MVME162P-344E工控备件机器人模块
安装后，本手册涵盖了系统所有部件的安装和使用，包括特殊形状和尺寸的传感器垫。所有安装程序应由经过适当培训的合格人员执行，并应符合法定安全要求。安装前请完整阅读本手册。安装后，应将本手册保存在安全且可接近的地方。如需进一步帮助，请联系供应商。第节储存和搬运储存控制装置和垫传感器应储存在至+的温度范围内。垫子传感器应垂直存放。搬运和运输控制装置和垫传感器应在至+的温度范围内运输。如有必要，原始包装或类似包装应与加固一起使用，以防止损坏和弯曲。始终小心打开包装，避免被刀具等损坏。当传感器垫移动到位时，切勿通过其连接线拉动或提起传感器。对于较大的传感器垫，需要两个人来安全提升，并防止过度弯曲损坏传感器垫的风险。第节系统描述系统包括一个或多个互连的压敏垫和一个控制单元。检测区域内没有“死区”。单个传感器垫部分有矩形标准尺寸，也有特殊切割形状，最大尺寸为最大标准垫。所有传感器垫具有相同的结构和操作原理。每个垫子都有两块导电板由不导电的可压缩隔板隔开。这些垫子在下工作，并串联在一起，以形成机器周围危险区域的地面感应系统。通过垫子的电路由控制单元监控，当区域空闲时，控制单元向机器控制电路提供信注意确定可能导致人身伤害财产损失或经济损失的行为或情况的信息。注意事项有助于您识别危险，避免危险并认识到后果。重要信息确定对成功应用和理解产品至关重要的信息。电击危险标签可能位于设备上或设备内部，例如驱动器或电机，以提醒人们可能存在电压。对于个接触器，请参见压敏安全垫系统安装和用户手册安装前请阅读本手册。当任何垫被踩下时，导电板接触，电路中的电阻下降。这由关闭机器的控制单元监控。将检测到主接线或控制单元中的任何单个电气故障，并且控制单元输出将进入安全状态。模制乙烯基传感器垫密封至控制单元。该单元包括一个八通道传感垫系统。当踩下任何垫子时，控制单元将关闭机器，并在信道故障状态显示屏上显示正在操作的垫子。有两种操作模式手动复位和自动复位。号。
After installation, this manual covers the installation and use of all components of the system, including sensor pads with special shapes and sizes. All installation procedures shall be carried out by suitably trained and qualified personnel and shall comply with statutory safety requirements. Please read this manual completely before installation. After installation, keep this manual in a safe and accessible place. For further assistance, please contact the supplier. Section Storage and Handling Storage controls and pad sensors should be stored within a temperature range of+. Cushion sensors should be stored vertically. The handling and transport controls and pad sensors shall be transported within a temperature range of to+. If necessary, the original or similar packaging shall be used with reinforcement to prevent damage and bending. Always open the package carefully to avoid being damaged by knives, etc. When the sensor pad moves in place, do not pull or lift the sensor through its connecting wire. For larger sensor pads, two people are required to safely lift and prevent the risk of damaging the sensor pads by excessive bending. Section System Description The system consists of one or more interconnected pressure sensitive pads and a control unit. There is no "dead zone" in the detection area. The single sensor pad has rectangular standard size and special cutting shape. The maximum size is the maximum standard pad. All sensor pads have the same structure and operating principle. Each cushion has two conductive plates separated by non-conductive compressible partitions. These pads work under and in series to form a ground sensing system in the hazardous area around the machine. The circuit through the mat is monitored by the control unit. When the area is free, the control unit provides information to the machine control circuit to determine the behavior or situation that may cause personal injury, property loss or economic loss. Precautions can help you identify hazards, avoid hazards and recognize consequences. Important information identifies information that is critical to the successful application and understanding of the product. Shock hazard labels may be located on or inside the equipment, such as drives or motors, to alert people that voltage may be present. For each contactor, please refer to the installation of pressure-sensitive safety pad system and the user manual. Please read this manual before installation. When any pad is stepped down, the conductive plate contacts and the resistance in the circuit decreases. This is monitored by the control unit that shuts down the machine. Any single electrical fault in the main wiring or control unit will be detected, and the control unit output will enter the safe state. Molded vinyl sensor pads are sealed to the control unit. The unit includes an eight channel sensing pad system. When any mat is depressed, the control unit shuts down the machine and displays the mat in operation on the channel fault status display. There are two operation modes: manual reset and automatic reset. number.
