C >S 1: 4–20+ Alarm Limits Display To view the alarm limits for the currently displayed, press the → key again (the first time caused the ranges to be ailable for editing).
