MVME162-411机器人备件
如果正确的模块可用消耗量红色脉动状态指示器，则真正的警报只是激活正确的静态或继电器输出。根据配置的比率和比率，状态指示器闪烁以指示消耗的量，如图所示例如，如果配置的比例为，比率为，则*，在该示例中，状态指示器每闪烁一次。此功能适用于所有装置，不需要数字脉冲输出。根据，最大频率。底座上的后位置状态指示灯绿色，作为通电通信模块两个状态指示灯一个用于绿色，一个用于琥珀色闪烁绿色和琥珀色指示正确的通信接线打开单元绿色状态指示灯关闭，琥珀色状态指示灯打开可指示接线不当和的接线颠倒键盘用于仪表工作参数总能量的可变选择编程，和部分能量重置表显示状态指示器和命令续属性值条件消耗表主要功能属性值密码最多四位数的数字代码编程数据的两个保护级别一级密码，无保护二级密码从，所有数据都受保护系统选择系统。不平衡负载相线形系统不平衡负载三相线三角形三电流和三线对线电压测量对于连接，两电流在螺纹端子上有特殊接线和三线电压测量。系统。个平衡负载相线，一个电流和三个线对线测量。三相线单电流和三线对中性点电压测量。系统。个平衡负载相线，一个电流和一个线对中性点电压测量系统相线分相系统相线单相变压器比如果具有二次电流，则高达年月附录技术规范滤波器工作范围可从输入显示比例滤波系数可从滤波动作测量模拟信号重传串行通信基本变量及其派生变量显示变量数量每页最多五个变量。请参阅第页的前面板功能。根据所选应用程序，可提供七组不同的变量。请参阅第页背光的显示功能背光时间可从始终打开编程到分钟虚拟报警工作状态基本单元仅指示或带有可选数字输出模块报警数量最多个工作模式向上报警和向下报警受控变量报警可连接到任何瞬时变量。
If the correct module has a red pulsation status indicator for available consumption, the true alarm is simply to activate the correct static or relay output. According to the configured ratio and ratio, the status indicator flashes to indicate the amount consumed, as shown in the figure. For example, if the configured ratio is, the ratio is, then *, in this example, the status indicator flashes every time. This function is applicable to all devices and does not require digital pulse output. According to, the maximum frequency. The rear position status indicator on the base is green. As two status indicators of the power on communication module, one is for green, the other is for amber flashing green and amber indicating correct communication wiring. The green status indicator of the unit is off, and the amber status indicator is on. It can indicate improper wiring and wiring reversal. The keyboard is used for variable selection programming of the total energy of the instrument working parameters, And some energy reset tables display status indicators and command continuation attribute value condition consumption tables. The main function attribute value password can be up to four digits. The number code programming data has two protection levels, the first level password, and the unprotected second level password. All data are selected by the protection system. Unbalanced load phase linear system Unbalanced load three-phase line triangle three current and three wire to wire voltage measurement For connection, the two currents have special wiring and three wire voltage measurement on the screw terminals. System. A balanced load phase line, a current and three line to line measurements. Three phase line single current and three wire to neutral point voltage measurement. System. A balanced load phase line, a current and a line to neutral point voltage measuring system Phase line Phase separation system Phase line Single phase transformer ratio If it has secondary current, it can be as high as the technical specifications in the appendix of the month The working range of the filter can be displayed from the input Proportional filter coefficient can be measured from the filtering action Analog signal retransmission Serial communication basic variables and their derived variables The number of displayed variables can be up to five variables per page. See Front panel features on page. Seven different sets of variables are available depending on the application selected. See page Display function of backlight Backlight time can be programmed from always on to minute Virtual alarm Working state Basic unit only indicates or has optional digital output module Alarm number Maximum working modes Up alarm and Down alarm Controlled variable alarm can be connected to any instantaneous variable.
