IS200VCCCH1B自动化模块备件
LED指示灯位于模块顶部，指示每个点的开/关状态。该LED块具有两个水平行，每行中有八个绿色LED，顶行标记为A1至8（点1至8）。铰链门的内外表面之间有一个插件。朝向模块内部的表面（当铰链门关闭时）具有接线信息，并且识别信息可以记录在外表面上。插件的左外边缘为蓝色，表示低压模块。此模块上有保险丝。该模块可安装在Series 90-30 PLC系统中5或10插槽基板的任何I/O插槽中。表7-12。IC693MDL740额定电压12/24伏DC电压范围12至24伏DC（+20%，-15%）s每个模块16（两组，每组8个）场侧和逻辑侧之间的隔离1500伏组间500伏每点电流0.5每特性浪涌电流4.78 10毫秒压降1伏关断状态漏电1开响应时间2毫秒关断响应时间2 ms电源背板上5伏总线的消耗量110（全部打开）。有关产品标准和一般规范，请参阅附录B。离散模块7 GFK-0898F第7章-离散模块7-25 IC693MDL740模块现场接线信息下图提供了将用户提供的负载设备和电源连接到12/24伏直流正逻辑-0.5安培模块的接线信息。TERMILS现场布线1 3 5 7 9 11 13 15 17 19 4 8 10 14 16 18 20 12 2 6 a43098 A2 A3 A4 A5 A6 A7 A8 A1+B2 B3 B4 B5 B6 B7 B8 B1+1 f模块RY其他Sµ图7-22。IC693MDL740模块现场接线4 3 2 1 10 20 30 40 50 60总模块负载电流环境温度a45049（）图7-23。IC693MDL740 7 7-26 Series 90-30 PLC I/O模块规格的负载电流与温度–2000 GFK-0898F 12/24 V DC负逻辑0.5 Amp-16点IC693MDL 741 Series 90-30可编程逻辑控制器的12/24 V直流负逻辑0.5安培模块提供两组16点。每组有一个电源端子。该模块设计为具有负逻辑特性，因为它将电流从负载吸收到用户或负电源总线。该设备连接在正电源总线和模块之间。该特性与广泛的用户提供的负载设备兼容，例如：电机起动器、定子和指示器。操作现场设备的电源必须由用户提供。LED指示灯位于模块顶部，指示每个点的开/关状态。该LED块具有两个水平行，每行中有八个绿色LED；顶行标记为A1至8（点1至8），底行标记为B1至8（点9至16）。铰链门的内外表面之间有一个插件。朝向模块内部的表面（当铰链门关闭时）具有接线信息，并且识别信息可以记录在外表面上。插件的左外边缘为蓝色，表示低压模块。此模块上有保险丝。该模块可安装在Series 90-30 PLC系统中5或10插槽基板的任何I/O插槽中。表7-13。IC693MDL741额定电压12/24伏DC电压范围12至24伏DC（+20%，-15%）s每个模块16（两组，每组8个）场侧和逻辑侧之间的隔离1500伏组间500伏每点电流0.5伏每个特性电压降0.5伏关断状态漏电1开响应时间2毫秒关断响应时间2 ms功耗110（所有打开）从背板上的5伏总线，参考附录B了解产品标准和一般规范。离散模块7 GFK-0898F第7章-离散模块7-27 IC693MDL741模块现场接线信息下图提供了将用户提供的负载设备和电源连接到
LED indicators which provide the ON/OFF status of each point are located at the top of the module. This LED block has two horizontal rows with eight green LEDs in each row with the top row labeled A1 through 8 (points 1 through 8) and the bottom row labeled B1 through 8 (points 9 through 16). An insert goes between the inside and outside surface of the hinged door. The surface towards the inside of the module (when the hinged door is closed) has wiring infortion, and identification infortion can be recorded on the outside surface. The outside left edge of the insert is color-coded blue to indicate a low-voltage module. There are fuses on this module. This module can be installed in any I/O slot of a 5 or 10-slot baseplate in a Series 90-30 PLC system. Table 7-12. Specifications for IC693MDL740 Rated Voltage 12/24 volts DC Voltage Range 12 to 24 volts DC (+20%, –15%) s per Module 16 (two groups of eight s each) Isolation 1500 volts between field side and logic side 500 volts between groups Current 0.5 per point 2 per Characteristics Inrush Current 4.78 for 10 ms Voltage Drop 1 volt Off-state Leakage 1 On Response Time 2 ms Off Response Time 2 ms Power Consumption 110 (all s on) from 5 volt bus on backplane Refer to Appendix B for product standards and general specifications. Discrete Modules 7 GFK-0898F Chapter 7 – Discrete Modules 7-25 IC693MDL740 Module Field Wiring Infortion The following figure provides wiring infortion for connecting user supplied load devices and power source to the 12/24 volt DC positive logic - 0.5 amp module. TERMILS FIELD WIRING 1 3 5 7 9 11 13 15 17 19 4 8 10 14 16 18 20 12 2 6 a43098 A2 A3 A4 A5 A6 A7 A8 A1 + B2 B3 B4 B5 B6 B7 B8 B1 + 1 f MODULE RY OTHER S µ Figure 7-22. IC693MDL740 Module Field Wiring 4 3 2 1 10 20 30 40 50 60 TOTAL MODULE LOAD CURRENT AMBIENT TEMPERATURE a45049 () Figure 7-23. Load Current vs. Temperature for IC693MDL740 7 7-26 Series 90-30 PLC I/O Module Specifications – 2000 GFK-0898F 12/24 Volt DC Negative Logic 0.5 Amp - 16 Point IC693MDL741 The 12/24 volt DC Negative Logic 0.5 Amp module for the Series 90-30 Programble Logic Controller provides 16 points in two groups. Each group has a power termil. This module is designed to have negative logic characteristics in that it sinks current from the loads to the user or negative power bus. The device is connected between the positive power bus and the module . The characteristics are compatible with a wide range of user-supplied load devices, such as: motor starters, soleids, and indicators. Power to operate the field devices must be supplied by the user. LED indicators which provide the ON/OFF status of each point are located at the top of the module. This LED block has two horizontal rows with eight green LEDs in each row; the top row labeled A1 through 8 (points 1 through 8)and the bottom row labeled B1 through 8 (points 9 through 16). An insert goes between the inside and outside surface of the hinged door. The surface towards the inside of the module (when the hinged door is closed) has wiring infortion, and identification infortion can be recorded on the outside surface. The outside left edge of the insert is color-coded blue to indicate a low-voltage module. There are fuses on this module. This module can be installed in any I/O slot of a 5 or 10-slot baseplate in a Series 90-30 PLC system. Table 7-13. Specifications for IC693MDL741 Rated Voltage 12/24 volts DC Voltage Range 12 to 24 volts DC (+20%, –15%) s per Module 16 (two groups of eight s each) Isolation 1500 volts between field side and logic side 500 volts between groups Current 0.5 per point 2 per Characteristics Voltage Drop 0.5 volts Off-state Leakage 1 On Response Time 2 ms Off Response Time 2 ms Power Consumption 110 (all s on) from 5 volt bus on backplane Refer to Appendix B for product standards and general specifications. Discrete Modules 7 GFK-0898F Chapter 7 – Discrete Modules 7-27 IC693MDL741 Module Field Wiring Infortion The following figure provides wiring infortion for connecting user supplied load devices and power source to the
