MVME162-021A工控备件机器人模块
最大速度磅轴向负载力径向负载力施加在轴延伸中心。系列或更小框架尺寸的低惯量无刷伺服电机自动化年月轴向负载力额定值最大径向负载电机类别。编号，最大速度电机类别。转分转分转分转分，最大速度磅系列或更小框架尺寸的低惯量无刷伺服电机自动化年月连接器数据本表提供了连接器上的反馈电源和制动引脚的信号描述。反馈和引脚描述引脚高分辨率编码器高分辨率编码器增量编码器引脚和相功率相位和功率相位也可以分别标记为和。相相接地数据数据保留数据数据保留保留保留保留公共公共连接器保留保留公共保留保留反馈连接器系列或更小框架尺寸的低惯量无刷伺服电机自动化年月拆除和安装轴键轴键由钢制成。指定的公差为安全和刚性连接提供过盈配合略大于开口。要取下轴键，请执行以下操作之一用钳子或类似工具抓住键，将其抬起。将螺丝刀插入钥匙和插槽之间，撬起钥匙。要安装轴键，请执行以下步骤。在继续操作之前，确认替换键与轴中的键槽和匹配的机械连接例如，联轴器或滑轮相匹配。将键的前部与电机轴的前部对齐。这可防止键槽电机端的弧形切割端干扰键的正确定位。用夹具支撑轴直径的下侧，并使用受控的按压装置在顶面施加恒定的力，将键压入轴中。轴键安装注意事项安装或拆卸轴键时，不要用工具敲击电机的轴联轴器或滑轮。如果在安装联轴器和皮带轮或拆除轴键时对轴施加剧烈冲击，或者如果从电机电机上施加杠杆，则可能会损坏电机轴承和反馈装置以拆除安装在电机轴上的装置。用车轮拉拔器向轴的用户端施加恒定压力，以移除摩擦配合或卡住的装置。用于电机支架的键槽键轴支架的键对齐径向切口系列低惯量无刷伺服电机，框架尺寸为或更小自动化年月电机电缆和附件套件本节介绍了系列低惯性电机可用的附件。电机电缆工厂制造的反馈电缆和电力电缆有标准电缆长度。
Maximum speed pounds axial load force Radial load force is applied to the shaft extension center. Series or smaller frame size low inertia brushless servo motor automation Monthly axial load force rating Maximum radial load motor category. Number, maximum speed motor category. Turn to turn, turn to turn, turn to turn, maximum speed pounds series or smaller frame size low inertia brushless servo motor automation monthly connector data This table provides the signal description of the feedback power supply and brake pin on the connector. Feedback and pin description pins High resolution encoder High resolution encoder Incremental encoder pin and phase power phase and power phase can also be marked as and respectively. Phase grounding data data retention data retention retention retention retention public public connector retention retention public retention retention feedback connector series or smaller frame size low inertia brushless servo motor automation removal and installation shaft key shaft key is made of steel. The specified tolerance provides an interference fit slightly greater than the opening for safe and rigid connections. To remove the shaft key, do one of the following to grasp the key with pliers or a similar tool and lift it. Insert a screwdriver between the key and the slot and pry up the key. To install the shaft key, perform the following steps. Before continuing, confirm that the replacement key matches the keyway in the shaft and the matching mechanical connection, such as coupling or pulley. Align the front of the key with the front of the motor shaft. This prevents the arc-shaped cutting end of the motor end of the keyway from interfering with the correct positioning of the key. Use a jig to support the lower side of the shaft diameter, and use a controlled press device to apply a constant force on the top surface to press the key into the shaft. Precautions for shaft key installation When installing or removing the shaft key, do not use tools to knock the shaft coupling or pulley of the motor. If the shaft is severely impacted when installing the coupling and pulley or removing the shaft key, or if the lever is applied from the motor, the motor bearing and feedback device may be damaged to remove the device installed on the motor shaft. Use a wheel puller to apply constant pressure to the user end of the shaft to remove friction fits or stuck devices. Keyway for motor support Keyway for key shaft support Key alignment Radial notch series low inertia brushless servo motor, frame size is or smaller Automation motor cable and accessory kit This section describes the accessories available for series low inertia motors. The feedback cable and power cable manufactured by the motor cable factory have standard cable lengths.
