IS215UCVFH2AB机器人模块卡件
在两个TBQC块上的面板和面板之间。不需要右侧和左侧驾驶室。驾驶室列表见附录H。设备块。有关引脚信息，请参阅规范。块快速连接TBQC组件是某些离散件的选项。更多信息请参见附录H。使用Generic BlockStrip Mount BlockStrip，机柜面板。将ICCBL驾驶室或驾驶室的面板和驾驶室的剥离端连接到挡块上。不需要右侧和左侧驾驶室。驾驶室列表见附录H。驾驶室数据表见apr。设备阻止条。有关引脚信息，请参阅规范。Q apr安装直接方法将ICCBL驾驶室或驾驶室的面板和驾驶室的剥离端直接连接到现场设备。驾驶室数据见apr。有关引脚信息，请参阅规范。对于模拟输入或信号连接，模拟双绞线屏蔽仪表室的一般布线方法应严格遵守。屏蔽的正确接地也很重要。为了抑制电气噪声，驾驶室屏蔽只能在驾驶室的一端接地。对于输入端，接地端位于噪声最大的环境中，而非现场设备端。在结尾处为s接地。更多屏蔽接地信息，请参见规范。模拟输入接线方法纠正电噪声问题有时可能是三端双向纠错程序。然而，一般来说，最好将驾驶室护罩接地，使其尽可能靠近噪声源，而通常在设备端。在槽形噪声问题中，屏蔽接地点的位置有时是有益的实验。请记住，驾驶室护罩只能在一端接地。此外，最好尽可能缩短裸露的驾驶室广告的长度，以尽量减少暴露在噪声环境中的非屏蔽导线的长度。有关更多详细信息，请参阅规范。使用通用块或条带在控制机柜内安装一个条带，并从板上的条带输入端运行一个屏蔽的驾驶室。将每个驾驶室的屏蔽连接到条带旁边的金属面板。不要用收缩管连接端部的屏蔽，在驾驶室和绝缘层端部切断屏蔽。现场设备-带屏蔽驾驶室的带接地设备端的屏蔽层仅切断驾驶室带端的屏蔽和带收缩管的绝缘层。还应尽可能缩短条带和设备端屏蔽广告的外露长度。直接方法从现场设备传感器桥体等直接运行屏蔽驾驶室。将导线连接到电路板上的适用螺钉。安装和硬件八月Q现场设备端的屏蔽接地，暴露出噪声环境中的最小导电量。不要用收缩管连接端部的屏蔽，在驾驶室和绝缘层端部切断屏蔽。由于驾驶室屏蔽要求，模块快速连接TBQC组件不适合与模拟设备一起使用。模拟接线通用Ea应采用优质屏蔽连接，驾驶室屏蔽端接地。有关详细信息，请参阅规范。使用通用块或条带在控制机柜内安装条带，并从板上的条带运行屏蔽驾驶室。
between the ’s facepla and the s on the two TBQC blocks. No that both a right side and ft side cab is required. See Appendix H for a list of cabs. devices the blocks. See the Specifications for pinout infortion. The Block Quick Connect TBQC Assembly is an option for certain discre s. See Appendix H for more infortion. With a Generic BlockStrip Mount blockstrip the enclosure panel. Connect an ICCBL cabs or a cusm de cabs the ’s facepla s and the stripped ends of the cabs the blockstrip. No that both a right side and ft side cab is required. See Appendix H for a list of cabs. See apr for cab data sheets. devices the blockstrip. See the Specifications for pinout infortion. Q apr Installation Direct Method Connect an ICCBL cab or a cusm de cab the ’s facepla s and the stripped ends of the cab directly the field devices. See apr for cab data. See the Specifications for pinout infortion. General Wiring Methods for Analog s Twisd shielded instrumentation cab is strongly remended for analog input or signal connections. Proper grounding of the shield is also important. For ectrical noise suppression the cab shield should only be grounded at one end of the cab. For Input s ground the end that is in the noisiest environment whi ofn is at the field device end. For s ground at the end. See Specifications for more shield grounding infortion. Analog Input Wiring Methods Correcting ectrical noise probms can sometimes be a trialanderror routine. However in general it is generally best ground the cab shield as close the source of the noise as possib whi is usually at the device end. In troubshooting noise probms sometimes it is beneficial experiment with the shield grounding point location. Remember the cab shield should be grounded at one end only. Also it is best keep the ngth of stripped cab ads as short as possib minimize the ngth of unshielded conducrs that will be exposed the noisy environment. See the Specifications for additional details. Using a Generic Block or Strip Mount a strip inside the control enclosure and run a shielded cab from the strip ea input on the ’s board s. Connect ea cab’s shield the metal panel next the strip. Do not connect the shields at the end cut shield off at end of cab and insula with shrink tubing. the field device the strip with a shielded cab grounding the shield at the device end only cut shield off at strip end of cab and insula with shrink tubing. Also keep the ngth of exposed outside of shield ads at the strip and device ends as short as possib. Direct Method Run a shielded cab from the field device transducer pontiomer etc. directly the . Connect the conducrs the applicab screws on the ’s board. Installation and Hardware August Q Ground the shield at the field device end exposing a minimum amount of conducr the noisy environment. Do not connect the shield at the end cut shield off at end of cab and insula with shrink tubing. TBQC not Remended for Analog s The Block Quick Connect TBQC Assembly is not remended for use with analog s due cab shielding requirements. Analog Wiring General Ea should be connecd using a good quality shielded with the cab shield grounded at the end. See Specifications for more infortion. Using a Generic Block or Strip Mount a strip inside the control enclosure and run a shielded cab from the strip ea on the ’s board s.
