IS215VCMIH2BE IS200VCMIH2BEE工控备件模块
安装主板安装和硬件八月Q卸下主板卸下主板：打开塑料板盖。向上推顶轴，以润滑缸体。千斤顶抓住拉片并将其向上拉，直到触点与外壳分离，底部枢轴钩脱离。拉出一个制表符图形。卸下a板Q apr安装板柱该板在ft侧有三个柱。p柱和botm柱将板盖固定到位。中柱将电路板接线固定到位。如果您不需要它，请将接线保持在适当位置，中间接线柱可以很容易地折断。如果需要，请小心不要不小心将其折断。请将接线固定在适当位置。安装和卸下带有固定螺钉的板，如下图所示，Discre的ICMDLF和lar和ICMDLF以及lar具有一个配有固定螺钉的特殊板。这些螺钉可防止电路板连接在遭受严重振动的应用中断裂ICMDLF A A Removeab板铰链盖固定螺钉固定螺钉目录号图。卸下固定螺钉的电路板：卸下这些电路板，首先松开电路板前面的两个固定螺钉，然后按照“卸下电路板”一节中的标准拆卸说明进行操作。固定螺钉固定在电路板中，不需要拆下。安装：按照“安装电路板”一节中的标准安装说明安装这些电路板，然后拧紧两个固定螺钉，将其固定在Newnmer of rque周围。安装和硬件八月Q安装警告请务必遵循本节中的接地说明。如果接地不当，可能会导致设备操作不当和人员受伤。安装面板使用四个高质量x x mm细螺钉锁紧垫圈和平垫圈。将螺钉安装在四个螺纹位置。s apr具有适用的尺寸和安装克拉。通过使用适当的适配器，所有插槽都可以在标准机架中堆积。这一点也在本节中讨论。为了散热，首选垂直安装方向。其他安装方向将需要降低电源电流能力。有关详细信息，请参阅apr系统设计。所有s必须接地。本节的安全接地部分有详细信息。必须在ea Expansion或Remo上设置机架编号部分开关。CPU不需要这种速度。机架编号应由系统设计师指定。如果未正确设置机架编号部分开关，将导致系统功能失效。有关设置这些swi的详细信息，请参阅s apr。安装机架两个可选的Adapr支架允许在机架内安装插槽。Ea安装只需要一个adapr支架。ICACC前安装Adapr支架。用于安装在机架正面。通过将adapr支架顶部和底部的卡舌插入塑料盖顶部和底部相应的槽中，安装adapr支架。否：虽然图中显示塑料盖已拆下，但这仅用于说明。无需拆下盖或安装支架。在支架就位的情况下，插入并拧紧支架中的两个螺钉，使其穿过支架中的螺纹螺钉的背面。Q apr安装
Installing the motherboard Installing and hardware August Q Removing the motherboard Removing the motherboard: Open the plastic cover. Push the jacking shaft upward in order to lubricate the cylinder block. The jack grabs the tab and pulls it up until the contact disengages from the housing and the bottom pivot hook disengages. Pull out a tab graphic. Remove the a board Q apr mounting plate post. The board has three posts on the ft side. The p column and the botm column fix the plate cover in place. The middle post fixes the circuit board wiring in place. If you do not need it, please keep the wiring in place, and the middle terminal can be easily broken. If necessary, be careful not to break it accidentally. Please fix the wiring in an appropriate position. Install and remove the board with fixing screws, as shown in the figure below. The ICMDLF and lar of Discrete and the ICMDLF and lar have a special board with fixing screws. These screws prevent the circuit board connection from breaking the ICMDLF A A Removeab board hinge cover fixing screws in applications subject to severe vibration. Remove the circuit boards with fixing screws: To remove these circuit boards, first loosen the two fixing screws on the front of the circuit board, and then follow the standard removal instructions in the section "Removing the circuit board". The fixing screws are fixed in the circuit board and do not need to be removed. Installation: Install these circuit boards according to the standard installation instructions in the section "Installing circuit boards", and then tighten the two fixing screws to fix them around Newnmer of rque. Installation and Hardware August Q Installation Warning Be sure to follow the grounding instructions in this section. Improper grounding may lead to improper operation of equipment and personal injury. The mounting panel uses four high quality x x mm fine screw lock washers and flat washers. Install the screws at four threaded locations. S apr is available in suitable sizes and mounting carats. All slots can be stacked in a standard rack by using the appropriate adapters. This is also discussed in this section. For heat dissipation, the vertical installation direction is preferred. Other mounting directions will require reduced power current capability. For more information, see apr system design. All s must be grounded. The safety grounding section of this section has detailed information. The rack number section switch must be set on ea Expansion or Remo. The CPU does not need this speed. The rack number shall be specified by the system designer. If the switch of rack number part is not set correctly, the system function will fail. For details on setting up these swis, see s apr. Installing the Rack Two optional Adaptr brackets allow slots to be installed in the rack. Ea installation only requires one adapr bracket. Install the Adaptr bracket before ICACC. Used for mounting on the front of the rack. Install the adapr bracket by inserting the tabs on the top and bottom of the adapr bracket into the corresponding slots on the top and bottom of the plastic cover. No: Although the figure shows that the plastic cover has been removed, this is only for illustration. It is not necessary to remove the cover or the mounting bracket. With the bracket in place, insert and tighten the two screws in the bracket through the back of the threaded screws in the bracket. Q apr installation
