IS200TTURH1B输出卡件,DCS模块卡件
也可以使用CIMPLICITY控制编程软件进行配置。有关详细信息，请参阅CIMPLICITY Control联机帮助。要在I/O配置机架屏幕上配置16-Alog电压输入模块：1。将光标移动到模块所在的插槽，然后按下m30 io软键（F1）。在以下示例屏幕中，模块将放置在机架内的插槽5中。2.按下软键（F4）显示可用模拟输入模块列表及其目录号。Alog输入模块10 GFK-0898F第10章–Alog输入模件10-19 3。要选择16-Alog电压输入模块，将光标放在模块的目录号IC693ALG222上，然后按Enter键。4.按下Enter键后，将显示如下所示的第一个详细屏幕。然后，您可以根据应用程序的需要配置模块。屏幕5上仅显示ebled（激活）。使用下表中提供的参数说明帮助您在此屏幕上选择参数。10 10-20系列90-30 PLC I/O模块规格–2000 GFK-0898F表10-6。配置参数说明参数说明激活输入一个从1*到16的数字（单端）或1*到8的数字（差分）。此数字表示要转换的数量。以连续的顺序扫描。1是第一次扫描。如果选择了八个以上，将显示第二个详细信息屏幕，允许您在第9到第16中输入数据。参考地址第一个参考地址字段包含%AI数据的参考地址。地址指向%AI内存中模块输入数据开始的位置。根据所选的范围类型，每一个都提供16位模拟输入数据作为从0到32760或–32767到32752的整数值。引用地址第二个引用地址字段包含%I数据的引用地址。地址指向%I内存中模块状态信息开始的位置。您可以通过编辑%I大小字段中的值来选择报告给PLC的%I状态位置的数量。模式模式字段描述用户需要连接到终端板的类型。在*单端模式中，有16个输入参考单个。在差分模式下，8个输入中的每一个都有自己的sigl和，因此每个输入都使用端子板上的两个点。输入报告给PLC的%I位置的数量。选项为用户电源正常。%I+2到%I+7=为将来的模块保留。第二个8%I位置：Alog输入模块10 GFK-0898F第10章–Alog输入单元10-21表10–6。配置参数说明（续）参数说明%I大小（续）第五个%I位置：（可用于%I大小值40）范围选择范围。选项为*0至10V或–10至10V。在V默认范围内，输入电压值范围从V报告0到32000整数值到。
Configuration can also be done using CIMPLICITY Control Programming Software. For details refer to the CIMPLICITY Control online help. To configure a 16- Alog Voltage Input Module on the I/O Configuration Rack screen: 1. Move the cursor to the slot where the module will be located, and press the m30 io softkey (F1). In the following example screen, the module will be placed in slot 5 of the in rack. 2. Press the a in, softkey (F4) to display a list of ailable alog input modules and their catalog numbers. Alog Input Modules 10 GFK-0898F Chapter 10 – Alog Input Modules 10-19 3. To select the 16- Alog Voltage Input Module, position the cursor on the catalog number for the module, IC693ALG222, and press the Enter key. 4. After pressing the Enter key, the first detail screen, shown below, is displayed. You can then configure the module as required for your application. te Only ebled (active) s are displayed on the screen 5. Use the parameter descriptions provided in the following table to help you ke selections for the parameters on this screen. 10 10-20 Series 90-30 PLC I/O Module Specifications – 2000 GFK-0898F Table 10-6. Parameter Descriptions for Configuration Parameter Description Active Enter a number from 1* through 16 for Single Ended or 1* through 8 for Differential. This number represents the number of s to be converted. s are scanned in sequential, contiguous order, with . 1 being the first scanned. If more than eight s are selected, a second detail screen will be displayed to allow you to enter data in s 9 through 16. Reference Address The first Reference Address field contains the reference address for %AI data. The address points to the location in %AI memory where input data to the module begins. Each provides 16 bits of alog input data as an integer lue from 0 to 32,760 or –32,767 to 32,752, depending on the range type selected. Reference Address The second Reference Address field contains the reference address for %I data. The address points to the location in %I memory where status infortion from the module begins. You can select the number of %I status locations reported to the PLC by editing the lue in the %I Size field. Mode The Mode field describes what type user connection to the termil board is desired. In *Single Ended mode, there are 16 inputs referenced to a single . In Differential mode each of the 8 inputs has its own sigl and , thereby using two points on the termil board for each . Enter the number of %I locations reported to the PLC. Choices are user supply OK. %I+2 through %I+7 = Reserved for future modules. Second eight %I locations: Alog Input Modules 10 GFK-0898F Chapter 10 – Alog Input Modules 10-21 Table 10–6. Parameter Descriptions for Configuration (continued) Parameter Description %I Size (cont’d) Fifth eight %I locations: (ailable for %I SIZE lue 40) Range Select the range. Choices are *0 to 10V or –10 to 10V. In theV default range, input voltage lues ranging fromV report 0 to 32,000 integer lues to the .
