IS220PPRFH1A 336A4940CSP20工控自动化卡件
和罗克韦尔软件是股份有限公司的商标。商标不属于其各自公司的财产。罗克韦尔Otomasyon Ticaret A.å.，Kar Plaza伊什默凯兹E Blok Kat:6 34752伊泽伦克，伊斯坦布尔，电话：+90（216）5 美国印刷安装说明1。用3/32 in.六角套筒扳手松开夹紧环上的螺钉。2.将编码器滑动到配合轴上，直到系绳安装件或防转销靠在机器表面上。编码器应在轴上自由滑动；如果没有，不要强行。检查轴有无干涉，如凿痕、毛刺、锈蚀或尺寸。如果已经存在安装孔或防转销挡块，则继续执行步骤6。3.标记安装孔和/或防转销止动位置。4.滑下编码器。钻孔并轻敲标记孔，以接受0.375 in.x 16（系绳选项B或C）或0.5 in.x 13（系绳选择A）螺栓。5.将编码器滑回轴中，直到系绳安装件或防转销靠在机器表面上。6.用0.375英寸或0.5英寸螺栓连接编码器。7.将夹紧环拧紧至8英寸磅。8.根据“电气连接”下的表格进行电气连接。施加规定电压（参见本出版物第1页“选择”下的表“e”）。重要事项确保配合轴倒角且无油脂。重要事项拧紧螺栓时，不要对系绳支架施加压力。重要事项接线必须符合国家电气规范和适用的地方规范和条例。支持使用以下资源访问支持信息。文档反馈您的意见将帮助我们更好地满足您的文档需求。如果您对如何改进本文档有任何建议， 查找相关固件的帮助。
And Rockwell Software are trademarks of Co., Ltd. Trademarks are not the property of their respective companies. Rockwell Otomasyon Ticaret A. ✪., Kar Plaza Ishmerkaz E Blok Kat: 6 34752 Isserlenk, Istanbul, Tel:+90 (216) 5 US Printed Installation Instructions 1. Loosen the screws on the clamping ring with a 3/32 inch hex socket wrench. 2. Slide the encoder onto the mating shaft until the tether mount or anti rotation pin rests against the machine surface. The encoder shall slide freely on the shaft; If not, don't force it. Check the shaft for interference, such as gouges, burrs, rust, or dimensions. If the mounting hole or the anti rotation pin stop already exists, proceed to step 6. 3. Mark the mounting hole and/or the stop position of the anti rotation pin. 4. Slide down the encoder. Drill and tap the marked holes to accept 0.375 in. x 16 (lanyard option B or C) or 0.5 in. x 13 (lanyard option A) bolts. 5. Slide the encoder back into the shaft until the tether mount or anti rotation pin rests against the machine surface. 6. Connect the encoder with 0.375 inch or 0.5 inch bolts. 7. Tighten the clamping ring to 8 inch pounds. 8. Make electrical connections according to the table under "Electrical connections". Apply the specified voltage (see Table "e" under "Selection" on page 1 of this publication). It is important to ensure that the mating shaft is chamfered and free of grease. IMPORTANT Do not apply pressure to the tether bracket when tightening the bolts. Important wiring must comply with national electrical codes and applicable local codes and regulations. Support uses the following resources to access support information. Document feedback will help us better meet your document needs. If you have any suggestions on how to improve this document, look for help with the relevant firmware.
