IS210AEBIH3BBC工控模块备件
验证硬件是否正常工作。配置屏幕通常从sysm文档中获得以下信息。但是，如果它们可用，则可以使用配置屏幕：•如果软件配置是实际的硬件。有时，whi troublshoot a错误地安装在错误的插槽中。这将在两个故障选项卡之一中创建一个故障。可以从配置屏幕中确定正确的配置。•特定对象正在使用的内存地址。故障选项卡有两个故障选项卡：故障选项卡和IO故障选项卡。可以使用编程软件查看故障选项卡。这些故障选项卡不会将某些情况报告为有缺陷的限制开关，但会将系统故障识别为：•系统配置缺失或缺失。•硬件故障低电池•软件故障程序ecksum故障用户程序Sre故障。系统状态参考这些离散参考S SA SB和SC可以在系统参考状态选项卡中查看，如果在梯形图程序中使用，则可以在屏幕上查看，以确定严重条件和故障的状态。例如，如果任一故障选项卡中记录了故障，则SC位将打开。例如，如果内存备份电量较低，则SA位将开启。指令集参考包括一个系统状态参考选项卡。安装和硬件八月Q参考选项卡有两种类型的参考选项卡标准和混合。这些选项卡显示内存地址组及其状态。对于离散地址，这些地址的状态将显示为逻辑或逻辑。将显示alog和regisr地址的值。标准选项卡仅显示一种类型的内存地址su作为所有I位。混合引用选项卡由用户创建，用户指定选项卡中显示的地址。这些混合选项卡可以在一个选项卡中包含离散和注册引用。这使得它们在一个屏幕上收集多个关联地址时非常有用，可以同时查看或监视这些地址。与搜索或滚动梯形逻辑屏幕查找这些地址相比，这节省了时间。超控功能必须谨慎使用该功能，以确保人员和设备的安全。rlly线路不应该是循环的，所有条件都应该确保设备可以打开而不会造成任何伤害。该方法可用于从梯形图屏幕一直控制设备。例如，当覆盖和切换Q和ON状态时，继电器正弦曲线或其他受控设备应打开或拾取。如果没有，则可以检查上的状态灯，然后可以在板上进行电压检查，系统剥离，惰性剥离，或
verify that the hardware is working properly. Configuration Screens rlly the following infortion is obtained from the sysm documentation. However if they are t ailab the configuration screens can be used dermine: • If the software configuration s the actual hardware. Sometimes whi troubshooting a is instald in an incorrect slot by mistake. This will crea a fault in one of the two fault tabs. The correct configuration can be dermined from the Configuration Screens. • The memory addresses that a particular is using. Fault Tabs There are two fault tabs the Fault Tab and the IO Fault Tab. The fault tabs can be viewed using the programming software. These fault tabs will t report su things as a defective limit swit but will identify sysm faults su as: • Loss of or Missing s Sysm Configuration Mist. • hardware failure Low Batry • Software Failure Program ecksum Failure User Program Sre Failures. Sysm Status References These discre references S SA SB and SC can be viewed in the Sysm Reference Status Tab or onscreen if used in the ladder program for dermining the status of rious conditions and faults. For examp the SC bit turns on if a fault is logged in either fault tab. Ather examp is that bit SA will turn on if the memory backup batry is low. The Instruction Set Reference includes a Sysm Status Reference Tab. Installation and Hardware August Q Reference Tabs There are two types of reference tabs standard and mixed. These tabs show groups of memory addresses and their status. For discre addresses the status of these will be shown as either logic or logic . For alog and regisr addresses lues will be displayed. Standard tabs display only one type of memory address su as all of the I bits. Mixed reference tabs are cread by the user who sects what addresses display in the tabs. These mixed tabs can contain discre alog and regisr references all in one tab. This kes them useful for gathering numerous relad addresses on one screen where they can all be viewed or monired at the same time. This saves time pared with searing or scrolling through the ladder logic screens find these addresses. Override feature This feature must be used with caution ensure the safety of personnel and equipment. rlly the ine should t be cycling and all conditions should be su that the device can be turned on without any harm being done. This method can be used eck an from the ladder screen all the way the device being controld. For examp when overriding and ggling a Q an ON sta the relay soid or other device being controld should turn on or pick up. If it does t the status light on the could be ecked then voltage ecks could be de at the board the sysm strip the inery strip the soid or
