IS215UCVEM10A工控备件机器人模块
电源功率输入在电源的功率限制内。警告：如果使用同一直流输入电源，请在Sysm中提供两个或多个电源，确保每个机架p+和第二个机架的连接极性相同。不要跨越正负线。由此导致的脑桥差异可能会伤害人员或导致设备损坏。此外，还必须连接本4月早些时候所述的系统接地。安装和硬件8月Q基本安装程序编号：必须安装在一个保护外壳中。外壳应能够适当地消散其内部所有设备堆产生的热量。有关计算散热的详细信息，请参阅附录F。在开始安装程序之前，应编制包括布局和布线图在内的系统设计。本节提供了安装系统的基本spbysp方法。一些sps参考了本apr的早期章节以了解更多详细信息。一个气氛是按照一个将使过程尽可能高效的顺序来放置sps。但是，由于sysm设计的差异很大，因此此顺序可能不是最有效的，因此您可以根据需要修改此过程。收集作业的集合布局、打印和其他信息。警告：避免触电人员或损坏您的设备。我们提醒您，在安装和接线之前，请关闭系统的所有电源。此外，钻孔和攻丝时，应将所有电子部件远离该区域，以免金属碎片和锉屑进入这些敏感部件。从布局图中可以看出，s将在哪里堆积。使用布局图上给出的尺寸或从本页开始布置位置。标记安全接地的ho位置，参见本四月的安全接地。标记屏蔽接地连接的ho位置（如果有）。有关说明，请参阅本手册中的屏蔽接地和公司部分。完成系统其余部分的位置铺设。这包括您将使用的任何块。某些点的DINrail土墩由Weidmullr制造。DINrail丘GE块快速连接TBQC组件可用于某些点和点离散件。如果使用这些TBQC，请参考附录H获取数据。APM和DSM也使用DINrail土墩。不，我们记得在安装任何部件之前对所有部件进行钻孔和攻丝。这将避免在部件中获得ips和文件。钻孔并轻敲标记的hos。用于安装或mm尺寸。安装s。使用质量良好的x英寸或x毫米大小的螺钉。我们记得在螺钉头下使用星形锁紧垫圈和平垫圈。星形锁紧垫片应位于螺钉头和平垫圈之间，以确保接地紧密，并防止螺钉松动。按照本四月的“安全接地”部分所示连接每个接地。如果您有扩展或Remo机架，请为每个机架确定正确的机架编号，然后在安装前使用机架编号部分双列直插式封装DIP开关设置机架编号。有关设置这些DIP开关的详细信息，请参阅参考。机架编号应由sysm编程器分配，因为它们对应于sysm配置设置和程序内存寻址。
supply power input s within power limitations of the supply. Warning If the same DC input power source is used provide power two or more power supplies in a Sysm ensure that connection polarity is identical at ea rack p + and second . Do not cross the Positive + and Negative lines. A resulting difference in pontial can injure personnel or cause dage equipment. Also ea must be connecd a mon sysm ground described earlier in this apr. Installation and Hardware August Q Basic Installation Procedure No: s must be mound in a proctive enclosure. The enclosure should be capab of properly dissipating the heat produced by all of the devices mound inside it. For details on calculating heat dissipation refer Appendix F. The sysm design whi includes producing the layout and wiring drawings should be pd before beginning the installation procedure. This section offers a basic spbysp approa installing a sysm. Some sps refer earlier sections of this apr for additional details. An atmpt was de place the sps in an order that will ke the process as efficient as possib. However due the wide variance in sysm designs this order y not be the most efficient for your sysm so you y wish modify this procedure fit your needs. . Gather the setics layouts prints and other infortion for the job. Warning avoid the possibility of ectrical shock personnel or dage your we remend that you shut off all power the sysm before mounting and wiring the . Also keep all ectronic ponents away from the area whi drilling and tapping keep metal ips and filings out of these sensitive ponents. . From the layout drawing dermine where the s will be mound. Lay out the ho locations either using the dimensions given on your layout drawing or from the s apr of this . . rk the ho locations for the safety ground see Safety Ground in this apr. . rk the ho locations for shield ground connections if any. See Shield Ground and acpanying sections in this apr for instructions. . Finish laying rking ho locations out the rest of the sysm. This includes any blocks you will be using. DINrail mound blocks for some of the point s are nufactured by Weidmulr. DINrail mound GE Block Quick Connect TBQC assemblies are optional for some of the point and point discre s. If using these TBQCs refer Appendix H for data. Also APM and DSM s use DINrail mound blocks. No We remend drilling and tapping all hos before mounting any ponents. This will avoid getting ips and filings in the ponents. . Drill and tap the rked hos. For mounting use or mm size. . Mount the s. Use good quality x in or x mm size screws. We remend using star lock washers and flat washers under the screw heads star lock washer should be locad between screw head and flat washer ensure a tight ground connection and keep the screws from loosening. Connect ea ground as shown in the Safety Ground section of this apr. . If you have Expansion or Remo racks dermine the correct rack number for ea one then set the rack numbers using the Rack Number Section dual inline package DIP swit on Q apr Installation the . Pase refer the s apr for details on setting these DIP swis. Rack numbers should be assigned by the sysm programmer because they correspond sysm configuration settings and program memory addressing.
