IS200VAICH1CBR脉冲输入卡件
从s到用户负载设备的连接通过安装在模块前部的两个le（针型）24针连接器（Fujitsu FCN-365P024-AU）断开。安装在模块右侧的连接器（前视图）与A组和B组连接。模块左侧的连接器与C组和D组连接。现场设备直接接线法–该方法使用的电缆在模块端部有一个毛毡连接器，在另一端有剥线和镀锡。您可以购买一条预先订购的电缆，目录号为IC693CBL327和IC693CBL 328，或者，如果您的应用需要，您可以自己制作电缆。有关更多信息，请参阅本手册附录C中IC693CBL327/328数据表中的24针连接器建筑电缆。使用TBQC–Termil Block快速连接方法使用一条电缆，每端带有连接器。这些连接器从模块连接器连接到DIN导轨安装端子块上的连接器。TBQC组件见附录D.7 7-50系列90-30 PLC I/O模块规范–2000 GFK-0898F表7-24。IC693MDL753额定电压范围12至24伏直流电的规范，正逻辑10.2至28.8伏直流电/模块隔离32（四组，每组8个）1500伏场侧和逻辑侧之间250伏组间电流0.5每点，每组4个，每组3个引脚特性10毫秒的浪涌电流5.4开状态电压降0.3伏直流关状态漏电电流0.1开响应时间0.5毫秒关响应时间0.5 ms联锁电源背板上5伏总线的消耗260；（13+3/点开+4.7/LED）用户电源@24时每组16.5个，组内所有8个开启@12时每组9.6个，组中所有8个打开参考数据表GFK-0867C或更高版本的产品标准和一般规范。OCS模式1模式0 5V 0V RUN（FROM）xCOM PTx a47069稳压器xVIN 0V 5V LED典型离散模块7 GFK-0898F第7章-离散模块7-51 IC693MDL753模块现场接线信息下图提供了将用户提供的负载设备和电源连接到正逻辑模块的接线信息。模块点数以粗体文本显示。模块点数以粗体文本显示。图7-41。现场接线-12/24 V DC，0.5A正逻辑32点模块-IC693MDL753 7 7-52系列90-30 PLC I/O模块规格–2000 GFK-0898F IC693MDL 753现场接线工作表提供下表以方便客户使用电缆IC693CBL315接线24针连接器。它在一个表格中包含所有所需的接线信息。此表包含以下信息：模块点编号：A1-A8、B1-B8、C1-C8、D1-D8、电压和点连接器引脚编号：A1至A12、B1至B12电缆编号：1至12颜色代码：基色或带示踪色的基色。还提供了列供参考和客户编号。在为12/24伏直流、0.5A正逻辑、32点模块接线时，请根据需要复制并使用本页和下页的工作表。模块组A和B（模块右前方的连接器）的接线参考模块点编号连接器引脚编号电缆编号颜色代码8输入/8 s
Connections from the s are de to the user load devices from two le (pin-type) 24-pin connectors (Fujitsu FCN-365P024-AU) mounted on the front of the module. The connector mounted on the right of the module (front view) interfaces with groups A and B. The connector on the left side of the module interfaces with groups C and D. Wiring to Field Devices Direct Method – This method uses cables that have a ting fele connector on the module end and stripped and tinned s on the other end. You can purchase a of pre-d cables, catalog numbers IC693CBL327 and IC693CBL328 or, if required for your application, build your own cables. Refer to Building Cables for 24-Pin Connectors in the IC693CBL327/328 data sheet in Appendix C of this nual for more infortion. Using a TBQC – The Termil Block Quick Connect method uses a of cables with connectors on each end. These connect from the module connectors to connectors on DIN–rail mounted termil blocks. The TBQC components are discussed in Appendix D. 7 7-50 Series 90-30 PLC I/O Module Specifications – 2000 GFK-0898F Table 7-24. Specifications for IC693MDL753 Rated Voltage Voltage Range 12 through 24 volts DC, positive logic 10.2 to 28.8 volts DC s per Module Isolation 32 (four groups of eight s each) 1500 volts between field side and logic side 250 volts between groups Current 0.5 per point with 4 per group and 3 per group pin Characteristics Inrush Current 5.4 for 10 ms On-state Voltage Drop 0.3 volts DC Off-state Leakage Current 0.1 On Response Time 0.5 ms Off Response Time 0.5 ms Interl Power Consumption 260 from 5 volt bus on backplane; (13 + 3 /point ON + 4.7 /LED) 16.5 per group from user supply @ 24 and all eight s in group ON 9.6 per group from user supply @ 12 and all eight s in group ON Refer to data sheet GFK-0867C, or later revision for product standards and general specifications. OCS MODE 1 MODE 0 5V 0V RUN (FROM ) xCOM PTx a47069 REGULATOR xVIN 0V 5V LED TYPICAL Discrete Modules 7 GFK-0898F Chapter 7 – Discrete Modules 7-51 IC693MDL753 Module Field Wiring Infortion The following figure provides wiring infortion for connecting user supplied load devices and power source to positive logic module. Module point numbers are shown in bold text. MODULE POINT NUMBERS ARE SHOWN IN BOLD TEXT. Figure 7-41. Field Wiring - 12/24 Volt DC, 0.5A Positive Logic 32 Point Module - IC693MDL753 7 7-52 Series 90-30 PLC I/O Module Specifications – 2000 GFK-0898F Field Wiring Work Sheet for IC693MDL753 The following table is provided for the convenience of our customers as an aid to wiring the 24-pin connectors using cable IC693CBL315. It includes all of the required wiring infortion in one table. This table has the following infortion: module point number: A1 - A8, B1 - B8, C1 - C8, D1 - D8, voltage and points connector pin number: A1 through A12, and B1 through B12 cable number: 1 through 12 color code: base color or base color with tracer color Columns are also provided for references and customer numbers. Please copy and use the work sheets on this and the following page as needed when wiring the 12/24 Volt DC, 0.5A Positive Logic, 32 Point module. Wiring for Module Groups A and B (connector on right front of module) Reference Module Point Number Connector Pin Number Cable Number Color Code 8 Inputs/8 s
