IS220PPDAH1A/IO工控备件机器人模块
大气压力860…1060毫巴沉降时间<4 ms湿度45…75%r.h。中温开关开启时间<15 ms安装位置根据需要精度数据电源24V DC存储温度-40…+70°C（-40…+158°F）mBar型号：不可重复性测量范围≤0.1 bar≤0.2%量程≤0.1%量程mBar型号测量范围≤0.1bar：≤0.2%量程≤0.1 bar：≤0.1%量程真空电阻10毫巴（0.145 psi）信号噪声≤±0.3%量程湿度45…75%r.h.速率温度范围内0…80°C（32…176°F）时的温度误差典型：量程的1.0%最大值：量程的2.5%使用寿命1000万负载循环耐冲击性500 g（17.64 oz）（IEC 60068-2-27，机械）长期漂移≤量程短路电阻模拟+vs。模拟-测量范围≤0.1巴：≤±-0.5%量程≤0.4巴：≤≤-0.2%量程>0.4巴：≤？-0.1%量程反极性保护模拟+vs。模拟-非线性≤量程的±0.5%抗振性10 g（0.35 oz）（IEC 60068-2-6，谐振下）入口保护（根据IEC60529）IP67–M12x1 4针出版物836P-IN002B-EN-P-2017年12月3非显示固态压力变送器尺寸[mm（in.）]1/4 in.NPT内螺纹1/4 in。NPT外螺纹工艺连接调试制造机械连接•安装时，确保仪表和测量点的密封面清洁无损坏。•只能使用合适的工具通过扳手平面将仪器拧入或拧下至规定的扭矩。正确的扭矩取决于工艺连接和所用垫圈的尺寸（形状/材料）。拧紧或拧下压力变送器时，不要将外壳用作接触面。•小心不要穿线。•最大扭矩为50 N·m（442.54 lb·in）。配套电缆过程连接889D-F4AC-2（M12x1连接器）测量单元压阻测量单元和金属测量隔膜889D-R4AC-2（M22x1直角连接器）应用测量和监控绝对压力和表压过程连接螺纹−1/4 NPT内螺纹−1/4 NPS外螺纹−G1/4 BSPP外螺纹G 1/2B SAE 7/16-20 UNF O形圈凸台注意：之前试运行时，必须对压力变送器进行目视检查液体泄漏表明损坏。•只有在安全状况良好的情况下才能使用压力变送器。和罗克韦尔软件是股份有限公司的商标。商标不属于其各自公司的财产。罗克韦尔Otomasyon Ticaret A.å.，Kar Plaza伊什默克齐E Blok Kat:6 34752伊泽伦克，伊斯坦布尔，电话：+90（216）5698400在其网站上保持最新的产品环境信息，网址为about us/可持续性道德/产品环境合规性.page。
Atmospheric pressure 860…1060 mbar Settling time < 4 ms Humidity 45…75% r. h. Medium temperature Switch on time < 15 ms Mounting position As required Accuracy Data Power supply 24V DC Storage temperature -40…+70 °C (-40…+158 °F) mBar models: nonrepeatability measuring range ≤ 0.1 bar ≤ 0.2% span ≤ 0.1% of span mBar models range of measure ≤ 0.1 bar: ≤ 0.2% of span ≤ 0.1 bar: ≤ 0.1% of span Vacuum resistance 10 mbarabs (0.145 psi) Signal noise ≤ ± 0.3% of span Humidity 45…75 % r. h. Temperature error at 0…80 °C (32…176 °F) in rate temperature range Typical: 1.0% of span Maximum: 2.5% of span Service life 10 million load cycles Shock resistance 500 g (17.64 oz) (IEC 60068-2-27, mechanical) Long-term drift ≤ ± 0.1% of span Short circuit resistance Analog + vs. Analog - Range of measure ≤ 0.1 bar: ≤ ± -0.5% of span ≤ 0.4 bar: ≤ ± -0.2% of span > 0.4 bar: ≤ ± -0.1% of span Reverse polarity protection Analog + vs. Analog - Non-linearity ≤ ± 0.5% of span Vibration resistance 10 g (0.35 oz) (IEC 60068-2-6, under resonance) Ingress protection (per IEC60529) IP67 – M12x1 4 pin Publication 836P-IN002B-EN-P - December 2017 3 Non-display Solid-state Pressure Transmitter Dimensions [mm (in.)] 1/4 in. NPT Female 1/4 in. NPT Male Process Connection Commissioning Making the Mechanical Connection • While mounting, make sure that the sealing faces at the instrument and the measuring point are clean and undamaged. • Only screw or unscrew the instrument via the spanner flats and to the prescribed torque with an appropriate tool. The correct torque depends on the dimensions of the process connection and the gasket used (form/material). When screwing or unscrewing the pressure transmitter, do not use the housing as contact surface. • Be careful not to cross-thread. • Max torque is 50 N·m (442.54 lb·in). Mating Cables Process Connection 889D-F4AC-2 (M12x1 connector) Measuring Cell Piezoresistive measuring cell and metallic measuring diaphragm 889D-R4AC-2 (M12x1 right angle connector) Application Measurement and monitoring of absolute and gauge pressures Process connection Thread − 1/4 NPT female − 1/4 NPT male − G1/4 BSPP male G 1/2B SAE 7/16-20 UNF O-ring BOSS ATTENTION: Before commissioning, the pressure transmitter must be subjected to a visual inspection. • Fluid leakage is indicative of damage. • Only use the pressure transmitter if it is in perfect condition concerning safety. and Rockwell Software are trademarks of , Inc. Trademarks not belonging to are property of their respective companies. Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400 maintains current product environmental information on its website at about-us/sustainability-ethics/product-environmental-compliance.page.
