IS210AEBIH2BEC工业自动化卡件
r继电器连接等，直到找到故障源。顺序事件记录器SER DOIO功能指令这些可以设置为在接收到触发信号时捕获指定离散地址的状态。它们可以被用来监视和捕获程序的某些部分的数据，即使在使用时也是如此。它们可用于查找侵入性问题的原因。例如，一个触点串中的一个触点，它随时为线圈供电，瞬间打开并中断操作。然而，当内部人员发现问题时，所有这些触点都正常。通过使用SER或DOIO指令，可以在故障发生后的几毫秒内捕获所有这些触点的状态，并且打开的触点将在捕获时显示逻辑状态。innce和Troubshooting Q apr innce和troubshootingReplacement s不包含配置swis。每个机架中的插槽使用配置软件进行配置，该软件具有特定的类型目录号。此配置信息存储在内存中。因此，在更换时，您不需要对其本身进行任何硬件设置。但是，您必须确保在特定插槽中安装正确的类型。请注意，PCM APM或DSM等某些插件可能包含在更换后需要重新加载的应用程序。例如，请确保保留应用程序的更新副本，以防它们被重新复制。对于带有板的，您没有新的板来替换。如果旧电路板没有缺陷，则可以从旧电路板上拆下，然后重新安装到新电路板上，而无需拆下任何接线。拆卸和安装s和板的程序见apr。产品Re产品在很大程度上被认为是现场的。一个主要的例外是少数具有可更换保险丝的保险丝。下一节保险丝列表列出了这些保险丝及其适用保险丝。GE通过您当地的经销商提供复制品保修服务。有关详细信息，请联系您的发行商。安装和硬件八月Q保险丝列表警告仅更换正确尺寸和类型的保险丝。使用不正确的保险丝可能会导致人员和/或设备受伤。表。s目录号的保险丝列表
elay connections etc. until the source of the fault is found. Sequential Event Recorder SER DOIO functiol instruction These can be set up capture the status of specified discre addresses upon receiving a trigger sigl. They y be used monir and capture data about certain portions of the program even when utnded. They can be useful for locating the cause of an inrmitnt probm. For examp a contact in a string of contacts that intain power a coil y from time time momentarily open and inrrupt rl operation. However when innce personnel atmpt loca the probm all of these contacts y st OK. By using the SER or DOIO instruction the status of all of these contacts can be captured within milliseconds of the time the fault occurs and the contact that opened will show a status of logic at the moment of capture. innce and Troubshooting Q apr innce and Troubshooting Replacing s s do t contain configuration swis. The slot in ea rack is configured using the configuration software hold a particular type catalog number. This configuration infortion is sred in memory. Therefore when replacing a you do t have ke any hardware settings on the itself. You do however have ensure that you install the correct type in a particular slot. Be aware that some inlligent s su as the PCM APM or DSM y contain application programs that will need be reloaded afr the is replaced. For su s ke sure that upda copies of the application programs are intained in case they have be resred lar. For s with boards you do t have re a new board in order replace the . If the old board is t defective it can be removed from the old and reinstald on the new without removing any of the wiring. Procedures for removing and installing s and boards are found in apr . Product Re The products are for the most part t considered be fieldreab. The one jor exception are the few s that have replaceab fuses. The next section Fuse List identifies these s and their applicab fuses. GE offers a reproduct warranty service through your local distribur. Contact your distribur for details. Installation and Hardware August Q Fuse List Warning Replace fuse only with the correct size and type. Using an incorrect fuse can result in harm personnel dage equipment or both. Tab . Fuse List for s Catalog Number
