IS210AEDBH3ADC通用电气卡件,自动化卡件
通过FIP Remo扫描器的总线。每个远程分接器可以包括一个或一个机架中的插槽或插槽扩展机架以及任何离散和模拟的组合。通用设备例如通过FIP接口进入总线的通用设备。Q apr选项FIP总线控制器是标准机架。它很容易插入背板。底部的平台将其固定到位。引脚FIP现场总线引脚FIP总线引脚串行RS正常运行载波Dect。发送Eb。承运人声明。发送Eb。图。FIP总线控制器上设置了DIP开关或跳线。FIP总线控制器有六个状态D，一个RS串行端口和两个相同的FIP总线。状态D FIP总线控制器前面的D显示状态和活动。串行端口引脚串行端口用于连接一个pur，用于升级总线控制器的操作固件并通过exrl配置ol进行配置。FIP总线FIP总线控制器上的两个引脚提供一个或两个FIP总线的连接。两条总线提供冗余总线功能。安装和硬件八月Q ICBEM FIP Remo扫描仪FIP Facry Instrumentation Procol Remo扫描仪目录号ICBEM是一种面向FIP总线的插件。通过使用扩展驾驶室连接的两个插槽，可以实现升级。连同雷莫扫描仪及其服务的被称为Nest。FIP Nest可以包含大多数。主机CPU可以是能够在FIP总线上通信的任何类型的CPU。主机su中的A作为FIP总线控制器提供FIP总线和主机CPU之间的必要接口。FIP总线控制器CPU FIP总线主机CPU上设备Nest手持式编程器扩展驾驶室上脚Mers扫描仪图。FIP Remo扫描仪系统配置示例手持编程器提供了一种方便的方式来执行设置监控和控制功能。Remo扫描仪的功能FIP Remo扫描仪执行以下基本功能：“在secd模式下控制嵌套的操作”扫描离散和模拟并保持扫描定时“ps data FIP application riabs”检测和系统故障并报告FIP网络“允许使用手持编程器进行独立配置”保留其网络配置通过断电Q apr选项“允许手持式编程器强制执行”检测和记录输入转换“支持FIP消息服务”响应一个exrl同步信号“可以提供闪烁或脉冲信号”可以提供输入过滤和检测FIP总线接口远程扫描仪通信，数据速率为MHz。FIP标准有两个版本：FIP和WORLD FIP。上的DIP开关用于Remo扫描仪将使用的版本。同样的方法将用于两个公共汽车驾驶室。上的DIP开关必须设置远程扫描仪的FIP位置。说明FIP Remo扫描仪是一种标准，可轻松插入.FIP总线接口安装和硬件八月Q的背板。的前端具有以下引脚：两个FIP总线驾驶室的引脚D。可以在不影响总线连续性的情况下断开总线与的连接。第二总线是第一总线的备份；它的用途是optiol。
the bus via FIP Remo Scanner s. Ea remo drop can include one or slot in rack one or slot expansion rack and any mix of discre and alog s. „ Generic Devices su as generalpurpose purs that are inrfaced the bus via a FIP Inrface . Q apr Option s The FIP Bus Controlr is a standard rackmound . It plugs easily in the ’s backplane. The lat on the botm of the secures it in position. Pin FIP Fieldbus Pin FIP Fieldbus Pin Serial RS OK Run Carrier Dect . Transmit Eb . Carrier Dect . Transmit Eb . Figure . FIP Bus Controlr There are DIP swis or jumpers set on the . The FIP Bus Controlr has six status Ds an RS serial port and two identical FIP bus s. Status Ds The Ds on the front of the FIP Bus Controlr display status and activity. Serial Port The pin serial port is used connect a pur for upgrading the operating firmware of the Bus Controlr and for configuring by an exrl configuration ol. FIP Bus s The two pin s on the FIP Bus Controlr provide for attament of one or two FIP busses. The two busses provide a redundant bus capability. Installation and Hardware August Q ICBEM FIP Remo Scanner The FIP Facry Instrumentation Procol Remo Scanner catalog number ICBEM is an inlligent that inrfaces s a FIP bus. Up s can be acmodad by using two slot s connecd by an expansion cab. gether the Remo Scanner and the s it serves are referred as an Nest. The FIP Nest can include most s. The host CPU can be any type of CPU capab of municating on a FIP bus. A in the host su as a FIP Bus Controlr provides the necessary inrface between the FIP bus and the host CPU. FIP Bus Controlr CPU FIP Bus Host CPU Up devices Nest Handheld Programmer Expansion Cab up feet Mers Scanner Figure . Examp of FIP Remo Scanner Sysm Configuration The HandHeld Programmer provides a convenient way perform setup moniring and control functions. Features of the Remo Scanner The FIP Remo Scanner performs the following basic functions: „ controls operation of the nest in the secd mode „ scans discre and alog s and intains scan timing „ ps data FIP application riabs „ dects and sysm faults and reports them the FIP network „ permits standalone configuration using HandHeld Programmer „ retains its network configuration through loss of power Q apr Option s „ permits forcing from the HandHeld Programmer „ dects and records input transitions „ supports FIP messaging services „ responds an exrl synronization sigl „ can provide blinking or pulsed s „ can provide input filring and atr dection FIP Bus Inrface The Remo Scanner municas at a data ra of MHz. There are two versions of the FIP standard: FIP and WORLD FIP. A DIP swit on the is used sect the version that will be used by the Remo Scanner. The same method will then be used on both bus cabs. The DIP swit on the must be set the FIP position for the Remo Scanner munica with a . Description The FIP Remo Scanner is a standard that plugs easily in the backplane of the . FIP Bus Inrface Installation and Hardware August Q s The front of the has the following s: pin D s for two FIP bus cabs. A bus can be disconnecd from the without disturbing the continuity of the bus. The second bus is a backup for the first bus; its use is optiol.
