MVME162P-344工控自动化卡件
标签也可以在设备上或内部，以提供特定的预防措施。警告确定在危险环境中可能导致爆炸的做法或情况的信息，这可能导致人身伤害或财产损失或经济损失。在手动复位模式下，输出信号只能在移除驱动力并复位后恢复。手动复位通过按下和释放盖上安装的控制单元复位按钮或远程安装的按钮来实现。在通电或断电后以及随后恢复电源后，输出将“关闭”，直到收到复位信号，即使垫子未启动。在自动复位模式下，仅通过移除驱动力来实现输出信号。对于这两种模式，在启动垫子后，安全触点将始终处于断开状态。第节将更详细地介绍模式选择。各个传感器垫通过根电线相互连接并连接到控制单元。控制单元具有交叉监控的安全继电器，可以配置该单元，以便检测到外部接触器故障。控制单元电气故障符合第类的要求，机器控制系统的相关部分也能满足。垫子传感器符合第类的要求。第节详细介绍了接口。垫子的工作原理如图所示。图当垫子被激活时，不导电的可压缩隔板显示为黑色压缩到其凹槽中，允许两个板进行接触，从而提供全部灵敏度。该系统旨在检测体重为或以上的成年人。它适用于检测使用助行器手杖或框架的成年人。该系统不适合检测儿童。该系统不得与垫上的任何额外覆盖物一起使用。垫在静止的钢板上模制乙烯基垫激活。垫的乙烯基外表面完全密封，以防止液体进入。它能抵抗漂白酸盐和大多数工业化学品。未经自动化股份有限公司书面许可，严禁复制本手册的全部或部分内容。在本手册中，我们会在必要时使用注释，以提醒您注意安全事项。有关耐化学性的详细指南，请参阅第节。系统在下运行，故障电流受限。因此，在正常情况下，垫或互连线路的损坏不会产生任何电击危险。图基本系统和连接用两个接触器显示。和。注复位按钮的位置与上的位置不同。电源端子电源端子手动复位自动复位开关辅助保险丝主保险丝选择开关盖安装复位按钮控制单元编号+指示器远程复位端子远程复位指示端子接触器监控端子辅助端子安全输出端子垫连接端子机器启用绿色自动复位模式绿色手动复位模式绿色电源绿色传感器垫接触器控制电源无电压辅助。
Labels can also be on or inside the equipment to provide specific precautions. Warning Information that identifies practices or situations that could lead to an explosion in a hazardous environment, which could result in personal injury or property damage or economic loss. In the manual reset mode, the output signal can only be restored after the driving force is removed and reset. Manual reset is achieved by pressing and releasing the control unit reset button installed on the cover or the remote installed button. After power on or power off and subsequent power restoration, the output will "turn off" until a reset signal is received, even if the mat is not started. In the automatic reset mode, the output signal is achieved only by removing the driving force. For both modes, the safety contact will always be disconnected after starting the mat. Section describes mode selection in more detail. The sensor pads are connected to each other and to the control unit via a wire. The control unit has a cross monitored safety relay, which can be configured to detect external contactor faults. The electrical failure of the control unit meets the requirements of Category, and the relevant parts of the machine control system can also meet the requirements. The cushion sensor meets the requirements of category. Section describes the interface in detail. The working principle of the mat is shown in the figure. Figure When the mat is activated, the non-conductive compressible partition is shown as black compressed into its groove, allowing two plates to contact, thus providing full sensitivity. The system is designed to detect adults weighing or above. It is suitable for detecting adults using walking aid canes or frames. The system is not suitable for detecting children. The system shall not be used with any additional covering on the mat. The pad is activated by a molded vinyl pad on a stationary steel plate. The vinyl outer surface of the gasket is completely sealed to prevent liquid ingress. It is resistant to bleaches and most industrial chemicals. Without the written permission of Automation Co., Ltd., it is strictly forbidden to copy all or part of this manual. In this manual, we will use notes when necessary to remind you of safety precautions. Refer to Section for detailed guidance on chemical resistance. The system operates under and the fault current is limited. Therefore, under normal conditions, damage to the mat or interconnecting circuit does not create any electrical shock hazard. Figure Basic system and connections are shown with two contactors. And. Note The position of the reset button is different from that on the. Power terminal Power terminal Manual reset Automatic reset switch Auxiliary fuse Main fuse Selection switch Cover installation Reset button Control unit number+Indicator remote reset terminal Remote reset indication terminal Contactor monitoring terminal Auxiliary terminal Safety output terminal pad Connection terminal Machine enable green Automatic reset mode Green power Green sensor pad Contactor control power supply No voltage assistance.
